Kraus KPF-1622 User manual

INSTALLATION MANUAL
Single Lever Pull-Out
Kitchen Mixer
KPF-1622
www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc. I REV. August 16, 2016

2
PRIOR TO INSTALLATION
• Make sure you have all necessary parts by checking the diagram and parts
list. If any part is missing or damaged, please contact Kraus Customer
Service at 800-775-0703 for a replacement
• Turn o the hot and cold water supply at the angle stops and turn on the
old faucet to release any built up pressure. Remove existing faucet. Clean
sink or countertop to remove any debris, plumber’s putty, or silicone
• Place bucket under angle stops. Turn on to ush any debris prior to
installing new plumbing. Shut o angle stops
• Pre-drilled hole size requirement: 1-3/8”
• Max countertop thickness without deck plate: 1-3/8”
Tools Required
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [e-mail]
Adjustable Wrench
6 5/8”
5 4/5”
3/8”
(10mm)
7/8”
19.7º(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
3 3/4”
(168mm)
(147.3mm)
(96mm)
∅ 1 3/4”
(∅ 45mm)
∅ 1 15/16”
(∅ 50mm)
9/16”-18UNEF
27mm ~ 41.3mm 1 1/16” ~ 1 5/8”
∅ 1 15/16”
(∅ 50mm)
12 7/16”
(316mm)
1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
Silicone Sealant
6 5/8”
5 4/5”
3/8”
(10mm)
7/8”
19.7º(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
3 3/4”
(168mm)
(147.3mm)
(96mm)
∅ 1 3/4”
(∅ 45mm)
∅ 1 15/16”
(∅ 50mm)
9/16”-18UNEF
27mm ~ 41.3mm 1 1/16” ~ 1 5/8”
∅ 1 15/16”
(∅ 50mm)
12 7/16”
(316mm)
1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
Phillips Screwdriver Safety Goggles Bucket

3
Diagram and Parts List
A. Faucet Body
B. Aerator Head
C. Base
D. Base O-Ring
E. Mounting Hardware Assembly
E1 Rubber& Metal Washer
E2 Mounting Nut
E3 Mounting Screws
F. Weight
G. Hot & Cold Waterlines
H. Spray Hose
I. Spacer
J. Check Valve
Included Parts:
1. Faucet Body
2. Aerator Head
3. Base
4. Base O-Ring
5. Rubber Washer
6. Mounting Nut
7. Mounting Screws
8. Weight
9. Hot & Cold Waterlines
10. Spray Hose
11. Spacer
KPF-1622 Diagram and Parts List
2
Aerator
Pull Out Hose
14 3/4”
1
3
4
5
6
7
810
11
9
Wrench Phillips Screwdriver
Tools you will need:
3
2
Aerator
Pull Out Hose
14 3/4”
1
4
5
6
7
8
9
10 12
13
11
3
2
Aerator
14 3/4”
1
4
5
6
7
8
9
10 12
13
11
12
12. Check Valve
A
B
D
C
E1
E2
E3
F
G
H
I
J

4
Faucet Dimensions
7”
(179 mm)
12°
8 -1/4”
(209 mm)
9 -3/8”
(239 mm)
6 -7/8”
(175 mm)
5-3/8”
(135 mm)
2 -5/8”
(66 mm)
14 -7/8”
(377 mm)
2 -1/8”
(53 mm)
360°

5
Faucet Dimensions
Faucet Installation Methods
Installation Method 1
Installation Method 2
The minimum distance between
the faucet hole and wall should
be 3.5”
If the distance between the
faucet hole and the wall is less
than 3.5”, position the faucet
lever 30 degrees to 90 degrees
off the wall to allow for full
operation
1. Remove mounting screws (9), mounting nut (8), metal washer (7),
and rubber washer (6) from the faucet body (1).
Minimum distance 3.5
Less than
Ø35~Ø38
Ø1 ~Ø1
Step 1
1
6
7
8
9
1. Remove mounting screws (9), mounting nut (8), metal washer (7),
and rubber washer (6) from the faucet body (1).
Minimum distance 3.5
Less than
Ø35~Ø38
Ø1 ~Ø1
Step 1
1
6
7
8
9
7”
(179 mm)
12°
8 -1/4”
(209 mm)
9 -3/8”
(239 mm)
6 -7/8”
(175 mm)
5-3/8”
(135 mm)
2 -5/8”
(66 mm)
14 -7/8”
(377 mm)
2 -1/8”
(53 mm)
360°

6
Faucet Installation Methods
Installation Method 1
Installation Method 2
The minimum distance between
the faucet hole and wall should
be 3.5”
If the distance between the
faucet hole and the wall is less
than 3.5”, position the faucet
lever 30 degrees to 90 degrees
off the wall to allow for full
operation
1. Remove mounting screws (9), mounting nut (8), metal washer (7),
and rubber washer (6) from the faucet body (1).
Minimum distance 3.5
Less than
Ø35~Ø38
Ø1 ~Ø1
Step 1
1
6
7
8
9
1. Remove mounting screws (9), mounting nut (8), metal washer (7),
and rubber washer (6) from the faucet body (1).
Minimum distance 3.5
Less than
Ø35~Ø38
Ø1 ~Ø1
Step 1
1
6
7
8
9

