Krups XP1000 User manual

www.k ups.com
XP1000
ENGLISHFRANÇAIS
ESPAÑOL
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mi e en page 1 08/06/12 10:42 Page2

2
When using electrical appliances, basic safety
precautions should always be followed to reduce the
risk of fire, electric shock, and/or injury to persons
including the following:
1. Read all instructions prior to first use.
2. Do not touch hot surfaces. Always use handles or
knobs.
3. To protect against fire, electric shock and injury to
persons, do not immerse cord, plugs or machine in
water or other liquid.
4. Not intented for use by children.
5. Close supervision is necessary when any machine is
used near children. Keep machine out of reach of
children.
6. This appliance is not designed to be used by children
or people without knowledge or experience with the
machine.
7. Children must be supervised to ensure that they do
not play with the appliance.
8. Burns can occur from touching the hot plate, hot water
or steam. Exercise caution.
9. Exercise caution when using the steam nozzle as
steam can cause scalding.
IMPORTANT
SAFEGUARDS
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en age 1 18/06/12 09:45 Page2

ENGLISH
3
10. Unplug machine from outlet when not in use and when
cleaning. Allow to cool before putting on or taking off
parts, before cleaning the machine, and before storing.
11. All machines are subject to stringent quality control.
Practical tests using machines taken at random are
conducted and this may explain any slight marks or
coffee residue prior to use.
12. Do not operate any machine with a damaged cord or
plug or after the machine malfunctions, or has been
damaged in any manner. Return machine to the
nearest Krups Service Center for examination, repair
or adjustment or your respective countries Consumer
Service Department.
13. To reduce the risk of injury do not drape cord over the
counter top or table top where it can be pulled on by
children or tripped over accidentally.
14. Do not let cord hang over edge of table or counter, or
touch hot surfaces.
15. The use of accessory attachments not recommended
by Krups may result in fire, electric shock or injury to
persons.
16. Do not use outdoors.
17. Do not place on or near a hot gas or electric burner, or
in a heated oven.
18. To disconnect the machine, turn the control to “off”
then remove plug from wall outlet. Do not yank cord,
instead grasp plug and pull to disconnect.
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en age 1 18/06/12 09:45 Page3

4
19. Do not use the machine for anything other than its
intended use.
20. Do not pour liquids other than water and descaling
solutions specified in this manual into the water tank.
21. Protect the machine against humidity and freezing.
22. Scalding may occur if the lid is removed during the
brewing cycles.
23. This machine is for household use only.
SAVE THESE
INSTRUCTIONS
CAUTION
This machine is intended for household use only. Any
servicing other than cleaning and user maintenance
should be performed by the nearest authorized Krups
Service Center.
Visit our website at www.krupsusa.com in the USA or
www.krups.ca in Canada or contact your respective
country's Consumer Service department for the service
center nearest to you.
To reduce the risk of fire or electric shock, do not attempt
to disassemble the machine. Repair should be done by an
authorized Krups Service Center only.
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en age 1 18/06/12 09:45 Page4

5
ENGLISH
A short power-supply cord is to be provided to reduce risks
resulting from becoming entangled in or tripping over a longer cord.
A. We do not recommend using an extension cord with this
device.
B. If an extension cord is absolutely necessary,
1) the marked electrical rating of the extension cord
should be at least as great as the electrical rating of
the machine,
2) the longer cord should be arranged so that it will not
drape over the counter top or table top where it can
be pulled on by children or tripped over.
C. This machine has a polarized plug (one blade is wider
than the other). To reduce the risk of electric shock, this
plug is intended to fit into a polarized outlet only one way.
If the plug does not fit fully into the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician.
Do not attempt to modify the plug in any way.
In the interest of improving products, Krups reserves the right to
change specifications without prior notice.
SHORT CORD INSTRUCTIONS
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en age 1 18/06/12 09:45 Page5

i
b
b3
b1
b2
bc
g
h
f
e
d
c1
c2
a
c
6
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en age 1 18/06/12 09:45 Page6

1 2
3 4
5 6
7
ENGLISH
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en age 1 18/06/12 09:45 Page7

7 8
9 10
11
8
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en age 1 18/06/12 09:45 Page8

