Kovert 22x PTZ User manual

www.kovert.com OPTION F Doc PTZ054.doc
PTZ054 22x PTZ Module rev : 1.0
Email: [e-mail] 1systemq.com
The new 22x PTZ module for the
Pan, Tilt and Zoom ranges of domes.
Camera Instruction Manual.
1. OSD Navigation.
The way to navigate to the menu options is dependant on the model of PTZ that the
module has been installed in.
1.1 The PTZ300 and PTZ500 Series.
When the module is installed in the PTZ300 and PTZ500 series the OSD menu is
accessed by CALL 57 from a keypad that is connected to the PTZ via RS485 comms.
Navigation is done by the TELE & WIDE buttons and selection is made with the
NEAR & FAR buttons.
To exit the OSD menu use CALL 57 on the keypad.
1.2 The PTZ400 and PTZ600 Series.
When the module is installed in the PTZ400 and PTZ600 series the OSD menu is
accessed by CALL 95 from a keypad that is connected to the PTZ via RS485 comms.
This will enter the menu system of the PTZ. Go to the CAMERA MENU,
navigation is done by the joystick UP & DOWN and selection is made by moving the
joystick RIGHT. Once in the camera menu go to the MENU OF CAM option and
move the joystick RIGHT. Now you are in the module menu, navigation is done by
the TELE & WIDE buttons and selection is made with the NEAR & FAR buttons.
To exit the OSD menu press the CLOSE button on the keypad.

www.kovert.com OPTION F Doc PTZ054.doc
PTZ054 22x PTZ Module rev : 1.0
Email: [e-mail] 2systemq.com
2. The module Menu Structure.
Once in the menu system of the camera module the following options are available.
BACKLIGHT Used to switch backlight compensation on or off. This can be
used to improve image quality when the light behind the object
causes the object to appear dark or dim.
SLOW SHT This setting allows the module to slow the shutter speed down
or to turn the slow shutter off. The range of shutter speeds
range from 2 to 128.
DAY/NIGHT This option is used to set the module to either switch
automatically between day and night mode depending upon the
level of light available. (AUTO) will stay in colour during the
day and switch to black & white at night, (OFF) will stay in
colour mode and (ON) will stay in black and white mode.
WB CONTROL This option is used to determine how the white balance is
controlled by the module. When set to AUTO the module will
automatically alter the white balance in relation to the amount
of light in the image, whereas when set to PUSH the module
will only set the white balance once when the camera has
moved into position.
SHUTTER Always set to AUTO.
CAMERA ID A numeric identifying number between 0 and 255 which is then
displayed onthe screen.
ZOOM START This option is the setting of the minimum zoom that the module
will allow x1 to x22. For example if this is set to x5 the
operator will not be able to use the x1 to x4 modes when using
the WIDE & TELE buttons.
MENU OF CAM
1. BACKLIGHT (OFF,ON)
2. SLOW SHUTTER (OFF or 2 to 128)
3. DAY/NIGHT (OFF,ON,AUTO)
4. WB CONTROL (PUSH,AUTO)
5. SHUTTER (AUTO)
6. CAMERA ID (NUMERIC 3 DIGIT 000 to 255)
7. ZOOM START (x001 to x022)
8. ZOOM STOP (x001 to x220)
9. BRIGHTNESS (1 to 48)
10. SHARPNESS (0 to 18)
11. FOCUS (PUSH or AUTO)
12. INIT SET (OFF or ON)

www.kovert.com OPTION F Doc PTZ054.doc
PTZ054 22x PTZ Module rev : 1.0
Email: [e-mail] 3systemq.com
ZOOM STOP This option is the setting of the maximum zoom that the
module will allow x1 to x220. For example if this is set to x22
the operator will only be able to zoom to the limit of the optical
zoom and not the digital zoom up to x300.
BRIGHTNESS This alters the brightness of the image output from the module
from 0 to 48, where 0 is the darkest and 48 the brightest.
SHARPNESS This adjusts the sharpness of the image from 0 (low) to 15
(high).
FOCUS MODE When set to PUSH the camera module will do a single push to
focus the camera and will not try to refocus after the initial
push. When set to AUTO the camera will automatically focus.
INIT SET When switched ON this option will reset all of the options
within the menu back to their factory default setting.