Kraus KHU100-30-18 User manual

KHU100-30/18, KHU100-32/18
Handmade Stainless Steel
Undermount Kitchen Sink
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV. July 1, 2020
R
INSTALLATION MANUAL

2
Congratulations on the purchase of your new Kraus plumbing fixture!
Please keep the box and packaging materials until your product is completely installed. If you have
any questions, require technical assistance or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your receipt with purchase date for
reference.
If for any reason this product does not meet your expectations, please be sure to repack this
product in the original box and packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP

3
For technical assistance or replacement parts, please contact Kraus Customer Service
and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
The step-by-step guidelines in the installation instructions are a general reference for installing a Kraus sink. Should
there be any discrepancies, Kraus cannot be held liable. It is recommended to install all Kraus products by hiring a
licensed professional.
Prior to Installation:
·Make sure that you have all necessary parts by checking the parts list. If
any part is missing or damaged, please contact Kraus Customer Service at
800-775-0703 for a replacement
·Inspect the sink prior to installation to make sure that it has not been
damaged or during shipping
·Use the cut-out template provided by Kraus
·Observe all plumbing and building codes according to your state
requirements
·Not recommended to be installed with laminate countertop

44
Tools you will need:
NOTE: Specialized tools may be necessary to install Kraus Stainless Steel Kitchen sinks with
countertop materials other than wood, marble or granite.
Safety Goggles Silicone Adhesive Jig Saw Phillips Screwdriver
Putty Knife Tape Measure Pencil Scissors Screwdriver
Drill
Parts List (Included)
KHU100-30/18
·Cut-out Template
·Mounting Hardware
Optional Accessories (Sold Separately)
KHU100-30/18
·Bottom Grid KBG-NST1-30
·Basket Strainer BST-1
·Sink Strainers ST-1, ST-4
KHU100-32/18
·Cut-out Template
·Mounting Hardware
KHU100-32/18
·Bottom Grid KBG-NST1-32
·Basket Strainer BST-1
·Sink Strainers ST-1, ST-4

55
Dimensions:
KHU100-30/18
30” x 18” x 10”
Min Cabinet Size: 33”
KHU100-32/18
32” x 17” x 10”
Min Cabinet Size: 36”
3 1/2"
(90mm)
18" (457.2mm)
28" (711.2mm)
30" (762mm)
10" (254mm)
R3/8"
(10mm)
10 1/2" (266mm)
26 5/8" (675.7mm)
5 1/4"
(132.6mm)
16" (406.4mm)
14 5/8" (370.9mm)
R3/8"
(10mm)
3 1/2"
(90mm)
19" (482.2mm)
30" (762mm)
32" (812.8mm)
10" (254mm)
R3/8"
(10mm)
10 1/2" (266mm)
28 5/8" (726.5mm)
5 1/4"
(132.6mm)
17" (431.8mm)
15 5/8" (396.3mm)
R3/8"
(10mm)

66
Undermount Installation
Step 1. Determine reveal type
·Use scissors to cut along the line of the paper template for your desired reveal type (Negative, Positive, or Flush
Reveal)
KRAUS Recommended Installation Type
3/8" Positive Reveal
Flush/Zero Reveal
1/8" Negative Reveal
1/8" NEGATIVE
FLUSH/ZERO REVEAL
3/8" POSITIVE
CENTERLINE

7
·Check the cut-out template against the actual sink to ensure a proper
sized cut-out.
·Place the cut-out template in the desired location on the countertop.
Step 2. Position template
Paper Template
NOTE: Make sure clearance is suitable for backsplash, faucet and plumbing for the sink.
Step 3. Trace Template
·Trace template on countertop with a pencil.
Paper Template

8
·Cut the opening in the countertop by carefully following the traced line.
Step 4. Cut countertop
NOTE: Please use the appropriate saw that best fits your countertop
material.
·Turn countertop over and align sink with countertop. Decide location
for mounting brackets.
·Mounting holes should be 1/2" from edge of sink.
Step 5. Set up mounting brackets
1/2"
(13mm)

9
·Drill 3/8" diameter x 1/2" deep hole in the countertop.
Step 6. Drill hole in countertop
·Insert anchors into drilled holes and lightly tap with a hammer until flush.
Step 7. Install anchors
3/8 1/2

10
·Use a bead of silicone (or preferred adhesive) around the rim of the
sink. Check the alignment of the sink to the cutout in the countertop.
Place sink over cutout hole and press firmly.
Step 8. Secure sink to countertop
Step 9. Attach mounting hardware
NOTE: Use acetone or rubbing alcohol to remove any excess sealant.
·Attach mounting hardware to secure bowl. Remove excess sealant
from inside lip.
·Allow sealant to set for 30 - 60 minutes.