Kontron mITX-SKL-S-H110 User manual


USER GUIDE
mITX-SKL-S-H110
Doc. Rev. 1.4
Doc-ID: 1061-1165

mITX-SKL-S-H110 – Rev. 1.4
This page has been intentionally left blank

mITX-SKL-S/H110 – Rev. 1.1
www.kontron.com // 3

MITX
-SKL-S-H110 - USER GUIDE
Disclaimer
Kontron would like to point out that the information contained in this manual may be subject to alteration,
particularly as a result of the constant upgrading of Kontron products. This document does not entail any guarantee
on the part of Kontron with respect to technical processes described in the manual or any product characteristics
set out in the manual. Kontron assumes no responsibility or liability for the use of the described product(s), conveys
no license or title under any patent, copyright or mask work rights to these products and makes no representations
or warranties that these products are free from patent, copyright or mask work right infringement unless otherwise
specified. Applications that are described in this manual are for illustration purposes only. Kontron makes no
representation or warranty that such application will be suitable for the specified use without further testing or
modification. Kontron expressly informs the user that this manual only contains a general description of processes
and instructions which may not be applicable in every individual case. In cases of doubt, please contact Kontron.
This manual is protected by copyright. All rights are reserved by Kontron. No part of this document may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer
language, in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), without the
express written permission of Kontron. Kontron points out that the information contained in this manual is
constantly being updated in line with the technical alterations and improvements made by Kontron to the products
and thus this manual only reflects the technical status of the products by Kontron at the time of publishing.
Brand and product names are trademarks or registered trademarks of their respective owners.
©2018 by Kontron S&T AG
Kontron S&T AG
Lise-Meitner-Str. 3-5
86156 Augsburg
Germany
www.kontron.com

mITX-SKL-S-H110 – Rev. 1.4
Revision History
Revision Brief Description of Changes Date of Issue
1.0 Basic draft 2017-Jan-25
1.1 modified part numbers 2017-April-25
1.2 Accessories list added, corrections 2017-Aug-10
1.3 typos corrected 2018-Jan-12
1.4 block diagram added 2018-Jan-24
Life Support Policy
KONTRON’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT EXPRESS WRITTEN APPROVAL OF THE GENERAL MANAGER OF KONTRON.
As used herein:
Life support devices or systems are devices or systems which (a) are intended for surgical implant into body or (b)
support or sustain life and whose failure to perform when properly used in accordance with instructions for use
provided in the labelling can be reasonably expected to result in significant injury to the user.
A critical component is any component of a life support device or system whose failure to perform can be
reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
Customer Support
Find Kontron contacts by visiting: http://www.kontron.com/support.
Customer Service
As a trusted technology innovator and global solutions provider, Kontron extends its embedded market strengths
into a services portfolio allowing companies to break the barriers of traditional product lifecycles. Proven product
expertise coupled with collaborative and highly-experienced support enables Kontron to provide exceptional peace
of mind to build and maintain successful products.
For more details on Kontron’s service offerings such as: enhanced repair services, extended warranty, Kontron
training academy, and more visit http://www.kontron.com/support-and-services/services.
Customer Comments
If you have any difficulties using this guide, discover an error, or just want to provide some feedback, please contact
Kontron support. Detail any errors you find. We will correct the errors or problems as soon as possible and post the
revised user guide on our website. Thank you

mITX-SKL-S/H110 – Rev. 1.1
www.kontron.com // 5
Symbols
The following symbols may be used in this manual
DANGER indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not avoided,
may result in minor or moderate injury.
NOTICE indicates a property damage message.
Electric Shock!
This symbol and title warn of hazards due to electrical shocks (> 60 V) when touching
products or parts of them. Failure to observe the precautions indicated and/or prescribed by
the law may endanger your life/health and/or result in damage to your material.
Please refer also to the "High-Voltage Safety Instructions" portion below in this section.
ESD Sensitive Device!
This symbol and title inform that the electronic boards and their components are sensitive
to static electricity. Care must therefore be taken during all handling operations and
inspections of this product in order to ensure product integrity at all times.
HOT Surface!
Do NOT touch! Allow to cool before servicing.
This symbol indicates general information about the product and the user manual.
This symbol also indicates detail information about the specific product configuration.
This symbol precedes helpful hints and tips for daily use.

