Kramer VS-88HN User manual

KRAMER ELECTRONICS LTD.
USER MANUAL
MODEL:
VS-88HN
8x8 HDMI Matrix Switcher
P/N: 2900-300155 Rev 5

VS-88HN - Contents i
Contents
1Introduction 1
2Getting Started 2
2.1 Achieving the Best Performance 2
2.2 Safety Instructions 3
2.3 Recycling Kramer Products 3
3Overview 4
3.1 Defining the VS-88HN 8x8 HDMI Matrix Switcher 4
3.2Using the IR Transmitter 7
4Installing in a Rack 8
5Connecting the VS-88HN 8x8 HDMI Matrix Switcher 9
6Operating the VS-88HN 8x8 HDMI Matrix Switcher 11
6.1 Switching an Input to an Output 11
6.2 Acquiring the EDID 11
6.3 Storing and Recalling a Setting 13
6.4 Resetting the IP Parameters 14
6.5 Switching Between Protocol 2000 and Protocol 3000 15
6.6 Connecting via RS-232 15
6.7 Connecting via Ethernet 15
6.8 Upgrading the Firmware 17
7Technical Specifications 18
8Default Communication Parameters 19
9Default EDID 20
10 Kramer Protocol 2000 23
11 Protocol 3000 26
11.1 Kramer Protocol 3000 Syntax 26
11.2 Kramer Protocol 3000 Commands 29
Figures
Figure 1: VS-88HN 8x8 HDMI Matrix Switcher Front Panel 5
Figure 2: VS-88HN 8x8 HDMI Matrix Switcher Rear Panel 6
Figure 3: Connecting the VS-88HN 8x8 HDMI Matrix Switcher 10
Figure 4: Store-Recall Button Configuration 13
Figure 5: Local Area Connection Properties Window 16
Figure 6: Internet Protocol (TCP/IP) Properties Window 17

VS-88HN - Introduction 1
1 Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been
providing a world of unique, creative, and affordable solutions to the vast range of
problems that confront video, audio, presentation, and broadcasting professionals
on a daily basis. In recent years, we have redesigned and upgraded most of our
line, making the best even better!
Our 1,000-plus different models now appear in 11 groups that are clearly defined
by function: GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Routers;
GROUP 3: Control Systems; GROUP 4: Format/Standards Converters; GROUP 5:
Range Extenders and Repeaters; GROUP 6: Specialty AV Products; GROUP 7:
Scan Converters and Scalers; GROUP 8: Cables and Connectors; GROUP 9:
Room Connectivity; GROUP 10: Accessories and Rack Adapters and GROUP 11:
Sierra Video Products.
Congratulations on purchasing your Kramer VS-88HN 8x8 HDMI Matrix Switcher,
which is ideal for the following typical applications:
•Conference room presentations
•Advertising applications
•Rental and staging

2 VS-88HN - Getting Started
2 Getting Started
We recommend that you:
•Unpack the equipment carefully and save the original box and packaging
materials for possible future shipment
•Review the contents of this user manual
•Use Kramer high-performance, high-resolution cables
•Use only the power cord that is supplied with this machine
Go to http://www.kramerelectronics.com to check for up-to-date
user manuals, application programs, and to check if firmware
upgrades are available (where appropriate).
2.1 Achieving the Best Performance
To achieve the best performance:
•Use only good quality connection cables to avoid interference, deterioration
in signal quality due to poor matching, and elevated noise levels (often
associated with low quality cables)
•Do not secure the cables in tight bundles or roll the slack into tight coils
•Avoid interference from neighboring electrical appliances that may adversely
influence signal quality
•Position your Kramer product away from moisture, excessive sunlight and
dust
This equipment is to be used only inside a building. It may only be
connected to other equipment that is installed inside a building.
i
!

VS-88HN - Getting Started 3
2.2 Safety Instructions
Caution: There are no operator serviceable parts inside the unit
Warning: Use only the power cord that is supplied with the unit
Warning: Do not open the unit. High voltages can cause
electrical shock! Servicing by qualified personnel only
Warning: Disconnect the power and unplug the unit from the wall
before installing
2.3 Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC
aims to reduce the amount of WEEE sent for disposal to landfill or incineration by
requiring it to be collected and recycled. To comply with the WEEE Directive,
Kramer Electronics has made arrangements with the European Advanced
Recycling Network (EARN) and will cover any costs of treatment, recycling and
recovery of waste Kramer Electronics branded equipment on arrival at the EARN
facility. For details of Kramer’s recycling arrangements in your particular country
go to our recycling pages at http://www.kramerelectronics.com/support/recycling/.
!

