Kraus KPF-3126 User manual

www.kraususa.com I Toll Free: 1.800.775.0703 I © 2022 Kraus USA Plumbing LLC I REV. June 8, 2022
Industrial Pull Down
Kitchen Faucet
KPF-3126
R
INSTALLATION MANUAL

2
Congratulations on the purchase of your new
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your
receipt with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP
R

3
Prior to Installation:
·Make sure you have all necessary parts by checking the diagram and parts list. If any
part is missing or damaged, please contact Kraus Customer Service at 800-775-0703
for a replacement.
·Read all instructions and safety warnings and ensure you have all tools, parts, and
equipment necessary for a safe installation.
·Turn off the hot and cold water supply at the angle stops and turn on the old faucet
to release any built up pressure. Remove existing faucet. Clean sink or countertop to
remove any debris, plumber’s putty, or silicone.
·Flush angle stops to release any debris prior to installation.
·Pre-drilled hole size requirement: 1 3/8" (min)
·Max countertop thickness: 2 3/8”
Tools Required
Adjustable Wrench Phillips Screwdriver Safety Goggles Pipe Tape Silicone Sealant
STOP
Care & Maintenance
To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
This installation manual is subject to change without further notice.
ACID
R

44
Diagram and Parts List
1. Spray Head
2. Faucet Body
3A. Rubber Washer
3B. Metal Washer
3C. Mounting Nut
3D. Mounting Screws
4. Waterlines
5. Quick Connector
6. Weight
1
6
3B
3C
3D
4
5
2
3A
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
R

55
Faucet Dimensions
Installer Tip:
Shut off main water supply before installing new faucet.
16 1/8"
(410.4mm)
9"
(228.6mm)
8 5/8"
(220.1mm)
Ø2 1/8"
(54mm)
5"
(126mm)
2 3/8"
(60mm)
6 1/8"
(156.2mm)
Ø1 3/4"
(44mm)
Ø1 1/2"
(37mm)
10 5/8"
(270mm)

66
Step 1. Remove mounting hardware
Step 2. Install faucet and mounting hardware
Remove the mounting screws
(3D), mounting nut (3C), metal
washer (3B) and rubber washer
(3A) from the mounting pipe.
Insert faucet body (2) into hole in
countertop or deck plate
assembly. Install mounting
hardware (3A, B, C & D) from
underneath the countertop.
3C
3A 3B
3D

7
Step 3. Secure mounting hardware
Adjust direction of faucet body (2)
so that handle is on right side of
faucet. Tighten mounting nut (3C)
until snug. Tighten mounting
screws (3D) to nut with Phillips
screwdriver until snug.
Step 4. Attach spray hose and counterweight
Connect spray hose to quick
connector (5) attached to supply
line. Install weight (6) on mark
where label on spray hose.
6
5

8
Step 5. Connect waterlines
Connect hot and cold copper lines
(4) to angle stops. Tighten both
ends of waterlines with a wrench
until snug. Turn on hot and cold
angle stops and check for leaks.
Step 6. Flush spray hose
Remove spray head (1) from
spray hose. Hold tip of spray hose.
Turn faucet on and let the water
run for 60 seconds to flush any
debris.
4
NOTE: Please make sure filter
washers are installed before
connecting to the main valve.

9
Step 7. Check for leaks
Check for leaks at the connections.
Retighten if necessary.

10
1
2
3
Maintenance - Cartridge Replacement
Step 1: Remove the handle button by hand.
Loosen the screw with a Phillips screwdriver.
Remove the handle and cartridge cap by
hand.
Step 2: Unscrew the locking nut with an
adjustable wrench. Remove ceramic disc
cartridge.
Step 3: Place the new cartridge in the handle
seat. Secure the cartridge with the locking
nut and assemble the handle.