9
ENGLISH
Espresso is a richer and more aromatic brew than regular coffee.
It is typically enjoyed in smaller quantities because of its richness,
and for that reason, espresso is usually served in small (1.5 - 2
oz) cups.
Your appliance when properly used will produce espresso that is
deep in flavor and dark in color. ust follow the instructions and
use fresh roasted coffee that has been pre-ground to an espresso
grind.
Preparing an espresso or cappuccino is different from brewing
regular drip coffee. One main difference is that the water will
come to a boil and will then be forced through the ground coffee.
This means that an espresso machine works under pressure and
needs special attention.
DESCRIPTION
aON/OFF Pilot light
bSelector knob
b1 Off position
b2 Espresso-coffee making
position
b3 Hot steam position
cFilter-holder
c1 Removable filter for 1
to 4 cups
c2 Filter locker
dMeasuring spoon
eCarafe
fRemovable drip tray grid
gCappuccino accessory
hSteam nozzle
iBoiler cap for water tank
AUTHENTIC ESPRESSO
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en age 1 18/06/12 09:45 Page9

10
CAUTION – PRESSURE
Never open boiler cap (i) or remove filter holder (c) while your
appliance is turned “on” or while there is still pressure in the
boiler container.
To check for pressure:
Turn the selector knob (b) to the “Off” position. Fig. 1.
Turn the selector knob to the steam position (b3) Fig. 10. If steam
comes out of the nozzle, then the boiler chamber is still under
pressure. Close steam knob and proceed with instructions listed
below.
Take a pitcher filled with cold water and hold it underneath the
steam nozzle with nozzle inserted into the pitcher. Then turn the
selector knob to the steam position (b3). Leave steam release
knob open until no more steam comes out of nozzle. When
finished turn the selector knob (b) to the “Off” position.
Now you can remove the boiler cap and the filter holder.
CAUTION – HOT
Do not touch boiler cap (i) during operation. Before removing
boiler cap turn off machine, let it cool down for at least 2 or
3 minutes. Relieve pressure. (See CAUTION-PRESSURE).
Important! Before using your machine for the first time, or after
not having used it for a considerable amont of time, rinse the
appliance as indicated below. Check that the appliance is
unplugged.
Check that the appliance is unplugged.
Unscrew the boiler cap. Fig. 2.
Pour 8 oz (240 ml) of cold water into the water tank. Do not pour
warm or hot water into the water tank. Fig. 3.
Screw the boiler cap on tightly. Fig. 4.
Fit the filter (without any coffee) into the filter-holder and rotate
filter inside filter-holder to secure it. Fig. 5.
BEFORE FIRST USE
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en age 1 18/06/12 09:45 Page10

11
Insert the filter holder in the appliance. Turn it firmly from left to
right to put it into the “locked” position. Fig. 6.
Place the carafe or a cup under the filter holder. Plug in the
appliance. Fig. 7.
Turn the selector knob to the “Espresso” position (b2). Fig. 8.
The ON/OFF pilot light will light up.
After a few minutes, the water will boil and hot water will start to
drip. When the container/cup is full, turn the selector knob to the
“Off” position (b1).
Place a cup under the steam nozzle and turn the selector knob
to the steam setting (b3). When there is no more steam, turn to
the “Off” position (b1).
Never remove filter holder or open boiler cap without having
released remaining pressure in appliance. (See CAUTION-
PRESSURE).
Important! Check that the appliance is unplugged and that
there is no pressure. (See CAUTION-PRESSURE).
Unscrew the boiler cap Fig. 2. Measure out the right amount of
water for your needs and pour it into the water tank. For instance:
an espresso-sized cup (small cup for strong espresso) = 1 to 2
oz (25 to 50 ml). A standard-sized cup (for milder espresso) = 3
to 4 oz (75 to 100 ml). Up to 4 espressos or 2 standard cups can
be made at one time, without adding additional water to the tank.
Pour the water into the tank. Fig. 3.
Screw the boiler cap on tightly. Fig. 4.
Plug in the appliance.
Fit the filter into the filter-holder and rotate filter inside filter-holder
to secure it. Fig. 5.
Put the ground coffee into the filter holder using the measuring
spoon. 1 full measuring spoon is the amount needed for 1
MA ING ESPRESSO
ENGLISH
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en age 1 18/06/12 09:45 Page11