4 VS-88HN - Overview
3 Overview
The VS-88HN is a high quality 8x8 matrix switcher for HDMI signals. It reclocks
and equalizes the signal and can route any input to any or all outputs
simultaneously.
In particular, the VS-88HN features:
•Up to 6.75Gbps data rate (2.25Gbps per graphics channel)
Suitable for resolutions up to UXGA at 60Hz and for all HD resolutions.
•HDTV compatibility
•HDCP compliance
•HDMI support for Deep Color, x.v.Color™, Dolby® TrueHD, Dolby Digital
Plus, DTS−HD®, and linear PCM 7.1 surround sound
•3D pass-through
•I-EDIDPro™ Kramer Intelligent EDID Processing™ – Intelligent EDID
handling & processing algorithm ensures Plug and Play operation for HDMI
systems
•Kramer reKlocking™ & Equalization Technology that rebuilds the digital
signal to travel longer distances
•A lock button to prevent unwanted tampering with the buttons on the front
panel
•16 Preset memory locations for quick access to common configurations
You can control the VS-88HN using the front panel buttons, or remotely via:
•RS-232 serial commands transmitted by a PC, touch screen system or other
serial controller
•The Kramer infrared remote control transmitter
•A PC connected to the Ethernet port on the device via a LAN
•An external remote IR receiver (optional), see Section 3.2
3.1 Defining the VS-88HN 8x8 HDMI Matrix Switcher
This section defines the VS-88HN.

VS-88HN - Overview 5
VS-88HN – Overview 5
Figure 1: VS-88HN 8x8 HDMI Matrix Switcher Front Panel
#
Feature
Function
1 IR Indication LED Lights yellow when receiving signals from the infrared remote control transmitter
2 IR Receiver Signal receiver for the infrared remote control transmitter
3 POWER LED Lights when the device is turned on
4 ALL Button Press followed by an input button to connect the selected input to all outputs
For example, press ALL and then Input button # 2 to connect input # 2 to all the outputs
5 OFF Button Press after pressing an output button to disconnect the selected output from the inputs.
To disconnect all the outputs, press ALL followed by OFF
6
SELECT Buttons
IN (1 to 8) Press to select the input to switch after selecting an output (also used for storing machine
setups (see Section 6.3)
7 OUT (1 to 8) Press to select an output to switch followed by an input (also used for storing machine setups
(see Section 6.3)
8 STO Button Press to store the current switching setting to a preset (see Section 6.3)
9 RCL Button Press to recall the current switching setting from a preset (see Section 6.3)
10 LOCK Button Press and hold to toggle the locking/release of the front panel buttons.
When storing or recalling presets, press to store or recall the preset (see Section 6.3)
11 EDID Button Press to capture the EDID (see Section 6.2)
12 OUTPUT/INPUT 7-segment LED Display Displays the input currently switched to the output which is marked above each input

6 VS-88HN - Overview
Figure 2: VS-88HN 8x8 HDMI Matrix Switcher Rear Panel
#
Feature
Function
13 IN HDMI Connectors(1 to 8) Connect to up to 8 HDMI sources
14 OUT HDMI Connectors (1 to 8) Connect to up to 8 HDMI acceptors
15 RS-232 9-pin D-sub Port Connector Connect to a PC/serial controller
16 ETHERNET RJ-45 Connector Connect to a PC via a LAN
17 ETH RESET Button Press to reset to the factory default IP parameters:
IP number −192.168.1.39
Mask – 255.255.255.0
Gateway – 192.168.1.1
Depress the button while powering on the device. The device powers up with the factory default IP parameters
18 REMOTE IR Opening Connect to an external IR receiver for controlling the device via and IR remote controller (see
Section 3.2)
Covered by a cap. The 3.5mm jack at the end of the internal IR connection cable fits into this opening
19 Mains Power Connector Connect to the mains power
20 Mains Power Fuse Fuse for protecting the device
21 Mains Power Switch Switch for turning the device on or off
6VS-88HN – Overview

VS-88HN - Overview 7
3.2 Using the IR Transmitter
You can use the RC-IR3 IR transmitter to control the machine via the built-in IR
receiver on the front panel or, instead, via an optional external IR receiver (Model:
C-A35M/IRR-50). The external IR receiver can be located up to 15 meters away
from the machine. This distance can be extended to up to 60 meters when used
with three extension cables (Model: C-A35M/A35F-50).
Before using the external IR receiver, be sure to arrange for your Kramer dealer to
insert the internal IR connection cable (P/N: 505-70434010-S) with the 3.5mm
connector that fits into the REMOTE IR opening on the rear panel. Connect the
external IR receiver to the REMOTE IR 3.5mm connector.

