Koso 10032749 User manual

5
Adapter plate for switch
X1
3-3
Wiring installation instructions
wh000axg1a
8
Bar-end cap X2
2
G type switch X1
3
7
M3 nut X1
1
Heated grip X2
4
Velcro X1
9
6
M3XP0.5X25L screw X1
Connecting wire X1
G l u e X1
Specifications
2-1
PRESS THE
BUTTON
ONCE
FLASH LIGHT ON
PRESS THE
BUTTON 3
SECONDS
3. Thrust the heated grip into
the handlebar.
If the heating grip and the
handlebar are under
tighten; then apply the
super glue (Accessory 9)
to strengthen the
tightness to ensure there
will be no twisting during
riding.
To install, please do not use the
tool to knock on or twist to thrust
in the heating grip for thus doing
will break or damage the wire
inside the handlebar.
1.
4.
To install the side cap onto
the heating grip, please
insert the top cap into the
top groove and then follow
to push it downward into the
bottom groove.
2.
3-2
Installation instruction
Installation steps
1. G switch (Accessory 2)
Velcro (Accessory 4)
Adapter plate for switch (Accessory 5)
M3XP0.5X25L screw (Accessory 6)
M3 nut (Accessory 7)
2.
3.
4.
5.
0.2 Nm (2 kgf.cm)
0.2 Nm (2 kgf.cm)
3-1
Practical installation instruction
Please proceed as follows
1.
2.
Please use an appropriate
tool to remove the original
handlebar.
Please apply a cleaning
agent and wipe back and
forth to clean away the
residual glue from the
handlebar.
Need to keep cetrain clearace
●Voltage
●Switch size
DC 12 V
W38.2 X L38.2 X H16.5 mm
●Effective temperature range JIS D 0203
●Fuse type 4A (ASP)
●Heating stage 1st stage (low) ~ 5th stage (high)
●Switch weight (with wire) About 88 g
Level 1 Temperature Curve
Level 2 Temperature Curve
Level 3 Temperature Curve
Level 4 Temperature Curve
Level 5 Temperature Curve
Heated grip testing data
2-2
2.
1.
3.
5. 4.
34.8 mm
34.8 mm 38.2 mm
16.5 mm
0
0
20
40
60
80
100
120
510 15 20 25 30
Design and specifications are subject to change without notice!
Please contact your local distributor if the items received are not the same as the one listed above.
1
Accessories
For installation, please follow the steps described in manual. Any damage caused by wrong installation shall be imputed to the users.
●
Don't break or modify the wire. To avoid the short circuit, please don't pull the wire when installing.
●
Do not disassemble or change any parts excluding the manual description.
●
The interior examination or maintenance should be executed by our professionals.
●
ATTENTION!
●Thank you for purchasing the KOSO heated grips. Before installing, please read the instruction carefully and keep it for future reference.
To install the heating grip onto
the throttle sleeve in right side,
please note that throttle must be
maintained a safe clearance
plus a suitable surplus of wiring;
also they shall be tested by
rotating to and fro for avoiding
interference.
You could get the installation details from the information behind the mark.
Some processes must be followed to avoid the affection caused by wrong installation.
Some processes must be followed to avoid damages to yourself or the public.
Some processes must be followed to avoid the damage to the vehicle.
If any information dealt with in the manual remains unclear seek professional assistance.
◎MARK MEANING:
Figure 1 Figure 4
Figure 5Figure 2
Figure 3
Black / Ground wire connect to the vehicle
body or the engine (It must be a good ground)
Red / Positive wire connecting
to the key on switch (DC 12 V)
G type switch (Accessory 2)
Heated grip (Accessory 1)
Connecting wire (Accessor y 3)
The testing environment is under 26 Degrees Celsius, with working voltage of 13.5 V.
(Minute)
(℃)
INSTRUCTION

●Ex：Set the heating stage from 1st
stage to 3rd stage.
Specifications
4-1
Standby mode, press and hold the
push button 3 seconds to enter into
the quick heating mode.
●
Quick heating mode.
●
Low-voltage mode Description
4-2
At this moment, LED flashes.
● The heating system will be turned off automatically when the voltage is lower than 11.5 V.
● Standby mode will be enabled when the voltage over 11.5 V is restored.
Trouble shooting
5
※If still can't solve the problems according to the step above, please contact with distributors or us.
The following situation do not indicate malfunction of the meter. Pleasecheck the following before taking it in for repair.
Trouble
LED indication does not activate.
● Power supply cable
It might causing by the setting
is not proper set up.
→ Please make sure and
double check if setting is under
the idle mode.
It might be the battery is
running out.
→ Please check your battery
voltage as soon as possible.
It might be causing by no
power supply.
→Please check if power
harness and fuse broken or
disconnected.
→Please check if positive pole
and negative pole is well
connected.
It might be causing by
improper setup.
→Please check if all function
setup is properly proceeded.
Please referring to 4-1
Specification and check with
each step.
disconnected.
→Please check if power supply
cable is broken or disconnect-
ed.
→Please check if positive and
negative poles are properly
connected.
●
●
●
●
Check item Trouble
When turn the key on, the
headed grip is not heating up.
Check item
At this moment, the LED lights will
flash once from left to right.
At this moment, the LED lights will
flash once from left to right.
At this moment, the LED lights will
flash once from left to right.
●
wh000axg1a
●Memory of heating mode.
At this moment, the LED indicators
are on.
At this moment, LED flashes.
●Ex：The last heating stage in memory
before turning off the switch is the 3rd
stage.
B. Memory of heating mode
C. Memory of heating mode
C.Quick heating mode
B. Memory of heating mode
PUSH
OPEN
LOCK
OFF ON
●Example：To set the heating stage to
the third stage.
●
●Press the push button to select the
desired set value.
●Ex：The current heating stage is set
to the 1st stage.
A. Heating stage setup
Standby mode, press the push button
once to enter into the heating mode.
●
C.Quick heating mode
B.Memory of heating mode
Turn the key on to enter the stand by
mode.
This stage is for self-check
without enabling the heating
function.
The default set is off.
The switch is characterized with
memory function；and 3
seconds after setting the
number of stage, the set
number of stage will be
memorized automatically. If the temperature is felt
enough, press the push button
once to stop the quick heating.
Setting range: Off → 1st stage
(low temperature) → 2nd stage
→ 3rd stage → 4th stage → 5th
stage (high temperature)