12
espresso. Using a tamper or the back of the measuring spoon
tamp down the coffee.
Remove any excess coffee on the edge of the filter-holder.
ATTENTION! Do not over fill or pack coffee too tightly.
Fit the filter-holder into the appliance turning it from left to right
and locking it firmly into place. Fig. 6.
Place a cup or the carafe under the filter-holder. Fig. 7.
Turn the selector knob to “espresso” (b2).Fig. 8.
The ON/OFF pilot light will light up. After 3 to 4 minutes, the
espresso will start to drip. Wait until the espresso has stopped
dripping before removing the cup or carafe and then turn the
selector knob to the “Off” position (b1).Fig. 9.
ATTENTION! We advise you to not switch off the appliance
before the cycle is completely finished. At the end of the
cycle, steam will dry out the coffee grounds thus producing a
puck that is drier and easier to remove. Never remove filter
holder or open the water tank without having released
remaining pressure in appliance. (See CAUTION-PRESSURE).
Once you have removed the pressure from the machine the
filter holder can be removed. To throw away the coffee
grounds, turn over the filter holder and shake it to make the
coffee grounds fall out.
Follow the instructions for “Making Espresso” but add 2 oz (50
ml) of water to the volumes indicated.
An authentic cappuccino is made using 1/3 espresso, 1/3 hot
steamed milk and 1/3 frothed milk. We recommend frothing the
milk before making the coffee.
Pour 4 to 6 oz (100 to 150 ml) of fresh, cold milk into a small
pitcher. Do not use a pitcher cleaned with hot water or one that is
still warm.
MA ING CAPPUCCINOS
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en age 1 18/06/12 09:45 Page12

13
The milk will froth better in a cold pitcher. The pitcher should fit
underneath the cappuccino nozzle. We recommend using 1 or
2% milk for a stiff, dense froth. Use whole milk if you prefer a
creamy froth.
Turn the knob to the “Steam” position (b3).Fig. 10.
When the steam starts coming out of the nozzle, immerse the
nozzle in the pitcher of milk and make circular movements going
up and down to froth the milk. It is important not to have the
nozzle touch the bottom of your pitcher. Fig. 11.
Once the milk is frothed, put a cup underneath the filter holder.
Turn the knob to the “Espresso” position (b2).Fig. 8.
Once the espresso has finished dripping, spoon the frothy milk
over the espresso to finish the cappuccino. Never remove filter
holder or open boiler cap without having released remaining
pressure. (See CAUTION-PRESSURE).
ATTENTION! Clogged Steam nozzle:
Milk residue will build up in the tip of the steam nozzle after
frothing milk. To avoid clogging, remove the plastic housing of
the cappuccino nozzle once the appliance has cooled, for easy
cleaning. Then follow “cleaning the steam nozzle” as described
in the section “Cleaning the Cappuccino Nozzle”.
Don’t forget to replace the tip of the nozzle and screw it on tightly.
Follow the instructions for “Making Cappuccinos” with the
following proportions: 2/3 frothy milk, 1/3 espresso, and if desired
you may spoon some milk foam on top.
Steam is used to froth milk and also to reheat water (tea, hot
drinks).
MA ING CAFFE LATTES
STEAMING WITHOUT MA ING ESPRESSO
ENGLISH
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en age 1 18/06/12 09:45 Page13

14
Check that the appliance is unplugged and that there is no
contained pressure. (See CAUTION-PRESSURE).
Measure out a small amount of water and pour into tank. For
example: 2 oz (50 ml) of water to heat 4 oz (100 ml) of liquid.
Important: for maximum efficiency, avoid putting more than
4 oz (100 ml) of water into the tank.
Tightly screw on the boiler cap. Fig. 4.
Plug in the appliance.
Immerse the steam nozzle in the liquid to be heated.
Turn the knob to “steam” (b3).Fig. 10.
The ON/OFF pilot light will light up.
Steam is produced after 2 to 3 minutes of preheating.
Once the liquid is hot, turn selector knob back to “Off” (b1) and
unplug the appliance.
If you do not need all the water for steaming, proceed as follows:
Turn off the machine.
Release the remaining steam pressure into another container.
Before turning the knob again, turn the knob to “steam” (b3) to
remove any steam, take care to put a cup underneath the steam
nozzle.
CAUTION! Do not turn the selector knob back to "Off" (b1)
before all steam is released! (See CAUTION - PRESSURE).
ATTENTION! The plastic housing of the cappuccino nozzle
(g) has 2 fine holes at the top which draw air into the milk.
If those holes get clogged, the milk will not be frothed
properly. Therefore, do not dip the cappuccino nozzle in milk
or froth up to those holes.
ATTENTION! Immediately after use, wash the steam nozzle
with a damp sponge.
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en age 1 18/06/12 09:45 Page14

