Kraus Turino KFR1-33GWH User manual

www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV. October 29, 2020
Fireclay Farmhouse
Kitchen Sink
KFR1-33GWH / KFR1-MWH /
KFR1-MGR
R
INSTALLATION MANUAL

Thank you for your purchase
We would like to take this opportunity to thank you for choosing Kraus.
We hope that you are completely satisfied with your purchase, and enjoy it for years to
come. If you have any questions, or require technical assistance, please contact us at
800.775.0703 and one of our representatives will be happy to help.
For more information about Kraus products, please visit:
www.kraususa.com
In order to activate your warranty and get faster access to customer support, please
register your new Kraus product at:
www.kraususa.com/registration
Sincerely,
Kraus USA Customer Service
2

3
Prior to Installation:
·Inspect the sink prior to installation to make sure the sink has not been damaged
during shipping.
·Observe all plumbing and building codes according to your state requirements.
·Additional floor and wall preparation may be required to avoid damaging the sink.
·Make sure to purchase the correct cabinet for your farmhouse sink. Farmhouse
base cabinets should be 3" larger than the actual size of the sink.
·Not recommended to be installed with laminate countertop.
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
The step-by-step guidelines in the installation instructions are a general reference for
installing a Kraus Sink. Should there be any discrepancies, Kraus cannot be held liable. It is
recommended to install all Kraus products by hiring a licensed professional.

Tools you will need:
4
Parts List
·Sink
·Bottom Grid
NOTE: Specialized tools may be necessary to install Kraus Fireclay sinks with
countertop materials other than wood, marble or granite.
Phillips Screwdriver Pencil
Tape Measure Screwdriver Level
Safety Goggles Silicone Adhesive Jig Saw AcetoneDrill
33"
838mm
18 1/4"
465mm
30 1/4"
768mm
32 1/4"
820mm
10"
254mm
Dimensions
KFR1-33
33" x 18 1/4" x 10"
ACETONE
88° 88°

5
1. Measure & Build Supports
·Measure the actual height of apron
·Build supports on inside of cabinet based on sink measurements
Installer Tip: Support options
·1 1/4" Angle Irons
·(2) 2" x 4'
·3/4" Plywood
SUPPORTS
NOTE: Due to the typical ±3mm side
wall variance in manufacturing, it is
recommended that you design /
modify the sink cabinet to match your
clients individual sink(s) need.

6
2. Cut Cabinet Front
·Measure height of apron front. Add 1
16" to the dimension when you mark
base cabinet front cutout. Use jigsaw to cut.

7
3. Install Sink
·Place sink in opening. The weight of sink should be sustained
by the built supports.
·Make sure sink is leveled from front to back and side to side
·Uses silicone to fill in gaps where necessary
NOTE: This sink is reversible. Pick which apron you'd like facing forward before
installing.
Kraus

8
4. Cut Countertop
·Due to the custom nature of this type of installation, no cutout template is
included.
·Kraus recommends providing the cabinet maker with the actual sink to
be installed prior to the cabinet fabrication.
·It is recommended that the sink be installed with an approximately 1/8"
positive reveal. It is further recommended that the installer(s) discuss this
with the customer and agree that this finished appearance is the desired
effect.
Kraus

9
Installer Tip: Use acetone or denatured alcohol to remove any excess sealant.
5. Install Countertop
·Use a bead of silicone (or preferred adhesive) around the rim of the sink.
Check the alignment of the sink to the cutout in the countertop. Place
countertop cutout hole over sink and press firmly.
Silicone Adhesive
Kraus

10
6. Installing Plumbing and Fixtures
·Connect drain, trap to drain and water supply connections to the faucet
according to manufacturer's instruction.
·Run water into sink and check for leaks.
·Note: Before installation, please check that the drain kit complies with
ASME A112.18.2/CSA B125.2 and with CUPC certification.
Kraus