Kozyard Alicia User manual

Assembly Manual
Alicia swing chair
Kozyard LLC Products

PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
•
PLEASE SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU HAVE ALL OF THE PARTS LISTED.
• SHOULD YOU EXPERIENCE ANY DIFFICULTY DURING ASSEMBLY OR IF ANY PARTS IS MISSING OR
DAMAGED
CONTACT OUR CUSTOMER SERVICE BY EMAIL : [e-mail] OR CALL TOLL FREE: 886-355-0018 .
•
PLEASE PROVIDE THE FOLLOWING INFORMATION:
1. MODEL NUMBER OF THE PRODUCT.
2. PART NUMBER AND MATERIAL CODE OF THE PART FROM THE PARTS LIST SHOW ON ASSEMBLY
INSTRUCTIONS.
• B
efore assembling, make sure that you lay out and identify all parts listed below in the parts list.
•Install on level ground.
•Install not less than 6 feet from any obstruction such as fence, garage, house, overhanging branches, laundry
lines, or electrical wires.
•Tighten all nuts and bolts securely. All bolts should be hand tightened before use. Never use power tools or
excessive force during assembly and tightening of bolts.
ASSEMBLY INSTRUCTION
1

2
PARTS LIST
Front upright support
braces
Rear upright support
braces
Top right cross beamTop left cross beam
Lateral cross bracesSwing arm tubes Rear left cross braceRear right cross brace
S Hook Swing Arms Seat with cushion Side canopy braces
Front&Rear canopy
bracesCanopyBolts M6x30
Bolts M6x40 Bolts M6x45
Bolts M6x50
Bolts M6X63 Bolts M6x65
Bolts M6x68 Bolts M6x90 Nuts Washers
Plastic Screws Nut covers Open Wrench Screwdriver

Connect the Top right cross beam (C) and Top
left cross beam (D). Using bolts (Q), washers (W)
and nuts (V), cover with nut covers (Z)
STEP 2
AttachFront upright support brace (A) and Rear upright support brace (B) to top cross
beams (C&D). Us-
ing bolts (U), washers (W) and nuts (V), cover with nut covers (Z). Repeat the procedure
for the other side. Do not tighten nuts&bolts yet
STEP 1
X2
3

STEP 3
Fasten Lateral cross brace (E) to upright support
braces. Using bolts (N), washers(W) and nuts
(V), cover with nut covers (Z).
STEP 4
Connect the Rear left cross brace (F) and Rear right cross
brace (G). Using bolts (O), washers (W)
and nuts (V), cover with nut covers (Z)
X4
4

5
STEP 5
Fasten rear cross brace (F&G) to rear upright
support braces(B). Using bolts(T), washers (W)
and nuts (V), cover with nut covers (Z).
STEP 6
Open seat assembly (J), attach the end of one swing arm (I) to the seat assembly.
Using bolts (R), washers
(W) and nuts (V), cover with nut covers (Z). Repeat the procedure for the other side.
X2
X2

6
STEP8
Attach one swing arm tube (E) and swing arm (I) to seat assembly (J)
back frame. Using bolts (S), washers (W) and nuts (V),
cover with nut covers (Z) for each side. Fasten another
swing arm tube (E) at the
bend, using bolts(P),
washers (W) and nuts (V),
cover with nut covers (Z)
Attach one S Hook (H) to the top of both swing arm tubes (E). Hang the
other end of the S Hook into
the hole on the angled braces of the top cross beam (C&D). Repeat the
same procedure for the other
side
STEP7
X2
X2

STEP9
Attach the canopy assembly on both sides of the top cross beams (C&D)
with plastic screw (Y)
STEP10
Insert front and rear canopy braces (L) into the
sleeves of the canopy (M). Tie the nylon tapes to
secure the frame and canopy top
7

STEP 11
Insert Part L to part K, Repeat another side.
STEP 12
Be make sure each time to adjustable canopy, By loosing
"Y" part, Change the angle you like, Than again fasten"Y"
part.
8
X4

Kozyar
A
Mer W
rd.com
www.kozyard.com
Toll-fr