15
Unplug the appliance and let it cool down completely before you
clean it.
Occasionally wipe the outside of the appliance with a damp
cloth. Regularly wash and dry the drip tray and its grid.
Do not use alcohol-based or abrasive cleaning products or
solvents.
Regularly clean the grid through which the hot water passes with
a damp sponge.
Important: Never use soap or other cleaning agents as it will
impact the taste of your beverages.
Clean the steam nozzle each time after you have immersed it in
the milk, otherwise the inside of the nozzle can become clogged
and the milk deposits on the outside will harden and become
difficult to remove.
If clogging does occur, remove the plastic housing of the
cappuccino nozzle (g) once the appliance has cooled and then
unscrew the tip of the steam nozzle.
Remove all milk particles by using a clean sewing needle and
rinse under the faucet. Replace nozzle tip making sure to screw
it on tightly. Wipe off the outside of the nozzle with a wet cloth.
The plastic housing of the cappuccino nozzle should be rinsed
in warm water. If the small suction openings are clogged up, they
can be opened with a small needle.
CAUTION! Do not try to open or disassemble the main body
of the machine.
CLEANING AND SERVICING
CLEANING THE CAPPUCCINO NOZZLE
ENGLISH
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en age 1 18/06/12 09:45 Page15

16
The warranty does not cover a faulty or broken espresso
machine due to not being descaled.
Due to the acidity of the cleaning solution, we recommend
protecting your worktop and sink during the descaling process,
especially if it is made of marble or stone. Isolate your appliance
with an old towel, tablecloth or tray.
The espresso machine must be decalcified regularly. The
frequency depends on the hardness of your water and how often
you use the espresso machine.
Before descaling, the brewing sieve on the brewing head must
first be screwed off.
1. Remove all lime and coffee residues from the brewing sieve
and the brewing head.
2. Remove the plastic housing of the cappuccino nozzle (g).
As a descaling agent we recommend the use of Krups descaling
solution F054 available at authorized Krups retailers and Service
Centres or by contacting your respective countries Customer
Service Department.
3. Dissolve a packet of KRUPS descaling solution in 10 oz/300
ml of lukewarm water and pour into the boiler container and
screw back the cap. Put a container under the brewing head
and another under the steam nozzle.
(Note: Do not secure the filter holder (c) during decalcification).
4. Open the steam valve and turn on the appliance. Allow the
descaling solution to run out of the espresso outlet and the
steam nozzle.
5. After each brewing cycle, switch off the appliance and allow
the appliance to cool down.
6. Repeat this operation once more.
Following this, allow 2 containers of clear water to run through
the system. Switch off the appliance. Allow the appliance to cool
down. Insert the brewing sieve into the brewing head again and
push the plastic housing of the cappuccino nozzle onto the
steam nozzle.
DECALCIFYING THE ESPRESSO SIDE
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en age 1 18/06/12 09:45 Page16

17
TROUBLESHOOTING
Problems Probable Causes Solutions
Espresso
The coffee drips
too slowly. The coffee is ground
too fine.
Filter blocked.
Water passage grid is
clogged.
Presence of scale.
Use more coarsely
ground coffee.
Clean it with a brush.
Clean the appliance
when cold.
De-Scale the
appliance.
The coffee drips
too slowly. Dirty filter-holder or
dirty filter.
The coffee is ground
too fine.
Clean them with hot
water.
Use more coarsely
ground coffee.
The coffee
doesn’t drip. The knob is in the “Steam” position
(b3).
Turn the knob to the
“Espresso” position
(b2).
The espresso
leaks onto the
filter holder sides.
Filter holder is
clogged up.
The filter holder is not
properly positioned.
Remove any excess
ground coffee.
Put it back into place
and lock it into
position.
Bad taste. Insufficient rinsing. Follow the rinsing
instructions.
Steam
Water runs out of
the filter holder. The knob is in the
“Espresso”
position (b2).
Turn the knob to the
“Steam” position (b3).
Little or no steam
in the “steam”
position.
The knob opened too
early. Close the “Steam” knob for 2
minutes.
ENGLISH
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en age 1 18/06/12 09:45 Page17

