Kraus Oletto KPF-3101MB User manual

www.kraususa.com I Toll Free: 1.800.775.0703 I © 2022 Kraus USA Plumbing LLC I REV. April 11, 2022
OlettoTM Pull Down Kitchen Faucet
KPF-3101
R
INSTALLATION MANUAL

Congratulations on the purchase of your new
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your
receipt with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP
2
R

3
Prior to Installation:
·Make sure you have all necessary parts by checking the diagram and parts list. If any
part is missing or damaged, please contact Kraus Customer Service at 800-775-0703
for a replacement.
·Read all instructions and safety warnings and ensure you have all tools, parts, and
equipment necessary for a safe installation.
·Turn off the hot and cold water supply at the angle stops and turn on the old faucet
to release any built up pressure. Remove existing faucet. Clean sink or countertop to
remove any debris, plumber’s putty, or silicone.
·Flush angle stops to release any debris prior to installation.
·Pre-drilled hole size requirement: 1 3/8" (min)
·Max countertop thickness: 1 3/4”
Tools Required
Adjustable Wrench Phillips Screwdriver Safety Goggles Pipe Tape Silicone Sealant
STOP
Care & Maintenance
To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
This installation manual is subject to change without further notice.
ACID
R

4
Diagram and Parts List
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
A. Faucet Body
B. Mounting Hardware
1. Rubber & Metal Washer
2. Mounting Nut
3. Mounting Screws
C. Weight
D. Hex Key
E. Base Seat Assembly
A
D
C
B1
B2
B3
E
R

Installer Tip:
Shut off main water supply before installing new faucet. 5
10 1/4"
(260mm)
19 3/4"
(501mm)
10 1/2"
(266mm)
3 1/2"
(90mm)
1 3/4"
(45mm)
7 7/8"
(200mm)
4 3/8"
(112mm)
8 3/4"
(221mm)
2 1/8"
(52.5mm)
21 3/8"
(544mm)
Faucet Dimension
8 5/8"
(219mm)

Step 1. Installing the faucet assembly
Step 2. Securing the faucet assembly
Insert all the hoses through the
Base Seat Assembly (E).
Insert the faucet body through the
hole in the sink or countertop.
Install the rubber washer and
metal washer (B1) onto the
threaded mounting shank.
Thread the nut (B2) onto the
mounting shank. Lock the nut (B2)
into position by tightening the
screws (B3). Do not overtighten.
B1
B2 B3
6
E

Step 3. Securing the faucet assembly
Push the quick connector (1)
firmly upward and attach it to the
receiving block (2). Pull down
moderately to ensure the
connection has been made.
Step 4. Attach the counterweight
Install the weight (C) on the
marked area of the spray hose.
2
1
7
C
Marked Area

Step 5. Making the waterline connections
Step 6. Flushing and checking for leaks
Thread the nut (1) on the supply
line onto the outlet of the water
supply valve and tighten with a
wrench. Do not overtighten.
Pull the hose assembly out of the
spout and remove the spray head
by unscrewing it from the hose in
a counterclockwise direction. Be
sure to hold the end of the hose
down into the sink and turn the
faucet on to the warm position
where it mixes hot and cold water.
Flush the water lines for one
minute. This flushes away any
debris that could cause damage
to internal parts. Check for leaks.
Re-tighten any connections if
necessary, but do not overtighten.
Reinstall the spray head by hand
tightening it back onto the spray
hose. After installation is
completed, turn on the hot and
cold water supplies. Check for
leaks.
1
8
NOTE: Please make sure filter
washers are installed before
connecting to the main valve.

Replacement Parts
Replacement Parts List Finish/Color Part #
KP46002
KP46025
KP46001
1. Sprayer Head
2. Check Valve
3. Sprayer Hose
4. Handle Assembly
5. Cartridge Cover
7. Cartridge
6. Locking Nut
8. Base Seat Assembly
9. Rubber Washer
10. Metal Washer
11. Mounting Nut
13. 1.8GPM Flow Restrictor
14. Quick Connector
15. EZ-Weight
*Denotes faucet component color options:
CH - Chrome
SFS - Spot Free Stainless Steel
MB - Matte Black
BG - Brushed Gold
WH - White
CH,SFS,MB,BG*
KP46015
KP46022
KP46013
KP46012
KP46021
KP46004
KP46006
12. Mounting Screw
16. Filter Washer
17. Hex Key
BL - Black
CH,SFS,MB,BG*
CH,SFS,MB,BG*
CH,SFS,MB,BG*
CH,SFS,MB,BG*
WH*
KP46007
KP46008
KP46011
KP46010
KP46009
KP46017
1
2
17
KP46024
3
4
5
6
7
8
9
10
11
12
14
13
15
16
18. Mounting Hardware Kit
(includes KP46004,KP46006,
KP46007,KP46008)
KP46038
18
9

Troubleshooting
If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps:
Leakage under faucet handle Locking nut has come loose or
cartridge needs to be reseated.
Remove button located at top of handle.
Loosen set screw with hex wrench. Remove
handle and unscrew cartridge cover by
hand. Tighten locking nut with an
adjustable wrench.
Leaking between spray head
and the hose
Spray head may be loose or
washer is not seated correctly
in the hose connection.
Tighten spray head by hand until snug.
Make sure washer is seated correctly.
Water does not shut off
completely
Cartridge may need to be
adjusted or replaced.
Remove button located at top of handle.
Loosen set screw with hex wrench. Remove
handle and unscrew cartridge cover by
hand. Unscrew locking nut with an
adjustable wrench. Remove ceramic disc
cartridge.
Check for cracks, and if O-ring is seated
correctly. Reseat cartridge.
Hose does not retract Weight may be installed
incorrectly.
Readjust weight on hose.
Low flow Aerator may be clogged Unscrew aerator with aerator key. Hold tip
of spray head and turn on water to flush
debris.
The screen filter in the hose
connectors is dirty.
Turn off the water supply at water valve
and unscrew the hose connectors from
water supply lines. Clean the screen in the
water lines with hot water, removing any
debris or calcium build up.
PROBLEM CAUSE ACTION
10