Kross KRC 300 Series User manual

KRC 300 Series
KRC 307, KRC 309, KRC 311
Please check that all the following items have been included with the cycle computer before starting.
KRC 300 Series cycle computer Rubber
Nylon ties x 4 Pcs Speed Magnet
Bracket Sensor
Stabling Pad
How to mount the bracket
Bracket
Nylon Ties
(2)(1)
Rubber
Bracket
Cycle Computer
Rubber
Bracket
Cycle Computer
Use the rubber to tighten the bracket to the handlebar or stem with the nylon ties.
How to mount the cycle computer
(3)
Place the cycle computer on the bracket and secure it in clockwise.
Nylon Tie
(4)
(5) Stabling Pad
How to mount the Speed Sensor
Check the position of the front fork to find the suitable point to attach
the speed sensor.Use the rubber to avoid slipping. The speed sensor should
be mount with nylon ties in the inner side of the chosen front fork.
(6)
Magnet
Screw
How to mount the Magnet
(7 )
Sensor
1~5mm
Magnet
Secure the Speed Magnet on the spoke of the front wheel with screw.
Make sure the magnet side faces the speed sensor zone.
The maximum distance between the speed sensor and the magnet on the spoke
is 5 mm. Once above items in the right position, the user may go for a ride.
Note:
Please make sure everything has been setup correctly before riding the bicycle.
Wheel Circumference
To get the accurate result, the wheel size should be
correct. Mark the symbol on the tire and ride one circle.
Then measure the length between two points to get the
circumference.Or the user can also get wheel
circumference by the following equation:
Circumference (mm) = 2 x 3.14 x R (inch) x 2.54
(1 inch = 2.54 cm) R=Radius in centimeter
The user can refer the "wheel size chart"for the
wheel size.
The cycle computer main display and Key function
SET KEY
MODE KEY
Current Speed Speed Scale Symbol
PM Indicator
(Post Meridiem)
Sub Display
Bike 1 or Bike 2
(Option in KRC 300)
Current Speed
compare to Average
Speed.
Above/Below
KM
/
H
Mode Change
Press Mode key shortly to change mode.
CLK MODE (Clock Mode)
12/24H and Time switch
TM MODE ( TTrip ime Mode)
AVS MODE (Average Speed Mode)
MXS MODE (Max Speed Mode)
DST MODE (Distance Mode)
ODO
ODO
1 MODE (Odometer 1 Mode)
2 MODE (Odometer 2 Mode)
(option KRC 311 )
(option KRC 311 )
ODO MODE (Total ODO Mode)
KCAL MODE ( Calorie Mode)
(Except KRC 307)
(Except KRC 307)
KM
/
H
S > 3 sec
M
M
CLK MODE (Clock Mode)
How to set the Time Press and
hold "SET" key for 3 seconds
to go setting clock. Press
"SET" key once to adjust
12/24 hours.
Press "MODE" key to adjust
time (hour, minute and
second).
Hold "MODE" key for 3 seconds to go back to Clock Mode
once the setting is finished.
TM MODE (Trip Time Mode)
Trip Timer would operate automatically when the bike is in motion
How to reset all data (KCAL, TM, AVS, MXS, DST)
Note:
Press and hold "SET" key for 3 seconds,all exercises results in displayer will return
to zero, except odometer.
KM
/
H
S
S>3sec
KM
/
H KM
/
H
AVS MODE (Average Speed Mode) MXS MODE (Maximum Speed Mode)
KM
/
HKM
/
H
Note:
If the time or distance is over the max value
(29 hr: 59 min: 59 sec or Distance: 999.99km)
, It will not be able to measure correct average
speed by showing "Err" on the display.
Once the time & distance value has been reset, the
average speed will show normally.
DST MODE (Distance Mode)
KM
/
H
The average speed from
the beginning onwards.
The maximum speed from
the beginning onwards
ODO 1 MODE ODO 2 MODE
KM
/
H
KM
/
H
The odo accumulated
from bike 1.
The odo accumulated
from bike 2.
ODO (Total Odometer Mode)
KM
/
H
KM
/
H
KM
/
HKM
/
H KM
/
H
KM
/
H KM
/
H
S > 3 sec
MM
M
S
Total odometer accumulated from the beginning onwards.
Note:Odometer mode will return to zero after changing new battery.
How to change speed scale, bike1&bike2, wheel settings and ODO1
(option KRC 311)
Under ODO Mode, press "SET" key for 3 seconds to go to setting.
M
Press "SET" key again to select Km/H or Mile/H,
press "MODE" key to go to Bike1&Bike2 Setting,
then press "SET" key to select Bike1 or Bike2.
Press "MODE" key to go to Wheel Settings.
Input the correct wheel size by pressing "SET" key
the range of wheel size from 100mm to 2,999mm.
For users to input previous accumulated ODO after new battery,
press "MODE" key to go to ODO1 Setting,
Input the previous ODO by pressing "SET" key,
the range of ODO1 is from 1 to 99999.
Hold "MODE" key for 3 seconds to go back to ODO Mode.
Press "SET" key to select preferable Kg or Lb weight scale.
Then, press "MODE" key to go to weight input.
KCAL MODE (Calorie Mode)
Press "SET" key for 3 seconds to go to gender setting.
Press "SET" key again to select MALE or FEMALE,
then press "MODE" key to go to Kg or Lb Setting.
KCAL
KM
/
H
S M M>3sec
It displays the accumulated calories consumed from the beginning of the trip
onwards.
Note:
This accumulated calories display will return to 0 once it has been clear under
the TM MODE.
How to input gender, weight scale and weight.
Press "SET" key to input the actual weight in Kg or Lb.
Press and hold "MODE" key for 3 seconds to go back to KCAL Mode.
MAINTENANCE
KRC 300
KRC 300
R
R
LIMITED WARRANTY
This product is for one year limited warranty commencing on the date of purchase.
The product will be free from defects in material and workmanship for one year
from the date of purchase.
Warranty does not cover the batteries, damages due to misuse,
abuse or accidents, cracked or broken cases, negligence of precautions,
improper maintenance or commercial use.
Warranty is void if the repairs are done by non authorized service technician.
The warranties contained herein are expressly in lieu of any other warranties including
implied warranty of merchantability and/ or fitness for purpose. In no event shall
manufacturer be liable for any damages, direct or incidental, consequential or special,
arising out of or related to the use of this manual or the products described herein.
During this warranty period (one year) the product will eith er be repaired
or replaced without charge.
KM
/
H
The trip distance accumulated from the beginning onwards.
KRC 300 Series Cycle Computer