mITX-SKL-S/H110 – Rev. 1.1
www.kontron.com // 6
Table of Contents
Symbols .................................................................................................................................................................................................................5
Table of Contents ...............................................................................................................................................................................................6
List of Tables....................................................................................................................................................................................................... 8
List of Figures ......................................................................................................................................................................................................9
1/ Introduction..........................................................................................................................................................................................10
2/ Description.............................................................................................................................................................................................11
3/ Installation procedure ......................................................................................................................................................................12
3.1. Packing Check List.....................................................................................................................................................................................12
3.2. Installing the Board .................................................................................................................................................................................12
3.3. Requirements IEC60950-1 .....................................................................................................................................................................13
3.4. Product Variants.......................................................................................................................................................................................13
3.5. Accessories List.........................................................................................................................................................................................13
3.6. Lithium Battery Precautions.................................................................................................................................................................14
4/ System Specifications.......................................................................................................................................................................15
4.1. Component Main Data.............................................................................................................................................................................15
4.2. Block Diagram ...........................................................................................................................................................................................19
5/ Jumpers and Connectors ................................................................................................................................................................20
5.1. Hardware Configuration Setting .........................................................................................................................................................20
5.1.1. Jumpers and Connectors.....................................................................................................................................................................20
5.2. Mainboard Placement and Rear I/O Locations...............................................................................................................................21
5.3. Rear Side.....................................................................................................................................................................................................22
6/ Pin Definitions.....................................................................................................................................................................................23
6.1. Processor Support...................................................................................................................................................................................24
6.2. System Memory Support......................................................................................................................................................................24
6.3. Ethernet Connectors (I/O area).......................................................................................................................................................... 25
6.4. USB Connectors (I/O area)...................................................................................................................................................................26
6.5. Audio Jack Connectors (I/O area).......................................................................................................................................................28
6.6. Fan Connectors (internal).....................................................................................................................................................................29
6.7. Front Panel 1 (internal)..........................................................................................................................................................................30
6.8. USB1, USB2 (internal).............................................................................................................................................................................30
6.9. COM3/COM4 (internal)...........................................................................................................................................................................31
6.10. COM9_SW1/2 Internal .........................................................................................................................................................................32
6.11. GPIO Internal ............................................................................................................................................................................................32
6.12. CASE_OPEN Internal .............................................................................................................................................................................33
6.13. CMOS1 Internal ....................................................................................................................................................................................... 33
6.14. SPK Internal............................................................................................................................................................................................. 33
6.15. LCD_PWR1 Internal................................................................................................................................................................................34
6.16. LCD_CTL Internal ...................................................................................................................................................................................34
6.17. LVDS (internal)........................................................................................................................................................................................ 35
6.18. SATA (Serial ATA) Disk Interfaces (internal) ................................................................................................................................36
7/ BIOS........................................................................................................................................................................................................ 37
7.1. Starting the uEFI BIOS ............................................................................................................................................................................. 37
7.2. Setup Menus..............................................................................................................................................................................................38
7.2.1. Main Setup Menu ..................................................................................................................................................................................38
List of Acronyms..............................................................................................................................................................................................54
About Kontron .................................................................................................................................................................................................. 55

mITX-SKL-S/H110 – Rev. 1.1
www.kontron.com // 7

mITX-SKL-S/H110 – Rev. 1.1
www.kontron.com // 8
List of Tables
Table 1: Processor Support............................................................................................................................................................................13
Table 2: Accessories List for mITX-SKL-S/H110.....................................................................................................................................13
Table 3: Component Main Data....................................................................................................................................................................15
Table 4: Environmental Conditions ............................................................................................................................................................18
Table 5: Connector Definitions....................................................................................................................................................................23
Table 6: Processor Support..........................................................................................................................................................................24
Table 7: Pin Assignment DP Connector .................................................................................................................................................... 25
Table 8: Signal Description........................................................................................................................................................................... 25
Table 9: Pin Assignment................................................................................................................................................................................26
Table 10: Signal Description.........................................................................................................................................................................26
Table 11: Navigation ........................................................................................................................................................................................ 37
Table 12: Main Setup Menu Sub-Screens and Functions ...................................................................................................................38

