KREZ P3D User manual

KREZ P3D 3D pen
User Manual
Thank you for using this product, in order to operate the equipment better, please read
this manual carefully.

Parts in package
1. AC/DC adapter 2.Filament 3.user manual 4.3D pen

Warning!
1. this equipment is suitable for children over 8 years old and adult.Children is only
allowed to use under adult guardianship
2. the nozzle is with high temperature ,do not touch it by hand
3. it is strictly prohibited to input any other material into the filament loading hole
4. prohibited to use the power adapter provided by other company
5. prohibited to use the filament provided by other company,cause different parameter of
filament
6. keep the pen away from water
7. keep the pen in a safe place ,where the children can not reach
Operation instructions
1.connect AC/DC adapter to AC power socket and 3D pen DC power socket, when the LCD
screen and red light are powered on ,it means power connected
2.press the filament loading button,it starts to heat,then the screen will display the
temperature,and the green light will flash ,when it reaches the preset temperature ,
the green light will stop flashing,it means it is ready for loading filament
3.insert the 1.75mm filament into the "filament loading hole",Keep pressing the "filament
loading button",the material will be loaded . Hold till plastic material
comes out from the nozzle ,it means the filament is ready.(press the button twice can load the
filament automatically, press the button again to exit automatic mode)
4.temperature adjustment:press the temperature increase and decrease button to adjust the
temperature,temperature range is 60°C-230°C
5.speed adjustment :press the speed increase and decrease button to adjust temperature,totally 6
levels(the LCD screen will display the current speed level )

6 unload filament:do as the Item 2,then press unload filament button ,the filament will move out
(double click the button to unload filament automatically)
7.press temperature increase button and unload filament button at the same time to switch
ABS/PLA mode
8. replace nozzle set:remove the screw on the top, open the cover ,then pull out the nozzle ,
9. the pen will enter standby mode after 2 minutes no operation,and press the loading filament
button to wake it up.
10.do not touch the nozzle during working
Note
1.Heating time may be affected by environmental temperature
2.The filament end should be cut correctly before loading
3.Recommend to unload the filament after finish drawing
Trouble shooting
please follow the below instruction in case of any defect
default
reason
solution
Screen can not be powered
on
The power adapter or plug cord
defective
Repair or replace the power adapter
Motherboard defective
Repair or replace the motherboard
Socket lead off
sold the socket
No filament come out
from nozzle
Nozzle blocked
Replace the nozzle set
Temperature is not high enough
Replace the nozzle set or adjust the temperature
No working temperature
Replace the nozzle set or check the motherboard
Gear slips
Back wire, cleaning gear, cut off the damaged
supplies after the re loading
fail to load filament
unload filament and cut the end of filament well
Motherboard defective
Repair or replace the motherboard
No working temperature
Heating part defective
Replace the nozzle set

Filament cut
Specifications and parameters
Discharging mode: hot melt extrusion molding
Molding: three-dimensional molding
Print range: Unlimited
Feeding speed: adjustable
Printing material: PLA, ABS
Electric parameter: DC9V 2A 18W
The nozzle diameter: 0.6mm
Filament diameter: 1.75mm
Filament temperature: ABS230℃,PLA190℃
Power adapter electric parameter: 100-240V 50/60HZ 2A
Equipment dimension: 188mm*42mm*29mm
Equipment net weight: 65g
Features:
·LCD display can directly show the information like filament type, temperature, more humanized
display interface.
·support direct shift between PLAand ABS
·Max working current is 2A, lower energy consumption
·Human engineering design,fashion design
·double click to load and unload filament automatically
correct
Wrong
Wrong