7
Step 1
1. Remove mounting screws (9), mounting nut (8), metal washer (7),
and rubber washer (6) from the faucet body (1).
Ø35~Ø38
Ø1 ~Ø1
Step 1
1
Installation Steps
Step 2
t the faucet body (1) into the hole on the deck with the base
(4) and base o-ring (5), and then install the rubber washer (6),
metal washer (7), mounting nut (8) and mounting screws (9) from
underneath the sink.
1
8
Step 3
2. Insert the faucet body (1) into the hole on the deck with the base
(4) and base o-ring (5), and then install the rubber washer (6),
metal washer (7), mounting nut (8) and mounting screws (9) from
underneath the sink.
4
5
6
7
8
9
3. After adjusting the direction of the faucet body (1), tighten the
mounting nut (8) until snug and tighten the mounting screws (9) to
Step 4
Step 3
Remove mounting hardware
assembly (E)
Connect waterlines (G) to hot and
cold copper lines on faucet
E1
E2
E3
9
Step 6
Hot
Water
Cold
Water
Installer Tip
F
E
G
F
Hexagon Nut
Hot
Water
Cold
Water
Close
Open Left
Hot Water
Push
25˚ 90˚
Step 5
KPF-1602.indd 9 2016-08-09 3:39 PM
A
J
Use two wrenches when
securing waterlines (G) to
copper lines to prevent kinking,
as shown in picture

8
Step 1
1. Remove mounting screws (9), mounting nut (8), metal washer (7),
and rubber washer (6) from the faucet body (1).
Ø35~Ø38
Ø1 ~Ø1
Step 1
1
Installation Steps
Step 2
t the faucet body (1) into the hole on the deck with the base
(4) and base o-ring (5), and then install the rubber washer (6),
metal washer (7), mounting nut (8) and mounting screws (9) from
underneath the sink.
1
8
Step 3
2. Insert the faucet body (1) into the hole on the deck with the base
(4) and base o-ring (5), and then install the rubber washer (6),
metal washer (7), mounting nut (8) and mounting screws (9) from
underneath the sink.
4
5
6
7
8
9
3. After adjusting the direction of the faucet body (1), tighten the
mounting nut (8) until snug and tighten the mounting screws (9) to
Step 4
Step 3
Insert faucet body (A) into hole
on deck or sink with base (C) and
base o-ring (D) attached. Attach
mounting hardware assembly (E)
Adjust faucet body (A). Secure
mounting hardware (E) with
wrench and Phillips head
screwdriver
E1
C
D
E2
E3
A
A
E
9
Step 6
Hot
Water
Cold
Water
Installer Tip
F
E
G
F
Hexagon Nut
Hot
Water
Cold
Water
Close
Open Left
Hot Water
Push
25˚ 90˚
Step 5
KPF-1602.indd 9 2016-08-09 3:39 PM
A
J

9
Step 5
Step 6
Step 4
4. Connect the spray h
with a wrench until snug
hose (12). Connect h
and tighten with a wrench, then turn on water supplies and check
leaks.
3
2
Aerator
Pull Out Hose
8 1/2”
25˚
Close
Open
110˚
Left
Hot Water
Right
Cold Water
Swiveling Range
360˚
7”
14 3/4”
360˚
1
4
5
6
7
8
9
10 12
13
11
1. Pull the lever to the right to
turn on the water. Push to the
left to turn off
2. Pull the lever forward to
increase hot water flow and
push the lever back to increase
the cold water flow
3
2
Aerator
Pull Out Hose
8 1/2”
25˚
Close
Open
110˚
Left
Hot Water
Right
Cold Water
Swiveling Range
360˚
7”
14 3/4”
360˚
1
4
5
6
7
8
9
10 12
13
11
Usage
How to Operate the Handle
Connect spray hose (H) to check valve (J) and
tighten with an adjustable wrench.
9
Step 6
Hot
Water
Cold
Water
Installer Tip
F
E
G
F
Hexagon Nut
Hot
Water
Cold
Water
Close
Open Left
Hot Water
Push
25˚ 90˚
Step 5
KPF-1602.indd 9 2016-08-09 3:39 PM
A
J
Insert washer
Step 5
Step 6
Step 4
4. Connect the spray h
with a wrench until snug
hose (12). Connect h
and tighten with a wrench, then turn on water supplies and check
leaks.
Step 5
Step 6
Step 4
4. Connect the spray h
with a wrench until snug
hose (12). Connect h
and tighten with a wrench, then turn on water supplies and check
leaks.
Attach weight (F) to lowest point
vertically on spray hose (H)
Connect and tighten waterlines (G)
to angle stops. Turn on the angle
stops and check for leaks
(DO NOT TURN FAUCET ON)
Step 5
Step 6
Step 4
4. Connect the spray h
with a wrench until snug
hose (12). Connect h
and tighten with a wrench, then turn on water supplies and check
leaks.
Installer Tip
Remove aerator and turn faucet on
for 60 seconds to flush any debris
F
H
J
A

