KP Electronic Systems ATC100 User manual

ATC100™
Long-Range
Cellular
Alarm Transmitter
Installation Manual
Web Site: www.kpsystems.com
ISRAEL Office
Email: [email protected]
Tefen Industrial Park, Tefen 24959
Tel: [phone] Fax: [phone]
USA Office:
KP ELECTRONICS INC.
Email: [email protected]
415 Sargon Way Suite F Horsham PA 19044
Tel: [phone] Fax: [phone]
P.N.: Book 106 Rev 08 10/9/2013
This Document refers to ATC100™ hardware
ATC100™ General Description
ATC100™ is a long-range, cellular alarm
transmitter. The ATC100 will be able to work at
900/1800 or 850/1900 MHz.
ATC100™ operates in two modes, SMS and TCP/IP.
When ATC100™ detects alarm conditions at one or
more of its inputs; an encoded digital alarm message
is prepared. It is then transmitted to the alarm center,
according to the selected mode. The eight ATC100™
inputs are in normally closed state (NC).
ATC100™ has three sets of connectors: J1, J2, and
the SMA ANT (see Figure 1).
1. J1: A 13-pin contact connector for the
following connections (see Figure 1):
•12 VDC battery (contacts 1 and 2)
•Common Ground (contact 3)
•Eight inputs for sensors
(contacts 4 - 11)
•Two serial communication
connections: SI and SO.
Table 1: LEDs description
Purpose No. of
blinks/Color Description
Net Led
[Led 4-Red] Fast Blinking Modem is not registered
Slow Blinking The modem is registered
Transmission
Led
[Led3-Red]
1 Will blink each time a transmission is made in
SMS Mode
Fast Blinking Will start blinking rapidly at the beginning of a data
transmission (TCP mode)
Status Indication
Led
[Led2-Green]
1Power on reset and all
OK/Received SMS
2SMS was not sent
3Communication problem
4Modem Reset
6 Low battery(bellow 9[V])
8Failed to register to the
network
Fast Blinking No SIM card or PIN code
is enabled
Constant-on
The ATC100 is ready to
receive an event from the
panel or from the direct
inputs.
RSSI Led
[Led1-BiColor]
Off No reception[-113dbm]
Red Poor reception[-111dbm]
Green Good reception[-109-(-51dbm)]
J2: The 10-pin programming connector
Communication parameters are easily
programmed using GUP5000™ utility-
programming software. (See ATC100TM
and GPRS receiver Manual book).
ANT: An external antenna can be connected
using the SMA connector.
Figure 1: ATC100™ External View
Preparing for Operation
Before installing ATC100™ on site, perform
the following preparations:
•Setting communication parameters
•Preparing inputs
•Connecting antenna, sensors and battery
Setting Communication Parameters
See ATC100TM and GPRS receiver Manual
book.
Preparing Inputs
The eight ATC100™ inputs are factory set. By
default they are set as NC (Normally Closed).
Connecting Alarm Panels
Prepare a panel according to manufacturer
rules. There are three ways to connect the
ATC100™ with an alarm panel:
•Caddx NX4, NX6, NX8 or Paradox
SP5500 panels are connected directly to
the serial port J2, using appropriate
cables: INT001™ for Caddx, CAB149™
for Paradox. For Caddx connect all three
wires of the alarm cable to the alarm
panel – lines Red to “Pos” Black to
“Com” Green to “Data”. Connect the
cable to J2. (Connect the INT001™ or
CAB149™ cables before connecting the
battery).
•Any other alarm panel can be connected
via the DI100™, enabling it to transfer
full Contact ID data.
•Connect the alarm panel’s outputs to the
ATC100™ inputs.
Connecting Antenna, Sensors and Battery
1. Connect the antenna to the SMA connector.
2. Connect sensors to J1 (contacts 4–11).
3. Connect the battery to J1: red wire (+) to
contact 1, black wire (-) to contact 2 (see
Figure 2).
4. Connect AC supply to charger.
Figure 2: Sensors Connections

Remote Control Output
1. Connect the "+" of the relay to the
battery positive terminal and to the device
positive output connection.
2. Connect the relay "COM" connection to the
battery negative terminal.
3. Connect the relay N.O contact to the device
negative output connection.
4. Connect the SO from the ATC100 to
the "-" of the relay.
5. Optional – In order to receive confirmation
from the ATC100 about the device status,
connect the relay N.O contact to one of the
ATC100 inputs.
Figure 3: Remote Control Output Connection
Alarm Codes
The ATC100™ can transmit alarms in tow protocols:
Contact ID and 4x2.
When either one of the inputs is activated, or a
troubles occurred, following alarm codes are
transmitted to the alarm center:
Table 2: Alarm Codes (Protocol 4x2)
Alarm T
yp
eAlarm Code Reset Code
Input 1 A1 B1
Input 2 A2 B2
Input 3 A3 B3
Input 4 A4 B4
Input 5 A5 B5
Input 6 A6 B6
Input 7 A7 B7
Input 8 A8 B8
Low battery A9 B9
Test 00
—
Table 3: Alarm Codes (Contact ID)
In Contact ID each input can be programmed via
GUP5000™ to one of the following codes:
Alarm Code Meanin
g
100 Medical
110 Fire Alarm
120 Panic Alarm
121 Duress
130 Burglary
137 Box Tamper
140 General Alarm
150 24Hrs Non Burglary
170 Special Code (KP)
301 AC Loss
409 O/C by Key switch
602 Test
302 Low Battery
144 Sensor Tamper
309 Bat Test Failure
311 Bat Missing/Dead
344 RF receiver Jam Detected
381 RF loss of supervision
384 RF Low Bat
400 Open/Close
358 Low Signal
Technical Specifications:
Modem:
T
yp
e SIM900.
Su
pp
orted Codec Half Rate
O
p
eratin
g
Volta
g
e 3.2-4.5 VDC Max
Power Output. 3 VDC
Tx Current 1.8 A max.
Supported
Frequency's 900/1800
850/1900 Mhz
ATC100TM
O
p
eratin
g
Volta
g
e10.5-14.5 VDC
Standb
y
Current 40mA max.
Tx Current 0.3A max.
Power Output 2W @ 3.6 VDC
(850/900 Mhz)
1W @ 3.6 VDC
(
1800/1900 Mhz
)
Operating Temp. -30oC a 60oC
(
-22oF a 140oF
)
Storage Temp. -40oC a 70oC
(
-40oF a 158oF
)
Weight 0.47 K
g
(
1 lbs
)
Note: Do not forget to insert the SIM
card on the respective slot, and
disable Pin Code if needed (available
via GUP5000).
Important!!
Do Not insert or remove the SIM
card while the ATC100™ is
powered on!!