KOOPOOL 2103TC User manual

User Manual
2103TC
Double Flaring Tool
KOOPOOL
UNPACKING:
Please carefully inspect your product after unpacking.
Ensure that all parts of the tool set are included and delivered in a good condition.
If any parts are missing or damaged, please attempt to contact us directly for refund and
replacement before you start to use it!
CUSTOMER SERVICE:[email protected]

Page 2
ASSEMBLY PRECAUTIONS
1. Assemble and use only according to these instructions. Improper assembly or use can create hazards.
2. Wear ANSI-approved safety goggles and heavyduty work gloves during assembly and use.
3. Keep assembly and use area clean and well lit.
4. Keep bystanders out of the area during assembly or use.
5. Do not assemble or use when tired or when under the influence of drugs or medication.
6. This product is not a toy. Do not allow children to play with or near this item.
7. Use for intended purpose(s) only.
8. Inspect before use; do not use if parts are damaged.
9. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact Harbor
Freight Tools for a replacement.
10. The quality of flares produced by this tool is largely dependent on the quality and preparation
of the workpiece and also the care of the user.
Operating Instructions
1. This tool is used to create a double flared end on Copper, Aluminum, Soft Steel and Brass tubing.
2. You may flare tubing from 3/16" to 5/8" in diameter.
3. Straighten tubing as much as possible, and then be sure to make a clean cut straight across the
tube to avoid a crooked flare. Deburr inner and outer edges. The tube cannot be crushed.
4. Place the flare nut (not included) over the tubing before flaring. Back off the Flaring Cone and remove
the pivoting wing nut. Slide Yoke (1) over Flaring Bar (2). See Figure A.
5. Loosen the two wing nuts and insert the prepared tubing into the proper-size hole in the Flaring Bar.
The end of the tube must extend above the top of the bar as much as the height of the Adapter
Shoulder. For the two smallest Adapters, extend the tube as far as the shoulder on the largest adapter.
See Figure B.
6. After setting the tubing height, tighten the Flaring Bar on the tube by tightening the two wing nuts.
7. Lightly oil the appropriate sized Adapter and insert it into the end of the tube, button end down.
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
Flaring Bar
Flaring Cone
Yoke
Figure A
Adapter Shoulder
Tubing
Figure B
[email protected]

8. Position the Flaring Cone over the Adapter.
See Figure C.
9. Turn the Handle of the Yoke driving the Adapter into the
end of the tube. The tube will flare. Continue flaring
until the shoulder of the Adapter touches the Flaring Bar.
10. Back off the Yoke and remove the Adapter.
11. Reposition Flaring Cone over tubing and screw the
Yoke down again on the end of the tube until the tubing
folds back on itself, forming a 45 degree double flare.
12. Loosen the Yoke, and the wing nuts. Remove the Yoke
and Flaring Bar from the tube.
13. Clean and lightly lubricate the tool, and store it out of
reach of children.
Maintenance and Servicing
1. Before each use, inspect general condition of tool. Check for misalignment or binding of moving parts,
cracked or broken parts, and any other condition that may affect its safe operation. Do not use
damaged equipment.
2. After use, clean external surfaces. Then dry and lubricate all moving parts. Do not use solvents.
3. When storing, keep Flaring Tool and its accessories in its Carrying Case and store in a clean, dry,
safe location.
4. CAUTION! All maintenance, service, and repairs not mentioned in this manual must only be
performed by a qualified service technician.
Page 3
Flaring
Cone
Flaring Bar
Adapter
Tube
Figure C
Parts List and Diagram
1
2
3
4
56
7
8
9
10
Qty
1
1
1
1
1
1
1
1
1
Description
Part
1
2
3
4
5
6
7
8
9
110
Yoke
Flaring Bar
3/16" Adapter
1/4" Adapter
3/8" Adapter
7/16" Adapter
1/2" Adapter
5/8" Adapter
5/16" Adapter
Tube Cutter
111 Carrying Case (not shown)
[email protected]

u
WARRANTY INFORMATION AND LIABILITY:
The manufacturer and supplier cannot accept any responsibility for any incorrect readings
and any consequences that occur should an inaccurate reading take place.
The specifications of this product may change without prior notice.
This product is not a toy. Keep out of the reach of children.
No part of this manual may be reproduced without written consent of the manufacturer
In the event of a warranty claim, the warranty period shall not be extended.
We can only accept warranty claims when accompanied by proof of purchase and this
warranty information.
Please contact us with any complaints. our customer service: [email protected]
With defects in wear to parts, our warranty shall apply within the framework of our statutory
liability.
We can accept no liability for defects due to improper handling, wear, external influences,
knocks or falls.
LIMITED LIFETIME WARRANTY is confident of the quality and After-Sale-services of all its
products and makes every effort to assure the products meet the high-quality standards.
If you’re not completely satisfied with your KOOPOOL product, please simply contact us within
30 days of receiving it at: [email protected]，for a free replacement or a full refund.
Each KOOPOOL non-electric product is warranted to be free of defects in material and
workmanship in the 12 months following the date of purchase.
Warranty does not apply to normal wear and tear, criminal activity, improper installation,
environmental factors, accidental damage, lack of maintenance or misuse.
Some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation of exclusion may not apply to you.
At KOOPOOL discretion, a defective product will be repaired or replaced. This warranty gives
you specific legal rights, but some states do not allow the exclusion or limitation of incidental
or consequential damages, so you may also have other rights which vary from state to state,
and the above limitation of exclusion may not apply to you.
If you think you might have a defective product, please contact us at [email protected]
to start the (free) procedure to start refund or replace.