mITX-SKL-S/H110 – Rev. 1.1
www.kontron.com // 9
List of Figures
Figure 1: Block Diagram ..................................................................................................................................................................................19
Figure 2: Front Side..........................................................................................................................................................................................21
Figure 3: Rear Side...........................................................................................................................................................................................22
Figure 4: Ethernet Connector ...................................................................................................................................................................... 25
Figure 5: USB 2.0 / 3.0 socket......................................................................................................................................................................26
Figure 6: USB 2.0 High Speed Cable...........................................................................................................................................................26
Figure 7: USB 3.0 High Speed Cable ........................................................................................................................................................... 27
Figure 8: Audio Jack.........................................................................................................................................................................................28
Figure 9: 4-pin Fan Connector.....................................................................................................................................................................29
Figure 10: FP1 Connector ...............................................................................................................................................................................30
Figure 11: USB Internal Connector ..............................................................................................................................................................30
Figure 12: COM3/4 Internal Connector......................................................................................................................................................31
Figure 13: Available Cable Kit (DB9 adapter cables) .............................................................................................................................31
Figure 14: COM9_SW1/2 Internal Connector..........................................................................................................................................32
Figure 15: GPIO Internal Connector ............................................................................................................................................................32
Figure 16: CASE_OPEN Internal Connector.............................................................................................................................................. 33
Figure 17: CMOS1 Internal Connector ........................................................................................................................................................33
Figure 18: SPK Internal Connector............................................................................................................................................................. 33
Figure 19: LCD_PWR1 Internal Connector ................................................................................................................................................34
Figure 20: LCD_CTL Internal Connector ...................................................................................................................................................34
Figure 21: LVDS Connector............................................................................................................................................................................ 35
Figure 22: SATA Connector...........................................................................................................................................................................36
Figure 23: Available Cable Kit ...................................................................................................................................................................... 36
Figure 24: BIOS Main Menu Screen System Date and Time .............................................................................................................. 39
Figure 25: BIOS Advanced Menu Screen ACPI ........................................................................................................................................40
Figure 26: BIOS Advanced Menu Screen TPM .........................................................................................................................................41
Figure 27: BIOS Advanced Menu Screen Wake system.......................................................................................................................42
Figure 28: BIOS Advanced Menu Screen IVT...........................................................................................................................................43
Figure 29: BIOS Advanced Menu Screen USB.........................................................................................................................................44
Figure 30: BIOS Advanced Menu Screen Serial Port ............................................................................................................................45
Figure 31: BIOS Advanced Menu Screen Serial Port .............................................................................................................................46
Figure 32: BIOS Advanced Menu Screen Serial Port.............................................................................................................................47
Figure 33: BIOS Advanced Menu Screen Serial Port.............................................................................................................................48
Figure 34: BIOS Advanced Menu Screen CPU Fan Mode.....................................................................................................................49
Figure 35: BIOS Chipset Menu Screen Boot Display.............................................................................................................................50
Figure 36: BIOS Chipset Menu Screen LAN...............................................................................................................................................51
Figure 37: BIOS Security Menu Screen Password................................................................................................................................. 52
Figure 38: BIOS Security Menu Screen Boot Configuration............................................................................................................... 53

mITX-SKL-S/H110 – Rev. 1.1
www.kontron.com // 10
1/ Introduction
This manual describes the Mini ITX Skylake S/H110 board. This board will also be denoted mITX-SKL-S/H110 within
this Users Guide.
The use of this Users Guide implies a basic knowledge of PC hard- and software. This manual is focused on
describing the mITX-SKL-S/H110 board’s special features and is not intended to be a standard PC textbook.
New users are recommended to study the short installation procedure stated in the following chapter before
switching-on the power.
All configuration and setup of the CPU board is either done automatically or manually by the user via the BIOS setup
menus.
Latest revision of this manual, datasheet, thermal simulations, BIOS, drivers, BSP’s (Board Support Packages),
Mechanical drawings (2D and 3D) can be downloaded from Kontron Web Page.

