Kraus KPF-1602 User manual

Single Lever Pull Out
Kitchen Faucet
INSTALLATION MANUAL
www.kraususa.com I toll free: 1.800.755.0703 I © 2013-2014 Kraus USA Inc.
KPF-1602

Congratulations on your new Kraus purchase!
We would like to take this opportunity to thank you for your business with Kraus USA.
It is our sincere hope that you are completely satised with your Kraus experience.
We welcome any questions or comments you may have, and look forward to assisting
you in the future.
For more information about Kraus products, please visit our website at:
www.kraususa.com.
In order to allow us to serve you better, we recommend registering your new Kraus
product at: www.kraususa.com/product-registration
Sincerely,
Kraus Customer Service Department
Prior to Installation
• Make sure that the cold and hot water lines are turned o
• Wrap all threaded connections with Teon tape. Always wrap in a clockwise
direction
• Cover your drain to avoid losing parts
• Do not disassemble the main faucet body, as it has been installed & commissioned
correctly & precisely before delivery from the factory
• To keep the faucet from jamming, ush the water pipe before installation
• Using condition: Working pressure at 0.05-1.0MPa (including cold & hot water
pressure) with applicable water temperature: 4C-90C
• The minimum distance between the faucet hole and the wall/backsplash is 3.5”
• The faucet hole size must be between 1-3/8” and 1-1/2”
• Check to make sure you have all included parts (page 2)
• Do not assemble parts 9 -12 until step 4

1
10
279
10 31/32”
Minimum distance 90mm
~3.5”
~3.5”
Less than 90mm
Cold Water
Hot Water
Ø35~Ø38
1
23
10
9
11
12 13
1
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
32 3/32”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 15
14
13
2
3
4
5
6
7
8
1
10
279
10 31/32”
Minimum distance 90mm
~3.5”
~3.5”
Less than 90mm
Cold Water
Hot Water
Ø35~Ø38
1
23
10
9
11
12 13
1
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
32 3/32”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 15
14
13
2
3
4
5
6
7
8
Included Parts:
1. Faucet Body
2. Base
3. Base O-Ring
4. Plastic Washer - Optional
(Top Mount Sinks Only)
5. Rubber Washer
6. Metal Washer
7. Mounting Nut
8. Mounting Screws (2)
9. Spray Head
10. Spray Hose
11. Spring
12. Sprayer Holder
13. Thumb Screws (2)
14. Hot and Cold Waterlines
15. Manual
Wrench Phillips Screwdriver
Tools you will need:
1
10
279
10 31/32”
Minimum distance 90mm
~3.5”
~3.5”
Less than 90mm
Cold Water
Hot Water
Ø35~Ø38
1
23
10
9
11
12 13
1
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
32 3/32”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 15
14
13
2
3
4
5
6
7
8
1
10
279
10 31/32”
Minimum distance 90mm
~3.5”
~3.5”
Less than 90mm
Cold Water
Hot Water
Ø35~Ø38
1
23
10
9
11
12 13
1
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
32 3/32”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12
15
14
13
2
3
4
5
6
7
8
KPF-1602 Diagram and Parts List

Dimension Drawings
1
10
279
10 31/32”
Minimum distance 90mm
~3.5”
~3.5”
Less than 90mm
Cold Water
Hot Water
Ø35~Ø38
1
23
10
9
11
12 13
1
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
32 3/32”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 15
14
13
2
3
4
5
6
7
8
Safety Tips
• If soldering the water connections when installing the faucet, remove the O-rings,
cartridges, and washers before applying any heat
• Protect your eyes with safety glasses when cutting or soldering
• Do not overtighten xing screws/nuts. Tighten nger-tight, then use a wrench/
screwdriver to tighten the xing screw/nut until snug
1
10
279
10 31/32”
Minimum distance 90mm
~3.5”
~3.5”
Less than 90mm
Cold Water
Hot Water
Ø35~Ø38
1
23
10
9
11
12 13
1
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
32 3/32”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 15
14
13
2
3
4
5
6
7
8

1
10
279
10 31/32”
Minimum distance 90mm
~3.5”
~3.5”
Less than 90mm
Cold Water
Hot Water
Ø35~Ø38
1
23
10
9
11
12 13
1
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
32 3/32”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 15
14
13
2
3
4
5
6
7
8
1
10
279
10 31/32”
Minimum distance 90mm
~3.5”
~3.5”
Less than 90mm
Cold Water
Hot Water
Ø35~Ø38
1
23
10
9
11
12 13
1
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
32 3/32”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 15
14
13
2
3
4
5
6
7
8
Installation Method 1
Installation Method 2 (optional)
When possible, the minimum
distance between the faucet hole
and the wall should be 3.5”.
If circumstances require the
distance between the faucet hole
and the wall to be less than 3.5,”
position the faucet lever 30˚ to
90˚ o the wall to allow for full
operation.
Faucet Installation Procedures

1
10
279
10 31/32”
Minimum distance 90mm
~3.5”
~3.5”
Less than 90mm
Cold Water
Hot Water
Ø35~Ø38
1
23
10
9
11
12 13
1
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
32 3/32”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 15
14
13
2
3
4
5
6
7
8
1
10
279
10 31/32”
Minimum distance 90mm
~3.5”
~3.5”
Less than 90mm
Cold Water
Hot Water
Ø35~Ø38
1
23
10
9
11
12 13
1
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
32 3/32”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 15
14
13
2
3
4
5
6
7
8
Step 1
Step 2
Remove the mounting screws
(8), mounting nut (7), metal
washer (6), rubber washer (5),
and plastic washer (4) from
the main faucet (1). The base
(2) and base O-ring (3) should
remain on the faucet body.
Insert faucet body into the hole
on the deck with the base (2)
and base O-ring (3) attached,
then install plastic washer
(4), rubber washer (5), metal
washer (6), mounting nut (7),
and mounting screws (8) from
underneath the sink.

