Krix Stratospherix User manual

Installation Guide
Stratospherix

Care should be taken to ensure that
the ceiling material is strong enough to
support the product weight. Structural
materials such as plaster board, cement
sheet and wood are generally suitable.
Non-structural ceiling materials, such as
fibre mat suspended ceiling tiles are NOT
suitable without additional reinforcement.
connecting
To ensure optimum performance it is
important that your speaker system is
connected properly:
Turn off all electronic equipment and
disconnect from the power point.
Follow the connection instructions•
supplied with your amplifier, CD/DVD, hard
disk recorder, video player etc.
• Install speaker cable in wall or ceiling
cavity, or run cable along wall surface.
Allow approximately 300mm of excess
cable to facilitate loudspeaker installation.
• Follow the connection instructions
supplied with your amplifier to connect
the speaker cables to amplifier. Take care
to assign the same cable colour or trace to
the positive (+) connector on the amplifier
as the positive (+) connector on the
speaker.
• Prepare speaker cables for connecting to
speakers by neatly stripping cable ends.
Care should be taken to eliminate loose
strands of wire that may present a short
circuit hazard.
installation
Once the correct speaker placement has•
been determined, use the cardboard insert
marked ‘template’ (from the internal
packing) to trace the required cut-out onto
the ceiling/wall. (figure 2)
Drill a hole inside the marked cut-out.•
Using a fine plasterboard saw cut around
the inside of the marked cut-out.
(figure 3)
Remove the circular offcut and insert the•
speaker to check the hole is the correct
size. Enlarge the cut-out if required.
installation
To install the speaker, first remove the•
grille. To remove the speaker grille use
the mounting clamps located around the
edge of the enclosure. Swing the mounting
clamps out so that they are 90 degrees to
the enclosure, and gently push upwards
evenly on the clamps until the grille lifts.
Carefully lift out the grille without bending.
(figure 4)
Pull the stripped speaker cable through the•
ceiling/wall opening. Push and hold down
the positive (+) red binding post on the
speaker and insert the positive (+) wire
through the hole in the post. Take care to
assign the same cable colour or trace to
the positive (+) connector on the amplifier
as the positive (+) connector on the
speaker. Repeat connection process with
the negative (-) black binding post and
the negative (-) wire. (figure 5)
Ensure all mounting clamps are swung•
back against the speaker enclosure
(figure 5), so that the speaker can be
easily inserted into the ceiling cut-out.
Once the speaker has been located in
the ceiling/wall, use a Phillips head
screwdriver to tighten all mounting
screws. Be careful not to over tighten
screws, as this may strip the clamp,
or crush the plaster board surface. As
the screws are tightened, the mounting
clamps will automatically swing out over
the plaster board and clamp the speaker in
place. (figure 6)
If painting the grille and speaker frame is•
not required, gently fit the metal grille to
the front of the speaker housing.
(figure 7)
If the grille and speaker frame require•
painting, ensure the black front baffle
is masked off to protect the speaker
drivers. When painting the metal grille it is
recommended to use a small foam roller
and it may necessary to thin down the
paint to avoiding blocking the holes in the
grille. After all paint is dry, fit the grille to
the front of the speaker housing.
introduction
The Stratospherix is a high quality in-ceiling
loudspeaker featuring a semi enclosed back-
box. It employs a large 200mm (8”) bass
driver with concentric professional grade
compression tweeter, for high power handling
and sensitivity. The dual concentric driver
configuration guarantees uniform sound
coverage in all directions. The bass driver
features a weather-proof polypropylene cone,
whilst the compression tweeter is protected
by an acoustically transparent dust cap. To
ensure reliable performance both indoors
and outdoors the grille is made of corrosion
resistant aluminium and all other hardware is
stainless steel.
applications
The weather-proof design of the
Stratospherix, combined with high power
handling, sensitivity and extended bass
performance, make it ideally suited to outdoor
in-ceiling applications. For example, it can be
used in undercover alfresco dinning areas,
courtyards or near swimming pools. The
Stratospherix may also be used for indoor
applications requiring high volume levels, for
example larger concealed home cinemas.
before you begin
Please read the disclaimer on the back
of this manual.
After discussion with your local Krix•
distributor, or installation consultant,
determine the best location for your
loudspeakers. Check for any obstructions,
such as electrical wiring, plumbing, stud
work or air conditioning ducts before
commencing the installation. (figure 1)
Also check that there is enough ceiling
depth to accommodate the speaker
enclosure.
figure 1
2
!
!
Congratulations on choosing Krix
Your Krix speakers are designed to reproduce the highest quality sound. To get the best
performance from your speakers please read these installation instructions thoroughly as there
are many factors that influence the performance of your speakers. If you have any difficulties
please speak with one of our friendly authorised Krix dealers.
!

!
!

installation
3
figure 6
figure 5
figure 3figure 2
figure 4 .
figure 7

krix.com
Krix Loudspeakers Pty Ltd
14 Chapman Road
Hackham SA 5163
Australia
T 61 8 8384 3433
F 61 8 8384 3419
[email protected] Rev #10001
disclaimer
Cutting or drilling into anything can be dangerous. You should make sure you know what is behind or inside the surface that you are cutting
into before you start to cut. For example, you might strike an electrical cable.
If you do not feel entirely confident about installing this product, contact a professional installer.
disclaimer
To the extent permissible by law:
All warranties, conditions, representations, promises and statements relating howsoever to this product whether express or implied and
whether in contract or tort are excluded to the extent permitted by law; and
Our liability to you under a condition or warranty (if any) implied into this sale and purchase agreement relating to this product by the Trade
Practices Act 1974 (as amended) or any other law (whether a law of Australia or any other country) other than a condition implied by Section
69 of the said Act is limited at our option to:
the replacement of the product; or
the supply of an equivalent product; or
the repair of the product.
If you do not accept the above conditions, return this product (in the original packaging) with proof of purchase for a full refund.
!