mITX-SKL-S/H110 – Rev. 1.1
www.kontron.com // 11
2/ Description
The mainboard mITX-SKL-S/H110 aims to benefit user with the Chipset H110 from Intel. The Processor, Graphics and
Memory Controller is built on 14 nm die. See “Processor Support Table” for more specific details.
Main characteristics are:
Support Skylake Family Processors LGA1151 CPU Socket (37.5 mm x 37.5 mm)
Range from 35 to 65W TDP
Intel®SKL H110 PCH
2x NON ECC SODIMM Memory Architecture
Two independet displays by VGA, Display Port, HDMI or LVDS
Dual Gigabit Ethernet
Two Rear COM Ports, Pin 9 for RI/5V/12V selectable
COM1 can select for RS232/RS422/RS485
Two internal serial RS-232 pin headers
Three SATA 3.0 Ports
PCI Express x16 and mPCIe for expansion
Built with these functions, mITX-SKL-S/H110 Mother Board is ideal for ATM, automation, multi-media, gaming, Kiosk,
medical equipment, industrial automation, financial automation, process control, semiconductor equipment, and
network security markets.

mITX-SKL-S/H110 – Rev. 1.1
www.kontron.com // 12
3/ Installation procedure
3.1. Packing Check List
The mITX-SKL-S/H110 package includes the following basic items accompany with this manual.
One main board
One IO shield
If any of these items are damaged or missed, please contact your vendor and save all packing materials for future
replacement and maintenance.
Note: The above packing list is for standard single box packing only.
3.2. Installing the Board
ESD Sensitive Device!
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry.
•Wear ESD-protective clothing and shoes
•Wear an ESD-preventive wrist strap attached to a good earth ground
•Check the resistance value of the wrist strap periodically (OK: 1 MΩto 10 MΩ)
•Transport and store the board in its antistatic bag
•Handle the board at an approved ESD workstation
•Handle the board only by the edges
To get the board running follow these steps:
1.
Turn off the Power Supply
Make sure to use a standard ATX PSU, suitable cable kit and PS_ON#.
2.
Connecting Interface
s
Insert all external cables for hard disk, keyboard etc. A monitor must be connected in order to change BIOS
settings.
3.
Connect PSU
Connect PSU to the board by the ATX+12 V 4-pin connector and also the ATX 20-pin connector (ATX PWR 20-pin
+ 4-pin (Internal Input Power)) to the I/O power jack.
4. Mounting the board in chassis
When mounting the board to chassis etc. please notice that the board contains components
on both sides of the PCB which can easily be damaged if board is handled without
reasonable care. A damaged component can result in malfunction or no function at all.
When fixing the Motherboard on a chassis it is recommended to use screws with integrated washer and a
diameter of >7 mm. Do not use washers with teeth, as they can damage the PCB and cause short circuits.
5.
BIOS Setup
Enter the BIOS setup by pressing the <F2> key during boot up.
Enter “Exit Menu” and Load Setup Defaults.
Refer to the “BIOS Configuration / Setup“ section of this manual for details on BIOS setup.
To clear all BIOS settings, including Password protection, activate “Load Default BIOS
Settings” Jumper for more than
10 sec (without power connected).