8 VS-88HN - Installing in a Rack
4 Installing in a Rack
This section provides instructions for rack mounting the unit.

VS-88HN - Connecting the VS-88HN 8x8 HDMI Matrix Switcher 9
5 Connecting the VS-88HN 8x8 HDMI Matrix
Switcher
Always switch off the power to each device before connecting it to your
VS-88HN. After connecting your VS-88HN, connect its power and then
switch on the power to each device.
To connect the VS-88HN 8x8 HDMI Matrix Switcher as illustrated in the
example in Figure 3:
1. Connect up to eight HDMI sources (for example, DVD players) to the IN
HDMI connectors.
You do not have to connect all the sources.
2. Connect the eight OUT HDMI connectors to up to eight HDMI acceptors (for
example, LCD displays with built-in speakers).
You do not have to connect all the outputs.
3. If required, connect a PC/controller to the RS-232 port (see Section 6.6)
and/or the Ethernet port (see Section 6.7).
4. Connect the device to the mains electricity (not shown in Figure 3).
5. If necessary, acquire the EDID (see Section 6.2)
i

10 VS-88HN - Connecting the VS-88HN 8x8 HDMI Matrix Switcher
Figure 3: Connecting the VS-88HN 8x8 HDMI Matrix Switcher

VS-88HN - Operating the VS-88HN 8x8 HDMI Matrix Switcher 11
6 Operating the VS-88HN 8x8 HDMI Matrix
Switcher
This section describes how to:
•Switch an input to an output (see Section 6.1)
•Acquire the EDID (see Section 6.2)
•Store and recall switch settings (see Section 6.3)
•Reset the VS-88HN (see Section 6.4)
•Switch between Protocol 2000 and Protocol 3000 (see Section 6.5)
•Connect to the VS-88HN via RS-232 (see Section 6.6)
•Connect to the VS-88HN via Ethernet (see Section 6.7)
•Upgrade the firmware (see Section 6.8)
6.1 Switching an Input to an Output
To switch an input to an output:
•Press an output button followed by an input button to switch the selected
input to the selected output
6.2 Acquiring the EDID
You can acquire the EDID from any of the following:
•One output set to one or more of the eight inputs (see Section 6.2.1)
•Different outputs set to different inputs (see Section 6.2.2)
•The default EDID (see Section 6.2.3)
Note: Attempting to acquire the EDID from an output that does not have a display
device connected to it results in the default EDID being acquired.

12 VS-88HN - Operating the VS-88HN 8x8 HDMI Matrix Switcher
6.2.1 Acquiring the EDID from One Output
Note: You can assign the EDID from one output to any or all of the eight inputs.
To acquire the EDID from a display device connected to one of the outputs:
1. Press the EDID and STO buttons simultaneously and hold them for 3
seconds.
Both buttons flash.
2. Press the input button to which the EDID is copied.
The selected input number flashes on the display.
3. Select the output from which the EDID is to be acquired.
4. Press the EDID button.
The EDID is stored when the display returns to normal and the EDID and
STO buttons stop flashing.
6.2.2 Acquiring the EDID from Different Outputs to Different Inputs
To acquire the EDID from several outputs (for example, OUT 1 to IN 1 and
OUT 6 to IN 3):
1. Connect the display devices to the outputs from which you want to acquire
the EDIDs.
2. Press the EDID and STO buttons simultaneously and hold them for 3
seconds.
Both buttons flash.
3. Press the input button to which the EDID is copied (for example, IN 1).
The selected input number flashes on the display.
4. Select the output from which the EDID is acquired (for example, OUT 1).
5. Press the IN 1 button.
The IN 1 button stops flashing.
6. Press the next input button to which the EDID is copied (for example, IN 3).
The selected input number flashes on the display.