18
: www.krups.com
With a strong commitment to the environment, most of rups
products are repairable during and after the warranty period.
Before returning any defective products to the point of
purchase, please call rups consumer service directly at the
phone number below for repair options. Your help to sustain
the environment is appreciated!
The Warranty
This product is guaranteed by Krups for a period of 2 years against
any manufacturing defect in materials or workmanship, starting
from the initial date of purchase.
The manufacturer's warranty by Krups is an extra benefit which
does not affect consumer's Statutory Rights.
The Krups warranty covers all costs related to restoring the proven
defective product so that it conforms to its original specifications,
through the repair or replacement of any defective part and the ne-
cessary labor. At Krups’s choice, a replacement product may be
provided instead of repairing a defective product. Krups’s sole obli-
gation and your exclusive resolution under this warranty are limited
to such repair or replacement.
Problems Probable Causes Solutions
The steam nozzle
doesn’t froth the
milk.
Blocked steam
nozzle.
Whole milk used.
Milk not fresh or cold
enough.
Container doesn’t
have the right shape.
Rinse out the steam
nozzle.
Use 1 or 2% milk.
Always use very fresh,
cold milk.
Use a small diameter
container (small jug).
LIMITED WARRANTY
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en age 1 18/06/12 09:45 Page18

19
Conditions & Exclusions
The Krups warranty only applies within USA, Canada & Mexico,
and is valid only on presentation of a proof of purchase. The pro-
duct can be taken directly in person to an authorized
service centre or must be adequately packaged and returned, by
recorded delivery (or equivalent method of postage), to a Krups au-
thorized service centre. Full address details for each country’s au-
thorized service centre are listed on the Krups website
(www.krups.com) or by calling the appropriate telephone number
listed below to request the appropriate postal address.
Krups shall not be obliged to repair or replace any product which
is not accompanied by a valid proof of purchase.
This warranty will not cover any damage which could occur as a
result of misuse, negligence, failure to follow Krups instructions,
use on current or voltage other than as stamped on the product,
or a modification or unauthorized repair of the product. It also does
not cover normal tear and wear, maintenance or replacement of
consumable parts, and the following:
- using the wrong type of water
- scaling (any de-scaling must be carried out according to the
instructions for use);
- ingress of water, dust or insects into the product;
- mechanical damages, overloading
- damages or bad results due to wrong voltage or frequency
- accidents including fire, flood, lightning, etc
- professional or commercial use
- damage to any glass or porcelain ware in the product
This warranty does not apply to any product that has been tampe-
red with, or to damages incurred through improper use and care,
faulty packaging by the owner or mishandling by any carrier.
The Krups manufacturer's warranty applies only for products pur-
chased and used in USA, Canada & Mexico. Where a product pur-
chased in one country and then used in another one:
a) The Krups guarantee duration is the one in the country of
usage of the product, even if the product was purchased in
another listed country with different guarantee duration.
ENGLISH
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en age 1 18/06/12 09:45 Page19

20
b) The Krups guarantee does not apply in case of non confor-
mity of the purchased product with the local standards, such
as voltage, frequency, power plugs, or other local technical
specifications
c) The repair process for products purchased outside the coun-
try of use may require a longer time if the product is not locally
sold by Krups
d) In cases where the product is not repairable in the new coun-
try, the Krups guarantee is limited to a replacement by a si-
milar product or an alternative product at similar cost, where
possible.
Consumer Statutory Rights
This Krups manufacturer's warranty does not affect the statutory
rights a consumer may have or those rights that cannot be excluded
or limited, nor rights against the retailer from which the consumer
purchased the product. This warranty gives a consumer specific
legal rights, and the consumer may also have other legal rights
which vary from State to State or Country to Country or Province to
Province. The consumer may assert any such rights at his sole dis-
cretion.
Additional information
Accessories, Consumables and end-user replaceable parts can be
purchased, if locally available, as described in Krups internet site.
: www.krups.com
CANADA
GROUPE SEB
CANADA
345 Passmore
Avenue
Toronto, ON
M1V 3N8
MEXICO
Groupe SEB
MEXICO
S.A. de C.V.
Goldsmith 38 Desp.
401 Col. Polanco
Delegacion Miguel
Hildalgo
11 560 Mexico D.F.
MEXICO
U.S.A.
GROUPE SEB
USA
2121 Eden
Road
Millville, N
08332
1-800-418-3325 01800 1128325 800-526-5377
KR_COFFEEMAKERS_ESPRESSO-XP1000_8080011304_Mise en age 1 18/06/12 09:45 Page20