mITX-SKL-S/H110 – Rev. 1.1
www.kontron.com // 13
3.3. Requirements IEC60950-1
Take care when designing chassis interface connectors in order to fulfil the IEC60950-1 standard.
Users of mITX-SKL-S/H110 must evaluate the end product to ensure compliance the requirements of the IEC60950-1
safety standard are met:
The motherboard must be installed in a suitable mechanical, electrical and fire enclosure.
The system in its enclosure must be evaluated for temperature and air flow considerations.
The motherboard must be powered by a CSA or UL approved power supply that limits the maximum input current to
10 A via external barrel-type 12 to 24 VDC connector, and to 16 A via internal square 12 VDC ATX connector.
For interfaces having a power pin such as external power or fan, ensure that the connectors and wires are suitably
rated. All connections from or to the product shall be with Safety Extra Low Voltage (SELV) circuits only.
Wires have suitable rating to withstand the maximum available power.
The enclosure of the peripheral device fulfills the fire protecting requirements of IEC60950-1.
3.4. Product Variants
Table 1: Processor Support
Product Number Name Speed Memory
810700-4500 Core™ i7-6700 3.4 GHz 8 MB
810700-4500 Core™ i5-6500 3.2 GHz 6 MB
810700-4500 Core™ i3-6100 3.7 GHz 3 MB
810700-4500 Pentium G4400 2.9 GHz 3 MB
3.5. Accessories List
Table 2: Accessories List for mITX-SKL-S/H110
Product Number Part Name Length
(mm)
1061-6709 USB 2.0 cable 200
1061-6746
LED switch cable 200
1061-6748 SATA cable 300
1061-6750 15-Inverter 700
1061-6752
LVDS cable 700
TBD CABLE BUNBLE - mITX BOARD H110 Chipset
Including following cables:
1061-6709
1061-6746
1061-6748
1061-6750
1061-6752

mITX-SKL-S/H110 – Rev. 1.1
www.kontron.com // 14
3.6. Lithium Battery Precautions
Danger of explosion if the lithium battery is incorrectly replaced.
•Replace only with the same or equivalent type recommended by the manufacturer
•Dispose of used batteries according to the manufacturer’s instructions
VORSICHT! Explosionsgefahr bei unsachgemäßem Austausch der Batterie.
•Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleichwertigen
Typ
•Entsorgung gebrauchter Batterien nach Angaben des Herstellers
ATTENTION! Risque d'explosion avec l'échange inadéquat de la batterie.
•Remplacement seulement par le même ou un type équivalent recommandé par le
producteur
•L'évacuation des batteries usagées conformément à des indications du fabricant
PRECAUCION! Peligro de explosión si la batería se sustituye incorrectamente.
•Sustituya solamente por el mismo o tipo equivalente recomendado por el fabricante
•Disponga las baterías usadas según las instrucciones del fabricante
ADVARSEL! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering.
•Udskiftning må kun ske med batteri af samme fabrikat og type
•Levér det brugte batteri tilbage til leverandøren.
ADVARSEL! Eksplosjonsfare ved feilaktig skifte av batteri.
•Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten.
•Brukte batterier kasseres i henhold til fabrikantens instruksjoner
VARNING! Explosionsfara vid felaktigt batteribyte.
•Använd samma batterityp eller en ekvivalent typ som rekommenderas av
apparattillverkaren.
•Kassera använt batteri enligt fabrikantens instruktion.
VAROITUS! Paristo voi räjähtää, jos se on virheellisesti asennettu.
•Vaihda paristo ainoastaan lalteval- mistajan suosittelemaan tyyppiln
•Hävitä käytetty paristo valmistajan ohjeiden mukaisesti

