Krix Hemispherix AS User manual

Installation Guide
Hemispherix AS

before you begin
Please read the disclaimer on the back
of this manual.
• Discuss with your local Krix distributor, or
installation consultant, to determine the
best location for your loudspeakers. Be
sure to check for any obstructions, such as
electrical wiring, plumbing, stud work or
air conditioning ducts before commencing
the installation. (figure 1)
figure 1
• Also ensure that there is enough ceiling
space to accommodate the speaker
enclosure.
connecting
To ensure optimum performance it is
important that your speaker system is
connected properly:
Turn off all electronic equipment and
disconnect from the power point.
• Follow the connection instructions
supplied with your amplifier, CD/DVD, hard
disk recorder, video player etc.
• Install speaker cable in wall or ceiling
cavity, or run cable along wall surface.
Allow approximately 300mm of excess
cable to facilitate loudspeaker installation.
• Follow the connection instructions
supplied with your amplifier to connect
the speaker cables to amplifier. Take care
to assign the same cable colour or trace to
the positive (+) connector on the amplifier
as the positive (+) connector on the
speaker.
• Prepare speaker cables for connecting to
speakers by neatly stripping cable ends.
Care should be taken to eliminate loose
strands of wire that may be present a
short circuit hazard.
Congratulations on choosing Krix
Your Krix speakers are designed to reproduce the highest quality sound. To get the best
performance from your speakers please read these installation instructions thoroughly as there
are many factors that influence the performance of your speakers. If you have any difficulties
please contact one of our friendly authorised Krix dealers.
!
installation
• Once the correct placement of the
speakers has been determined, use the
cardboard insert marked ‘template’ (from
the internal packing) to trace the required
cut-out onto the ceiling/wall. (figure 2)
• Drill a hole inside the marked cut-out.
Using a fine gyprock saw, cut around the
inside of the marked cut-out. (figure 3)
• Remove the circular offcut and insert the
speaker to check the hole is the correct
size. Enlarge the cut-out if required.
• Pull the stripped speaker cable through
the ceiling opening. Push and hold down
the positive (+) red binding post on the
speaker and insert the positive (+) wire
through hole in post. Take care to assign
the same cable colour or trace to the
positive (+) connector on the amplifier, as
the positive (+) connector on the speaker.
Repeat connection process with the
negative (-) black binding post and the
negative (-) wire. (Figure 4)
• Ensure all mounting clamps are swung
back against the speaker enclosure
(Figure 4), so that the speaker can be
easily inserted into the ceiling cut-out.
Once the speaker has been located in the
ceiling/wall, use a Philips head screwdriver
to tighten all mounting screws. As the
screws are tightened, the mounting
clamps will automatically swing out over
the gyprock and clamp the speaker in
place. Be careful not to over tighten the
screws, as this may strip the clamp, or
crush the gyprock surface. (Figure 5)
• The Hemispherix AS features a pivoting
tweeter which allows the high frequency
sound to be directed as desired, depending
on your environment and preference.
Gently press on the round outer edge
of the tweeter frame to tilt the tweeter
to the desired position. Be careful not
touch the tweeter diaphragm, as this may
damage to the tweeter. (Figure 6)
• Gently fit the magnetic grille to the front
of the speaker housing. (Figure 7)
installation
If the grille requires painting it is
recommended that the grille is painted
attached to the speaker after installation.
Use a small foam roller with a light
coverage of thin paint to avoiding
blocking the holes in the grille.
2
!
!
!
!
!

figure 4
figure 7figure 6
figure 5
installation
3
figure 3 figure 2

krix.com
Krix Loudspeakers Pty Ltd
14 Chapman Road
Hackham SA 5163
Australia
T 61 8 8384 3433
F 61 8 8384 3419
[email protected] Rev #10006
disclaimer
Cutting or drilling into anything can be dangerous. You should make sure you know what is behind or inside the surface that you are cutting
into before you start to cut. For example, you might strike an electrical cable.
If you do not feel entirely confident about installing this product, contact a professional installer.
disclaimer
To the extent permissible by law:
All warranties, conditions, representations, promises and statements relating howsoever to this product whether express or implied and
whether in contract or tort are excluded to the extent permitted by law; and
Our liability to you under a condition or warranty (if any) implied into this sale and purchase agreement relating to this product by the Trade
Practices Act 1974 (as amended) or any other law (whether a law of Australia or any other country) other than a condition implied by Section
69 of the said Act is limited at our option to:
the replacement of the product; or
the supply of an equivalent product; or
the repair of the product.
If you do not accept the above conditions, return this product (in the original packaging) with proof of purchase for a full refund.
!