10
Step 5
Step 6
Step 4
4. Connect the spray h
with a wrench until snug
hose (12). Connect h
and tighten with a wrench, then turn on water supplies and check
leaks.
3
2
Aerator
Pull Out Hose
8 1/2”
25˚
Close
Open
110˚
Left
Hot Water
Right
Cold Water
Swiveling Range
360˚
7”
14 3/4”
360˚
1
4
5
6
7
8
9
10 12
13
11
1. Pull the lever to the right to
turn on the water. Push to the
left to turn off
2. Pull the lever forward to
increase hot water flow and
push the lever back to increase
the cold water flow
3
2
Aerator
Pull Out Hose
8 1/2”
25˚
Close
Open
110˚
Left
Hot Water
Right
Cold Water
Swiveling Range
360˚
7”
14 3/4”
360˚
1
4
5
6
7
8
9
10 12
13
11
Usage
How to Operate the Handle
9
Step 6
Hot
Water
Cold
Water
Installer Tip
F
E
G
F
Hexagon Nut
Hot
Water
Cold
Water
Close
Open Left
Hot Water
Push
25˚ 90˚
Step 5
KPF-1602.indd 9 2016-08-09 3:39 PM
A
J
Step 5
Step 6
Step 4
4. Connect the spray h
with a wrench until snug
hose (12). Connect h
and tighten with a wrench, then turn on water supplies and check
leaks.
Step 5
Step 6
Step 4
4. Connect the spray h
with a wrench until snug
hose (12). Connect h
and tighten with a wrench, then turn on water supplies and check
leaks.

11
Replacement Parts
1. Aerator Assembly
2. Hose
3. Aerator Head
4. Set Screw
5. Cap
6. Set Screw
7. Cap
8. Handle
9. Cartridge Cover
10. Locking Nut
11. Cartridge
12. Base
13. Base O-Ring
14. Rubber & Metal Washer
15. Mounting Nut
16. Mounting Screw
17. Protective Sleeve
18. Weight
19. Check Valves
20. Connector
21. Washer
22. Hot & Cold Waterlines
23. Hex Wrenches 2mm &
2.5mm
24. Spacer (Optional)
4
8
3
1c
1b
1a
11
10 9
7
6
19
20
18
14
16
5
12
24
2
13
15
17
21
22
23

12
Water will not shut off
completely
Cartridge (11 ) may be
defective
Remove cap (7) at
bottom of handle (8).
Loosen set screw (6)
with 2.5mm hex wrench
(23). Remove the
handle (8) and unscrew
cartridge cover (9)
by hand. Unscrew
locking nut (10) with
an adjustable wrench.
Remove ceramic disc
cartridge. Check for
cracks
Aerator (1) drips or has
inconsistent water
flow pattern
Aerator (1) is dirty or
not seated properly
Unscrew aerator (1)
by hand and clean out
debris
Trouble - Shooting
If you have followed the instructions carefully and your faucet still does not work
properly, take the following corrective steps:
PROBLEM CAUSE ACTION
Leakage under handle
(8)
Locking nut (10) has
come loose
Remove cap (7) at
bottom of handle (8).
Loosen set screw (6)
with 2.5mm hex wrench
(23). Remove the
handle (8) and unscrew
cartridge cover (9) by
hand. Tighten locking
nut (10) with an
adjustable wrench

13
Codes/Standards Applicable:
Meets ASME A112.18.1M/A112.18.1
1.5gpm 5.7L/min maximum
GREEN
Water Eciency
LEAD FREE
IAPMOR&T
TM
HELP LINE
Our customer service hours are Monday – Friday, 9am – 8pm EST.
Be sure to visit our website at www.kraususa.com
If you are a homeowner please contact a Kraus Customer Service Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
Toll-free 800-775-0703
[e-mail]
If you are a plumbing contractor or trade professional please contact a Kraus Pro
Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8955
[e-mail]
If you are an Authorized Partner please contact a Partner Support Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8954
[e-mail]
In requesting warranty service, please be ready to provide:
1. Proof of purchase.
2. A description of the problem.
NSF/ANSI Standard 61 certied by IAPMO
NSF/ANSI Standard 372 certied by IAPMO

14
www.kraususa.com
Care & Maintenance
*To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
*This installation manual is subject to change without further notice.
1
10
279
10 31/32”
Minimum distance 90mm
Less than 90mm
Cold Water
32 3/32”
Ø35~Ø38
1
23
10
9
11
12 13
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 13
2
3
4
5
6
7
8
Download the Kraus Care & Maintenance Guide at:
http://www.kraususa.com/maintenance