mITX-SKL-S/H110 – Rev. 1.1
www.kontron.com // 15
4/ System Specifications
4.1. Component Main Data
The table below summarizes the features of the mITX-SKL-S/H110 embedded motherboard.
Table 3: Component Main Data
Motherboard mITX-SKL-S/H110
Form factor Mini ITX (170.18 mm by 170.18 mm)
Processor
Onboard CPU variants
Intel® Skylake-S Processor line, LGA1151 CPU Socket (37.5 mm x 37.5 mm)
Range from 35 to 65 W TDP, Core™ i7-6700, Core™ i5-6500, Core™ i3-6100, Pentium G4400
BIOS
AMI UEFI BIOS with128Mb Serial Peripheral Interface (SPI) Flash ROM support AMT11.0
PCH Intel®SKL PCH 110 series
I/O Control ITE IT8785E-I (4x COMs)
Memory 2x Dual-Channel DDR4SO-DIMM, Support DDR4(1.2
V)1866/2133
MT/s (PC4-1866/ PC4-
2133), max. up to 32 GB memory using 2x16 GB modules
Storage 3 x SATA 3.0
Watchdog Timer Reset; 1 sec.~255 min. and 1 sec. or 1 min./step
Wake On
Wake On LAN, Wake On Time, Wake On USB
H/W Status
Monitor
Monitoring CPU and system temperature, voltage status and fan speed
TPM Infineon SLB9665TT 2.0
Power
management
Support S5, S4, S3, S0
Battery CR2032, 220mAh
See Safety Instructions below this table!
Expansion One PCIe x16 slot (PCIe Gen3), can operate at 2.5 GT/s, 5 GT/s, or 8 GT/s.
Operating System
Support
Windows 8.1, 10
Linux
Board support packages in different flavors, downloadable from the web page
External I/O
LAN , USB3.0 2x RJ-45 LAN Port (with two LED indicators) + dual USB3.0 (4 x USB)
Audio
3 x Audio Jacks for MIC-input, Line-out and Line-input
VGA
1 x VGA connector High rise type
HDMI 1 x HDMI connector right angle type (V1.4a)
Display Port
1 x Display Port connector upright type
COM 1 x RS-232/422/485 D-SUB 9-Pin Ports for COM1
1 x RS-232 D-SUB 9-Pin Ports for COM2
COM1 and COM2 Pin 9 Selection for 5 V/12 V/RI , 5 V and 12 V ( Max. : 1 A output with Fuse )

mITX-SKL-S/H110 – Rev. 1.1
www.kontron.com // 16
Internal I/O
SATA 3 x SATA 3.0 (6
Gb/s)
PC Buzzer
Standard PC buzzer on board
USB 1 x (2 x 5 ) 2.54
mm pin-header , supports 2 x USB 2.0
GPIO 1 x (2 x 5 ) 2.00
mm box-header (voltage level 3.3
V)
LVDS 1 x ( 2 x 20 ) 1.25
mm pin-header for 24-bit
Mini PCIe
1 x for half size (co-layout m-SATA)
Audio 1 x ( 1 x 4 ) 2.0
mm pin-header for Speaker with 2
W + 2
W amplifier
Serial 2 x RS-232 pin-header 2.0
mm
Internal Header
Fan Power 2 x (1 x 4 ) 2.54
mm pin-header for CPU & System fan with Pulse Width Modulation (PWM)
function
Chassis Intrusion 1 x (1 x 3 ) 2
mm pin-header
CMOS Clear 1 x (1 x 3 ) 2
mm pin-header
Front Panel
1 x (2 x 5 ) 2.54 mm pin-header
Power COM pin 9 2 x ( 2 x 3 ) 2.0
mm pin-header; ( 1: 5
V , 3: 12
V , 5: RI ; 2,4,6: Pin9 )
Display
Graphics Controller
Intel®Gen 9 LP (generation 9 Low Power) graphics core
1. Support below API
Direct3D* 2015, Direct3D 11.2, Direct3D 11.1, Direct3D 9, Direct3D 10, Direct2D
OpenGL* 5.0
OpenCL* 2.1, OpenCL 2.0, OpenCL 1.2
2. Supports full HW accelerated video decoding for AVC, VC1, MPEG2, HEVC, VP8, JPEG.
3. Supports full HW accelerated video encode for AVC, MPEG2, HEVC, VP8.
4. Switchable/Hybrid graphics when discrete graphics card available.
DP to LVDS
Controller
Realtek® RTD2136
DP to VGA
Controller
Parade PS8613
Display Interface
VGA, Display Port 1.2, HDMI 1.4 (DDI x 3) and LVDS
Note: Three (3) Independent Displays Max.
Resolution
VGA 1920x1200
DP/LVDS 1920x1200 @ 60 Hz, 24 bpp (One panel display)
HDMI 4096x2160 @ 24 Hz, 24 bpp (One panel display)
Ethernet
Controller LAN1: Intel® I219LM(Jacksonville) 10/100/1000 Gigabit Ethernet PHY with AMT11.0
LAN2: Intel® I211AT10/100/1000 Gigabit Ethernet Controller