1
10
279
10 31/32”
Minimum distance 90mm
~3.5”
~3.5”
Less than 90mm
Cold Water
Hot Water
Ø35~Ø38
1
23
10
9
11
12 13
1
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
32 3/32”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 15
14
13
2
3
4
5
6
7
8
1
10
279
10 31/32”
Minimum distance 90mm
~3.5”
~3.5”
Less than 90mm
Cold Water
Hot Water
Ø35~Ø38
1
23
10
9
11
12 13
1
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
32 3/32”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 15
14
13
2
3
4
5
6
7
8
Step 3
Step 4
After adjusting the direction
of the faucet body (1), tighten
the mounting nut (7) until snug
and tighten the mounting
screws (8) to the nut with a
Phillips head screwdriver until
snug.
Situate the sprayer holder (12)
onto the faucet body (1), then
connect the sprayer hose (10) to
the faucet body (1) and nger
tighten.

Step 6
1
10
279
10 31/32”
Minimum distance 90mm
~3.5”
~3.5”
Less than 90mm
Cold Water
Hot Water
Ø35~Ø38
1
23
10
9
11
12 13
1
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
32 3/32”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 15
14
13
2
3
4
5
6
7
8
Connect and tighten hot and
cold waterlines (14) to the
angle stops and tighten with a
wrench until snug. Turn on the
water supplies and check for
leaks.
Installer Tip
If facing faucet, the hot water
connector is to the left & cold
water connector is to the right.
1
10
279
10 31/32”
Minimum distance 90mm
~3.5”
~3.5”
Less than 90mm
Cold Water
Hot Water
Ø35~Ø38
1
23
10
9
11
12 13
1
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
32 3/32”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 15
14
13
2
3
4
5
6
7
8
Step 5
Tighten the hexagon nut of
sprayer hose (10) with a wrench
until snug. Insert the spring
(11) into sprayer holder (12).
After adjusting the direction
of sprayer holder (12) to the
desired location, tighten
thumb screws (13). Connect
sprayer (9) to the sprayer
hose (10); nger-tighten, then
tighten with wrench until snug.

Usage
Sprayer:
How to operate the handle:
1. Raise the lever handle to turn on
the water. Push down to turn o.
2. Turn the lever handle to the left
to increase hot water ow, turn
to the right to increase cold ow.
1. To activate sprayer, turn on
water with lever and squeeze
sprayer.
Care & Maintenance
*To keep the product clean & shining, follow the
steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners
3. Do not use a cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
*This installation manual is subject to change without further notice.
1
10
279
10 31/32”
Minimum distance 90mm
~3.5”
~3.5”
Less than 90mm
Cold Water
Hot Water
Ø35~Ø38
1
23
10
9
11
12 13
1
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
32 3/32”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 15
14
13
2
3
4
5
6
7
8
1
10
279
10 31/32”
Minimum distance 90mm
~3.5”
~3.5”
Less than 90mm
Cold Water
Hot Water
Ø35~Ø38
1
23
10
9
11
12 13
1
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
32 3/32”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 15
14
13
2
3
4
5
6
7
8
1
10
279
10 31/32”
Minimum distance 90mm
~3.5”
~3.5”
Less than 90mm
Cold Water
Hot Water
Ø35~Ø38
1
23
10
9
11
12 13
1
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
32 3/32”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 15
14
13
2
3
4
5
6
7
8

Trouble - Shooting
If you have followed the instructions carefully and your faucet still does not
work properly, take the following corrective steps:
PROBLEM CAUSE ACTION
Leakage under the
handle
Locking nut has come
loose
Unscrew the lever on
the handle by hand.
Loosen set screw
with a hex wrench.
Remove the handle and
unscrew trim cap by
hand. Tighten locking
nut with an adjustable
wrench
Aerator drips or has
inconsistent water flow
pattern
Aerator is dirty or not
seated properly
Unscrew aerator by
hand and clean out
debris
Water will not shut off
completely
Cartridge may be
defective
Unscrew the lever on
the handle by hand.
Loosen set screw with
a hex wrench (2.5 mm).
Remove the handle
and unscrew trim cap
by hand. Unscrew the
locking nut with an
adjustable wrench.
Remove ceramic disc
cartridge. Check for
cracks
Leaking between hose
and faucet body or
spray head
Hose may be loose or
washers are not seated
correctly in the hose
connections
Tighten the hexagon
nut with a wrench and
make sure the washers
are seated correctly