VS-88HN - Operating the VS-88HN 8x8 HDMI Matrix Switcher 13
7. Select the output from which the EDID is acquired (for example, OUT 6).
8. Press the IN 3 button.
The IN 3 button stops flashing.
9. Press the input buttons to which you want to copy the EDID (for example, IN
1 and IN 3).
10. Make sure that the relevant input numbers flash on the display.
11. Press the EDID button.
The process is complete when the display returns to normal.
6.2.3 Acquiring the Default EDID
To store the default EDID on a selected input (for example, Input 2):
1. Press the EDID and STO buttons simultaneously and hold them for 3
seconds.
Both buttons flash.
2. Press the input (for example, Input 2) to which the EDID is to be copied.
The selected input number flashes on the display.
3. Press the OFF button until "0" (zero) appears on the display.
4. Press the EDID button.
The default EDID is stored on the selected input when the display returns to
normal.
6.3 Storing and Recalling a Setting
You can use the STO and RCL buttons to store up to 16 setups and then recall
them using the OUT (1-8) and IN (9-16) SELECTOR buttons (see Figure 4).
Figure 4: Store-Recall Button Configuration

14 VS-88HN - Operating the VS-88HN 8x8 HDMI Matrix Switcher
To store a preset (for example, to preset 10):
1. Configure the switching as required for the preset.
2. Press the STO button.
The STO button flashes.
3. Select an OUT or IN SELECT button to store the device setting (for example,
IN 2 for preset 10).
4. Press the STO button to store the current setup.
You have to press the LOCK button within 10 seconds or the procedure automatically
times out.
To recall a preset (for example, preset 10):
1. Press the RCL button.
The RCL button flashes.
2. Press the relevant OUT or IN button that stored the preset (for example, IN
2/preset 10).
3. Press the RCL button to recall the stored preset.
The RCL button stops flashing.
6.4 Resetting the IP Parameters
This procedure resets only the IP related parameters. All switching and
preset values remain unchanged.
To reset the IP parameters to their default values (see Section 8):
•Press and hold the ETH Reset button on the rear panel while powering up
the device
i

VS-88HN - Operating the VS-88HN 8x8 HDMI Matrix Switcher 15
6.5 Switching Between Protocol 2000 and Protocol 3000
To switch from Protocol 2000 to Protocol 3000 and vice-versa using the front
panel buttons:
•Press Output buttons 1 and 3 at the same time.
Protocol 3000 is active.
•Press Output buttons 1 and 2 at the same time.
Protocol 2000 is active.
6.6 Connecting via RS-232
You can connect to the VS-88HN via an RS-232 connection using, for example, a
PC. Note that a null-modem adapter/connection is not required.
To connect to the product via RS-232:
•Connect the RS-232 9-pin D-sub on the rear panel of the VS-88HN via a
9-wire straight cable (only pin 2 to pin 2, pin 3 to pin 3, and pin 5 to pin 5
need to be connected) to the RS-232 9-pin D-sub port on your PC
6.7 Connecting via Ethernet
You can connect the VS-88HN via the Ethernet, using a crossover cable (see
Section 6.7.1) for direct connection to the PC or a straight through cable (see
Section 6.7.2) for connection via a network hub or network router.
After connecting the Ethernet port, you have to install and configure your Ethernet Port. For
detailed instructions, see the “Ethernet Configuration (FC-11) guide.pdf” file in the technical
support section at http://www.kramerelectronics.com.
6.7.1 Connecting the Ethernet Port directly to a PC
You can connect the Ethernet port of the VS-88HN to the Ethernet port on your PC
via a crossover cable with RJ-45 connectors.
This type of connection is recommended for identification of the factory
default IP Address of the VS-88HN during the initial configuration
i

16 VS-88HN - Operating the VS-88HN 8x8 HDMI Matrix Switcher
After connecting the Ethernet port, configure your PC as follows:
1. On your desktop, right-click the My Network Places icon.
2. Select Properties.
3. Right-click Local Area Connection Properties.
4. Select Properties.
The Local Area Connection Properties window appears.
5. Select the Internet Protocol (TCP/IP) and click the Properties Button (see
Figure 5).
Figure 5: Local Area Connection Properties Window
6. Select Use the following IP Address, and fill in the details as shown in
Figure 6. You can use any IP address in the range 192.168.1.1 to
192.168.1.255 (excluding 192.168.1.39) that is provided by your IT
department.
7. Click OK.

VS-88HN - Operating the VS-88HN 8x8 HDMI Matrix Switcher 17
Figure 6: Internet Protocol (TCP/IP) Properties Window
6.7.2 Connecting the Ethernet Port via a Network Hub
You can connect the Ethernet port of the VS-88HN to the Ethernet port on a
network hub or network router, via a straight through cable with RJ-45 connectors.
6.8 Upgrading the Firmware
For instructions on upgrading the firmware see “Upgrading the VS-88HN Firmware
Using the STC Software”.