mITX-SKL-S/H110 – Rev. 1.1
www.kontron.com // 17
Interface IEEE 802.3 10BASE-T / 100BASE-TX / 1000BASE-T compliant
Audio
HDAC
Realtek®ALC269Q High Definition Audio Codec
Power Supply
Power Type 4-pin ATX 12V power connector
and :
20-pin ATX Power connector,
Danger of explosion if the lithium battery is incorrectly replaced.
•Replace only with the same or equivalent type recommended by the manufacturer
•Dispose of used batteries according to the manufacturer’s instructions

mITX-SKL-S/H110 – Rev. 1.1
www.kontron.com // 18
Table 4: Environmental Conditions
Operating 0°C to +60°C (32°F~140°F) operating temperature (forced cooling).
It is the customer’s responsibility to provide sufficient airflow around each of the
components to keep them within allowed temperature range. Please refer to the thermal
simulation report for information about airflow.
10% to 90% relative humidity (non-condensing)
Storage -20°C~80°C (-4°F~176°F); lower limit of storage temperature is defined by specification
restriction of on-board CR2032 battery.
Board with battery has been verified for storage temperature down to -40 C by Kontron.
Up to 95% relative humidity (non-condensing)
Radiated Emissions
(EMI)
All Peripheral interfaces intended for connection to external equipment are EMI protected.
FCC class B Generic Emission Standard
Safety IEC 60950-1: 2005, 2nd Edition
UL 60950-1
CSA C22.2 No. 60950-1
Product Category: Information Technology Equipment Including Electrical Business
Equipment. Product Category CCN: NWGQ2, NWGQ8. File number: E147705
Restriction of
Hazardous
Substances (RoHS)
All boards in the mITX-SKL family are RoHS compliant

mITX-SKL-S/H110 – Rev. 1.1
www.kontron.com // 19
4.2. Block Diagram
Figure 1: Block Diagram

mITX-SKL-S/H110 – Rev. 1.1
www.kontron.com // 20
5/ Jumpers and Connectors
5.1. Hardware Configuration Setting
This chapter gives the definitions and shows the positions of jumpers, headers and connectors. All of the
configuration jumpers on the board are in the proper position. The default settings shipped from factory are marked
with an asterisk (*).
In general, jumpers on the board are used to select options for certain features. Some of the jumpers are designed to
be user-configurable, allowing for system enhancement. The others are for testing purpose only and should not be
altered. To select any option, cover the jumper cap over (SHORT) or remove (NC) it from the jumper pins according to
the following instructions. Here, NC stands for “Not Connect”.
5.1.1. Jumpers and Connectors
Jumpers Function Remark
CLR_CMOS1 Clear CMOS 1 x 3 header
COM9_SW1 COM2 Pin 9 Setting 2 x 3 header
COM9_SW2 COM1 Pin 9 Setting 2 x 3 header
LCD_PWR LCD Power source selection 1 x 3 header
INTR Case Open 1 x 3 header
Connectors Function Remark
CPU_FAN CPU FAN Connector 1 x 4 wafer
SYS_FAN SYS FAN Connector 1 x 4 wafer
FP Front Panel Connector 2 x 5 header
USB2_P1 USB 2.0 Connector 2 x 5 header
SPK Speaker Connector 1 x 4 wafer
GPIO GPIO Port Connector 2 x 5 box header
LCD_CTL LCD Backlight Control Connector 1 x 5 wafer
LVDS LVDS Connector 2 x 20 connector
ATX ATX Power Connector 2 x 10 Connector
PWR_CPU1 CPU Power Connector 2 x 2 Connector
MINI-PCIE Mini PCIe Connector
PCIEx16X PCIe x16 3.0 Connector
SPI_SOCKET Bios Socket
SATA1 SATA3.0 Connector Standard
SATA2 SATA3.0 Connector Standard
SATA3 SATA3.0 Connector Standard
BAT1 Battery Socket CR2032 compatible
DIMM1 Memory Socket Slot
DIMM2 Memory Socket Slot