KS RnD KS-RPM Triple User manual

User Manual
KS RnD CO., LTD.

KS-RPM Triple User Manual
2
User Manual
V0.55
Table of contents
User Precaution ………………………… 3
Composition Item ………………………… 4
Option ………………………… 4
Technical Specifications ………………………… 5
Material ………………………… 5
Preparation before Use ………………………… 6
Product Name ………………………… 6
How to Connect Devices ………………………… 7
How to Use ………………………… 8

KS RnD CO., LTD.
3
User Precautions
Please use this product after you have read the manual carefully
to use the device more safely and efficiently.
<General Safety Compliance>
1. Don’t use this product except for those who know how to use.
2. Don’t execute text of manual before measurement.
3. Do not disassemble the device.
<Dangerous>
1. This product’s 12V adapter is dedicated to AC220V. Please check the power before use.
2. Avoid content with rotor near the engine during measuring engine speed.
3. When you measure engine speed, be cautions for burn.
4. For your safety, hold the hand brake and put the bridging in front and in back of the tire.
※This document uses Naver’s Nanum fonts.

KS-RPM Triple User Manual
4
Composition Item
Composition
Contents
Product
Machine
Sensor 1
Battery clamp of measuring RPM (3 m)
Sensor 2
Cigar lighter jack of measuring RPM (1 m)
Sensor 3
Vibration sensor of measuring RPM (2 m)
Sensor 4
Sound sensor of measuring RPM (2 m)
Power
USB travel charger
Etc.
User manual
Option
Option
Contents
Wireless communication
Bluetooth module

KS RnD CO., LTD.
5
Technical Specifications
Details
Contents
RPM
Analysis Range
10 ~ 5,000 rpm
Resolving Power
10 rpm
Oil
Temp.
Analysis Range
0 ~ 200 ℃
Resolving Power
0.1 ℃
Use Temperature
-10 ~ 45 ℃
Use Humidity
30 ~ 90 %
Weight
300 g
Dimensions
90(W) * 152(H) * 32(D) mm
Power Supply
12V DC Adapter
Power Consumption
200 mA
Communication
RS232
Material
Name
Material
The Product Body
Aluminum
Sensor Cable
Urethane
Sensor Measurement
Aluminum, Steel

KS-RPM Triple User Manual
6
Preparation before use
How to charge the battery
As shown in the figure below, charger is connected to the terminal as in the .
Charge time & use time
Charge time
About 4 times
Use time
About 10 times
Product Name

KS RnD CO., LTD.
7
How to Connect Devices
▪Use battery clamp
1) Connect the battery clamp (8 pin connecter) to of device.
2) Connection
(+) terminal -> Red clamp
(-) terminal -> Black clamp
※Please connect the terminal correctly, even though miss match of the terminals
doesn’t harm of device.
The more cars make noises the better it is measured. If possible, turn on the
headlight before measurement so that the battery gets some loads.
3) Turn on the power .
▪Using vibration sensor
1) Connect the vibration sensor (8 pin connecter) to of the device.
2) Attach sensor on flat surface around the engine and turn on the power .
The more engine vibrates, the better it is measured.
▪Using sound sensor
1) Connect the sound sensor (8 pin connecter) to of device.
2) Attach sensor on flat surface around the engine and the power is turned on.
The little engine vibrates, the better it is measured.

KS-RPM Triple User Manual
8
▪Using oil temperature sensor
1) Connect the oil temperature sensor (8 pin connecter) to of device.
2) Turn the power on , and input your sensor to place that measure the car’s
engine oil.
※Watch out burn since engine oil is hot.
How to use function
▪Screen in the beginning
1) Version is displayed when you turn on the power.
2) After a while, by moving the connected sensor, the display marks a measured value.
(In case of no connecting the display will mark [ - - - - ].)
▪How to select cylinder
1) Using key, enter the cylinder set-up mode.
Key name
Explanation
Enter set-up mode
After set-up mode, operation up, down
Potion wanted mode, press SET.

KS RnD CO., LTD.
9
2) Using key, select the number of cylinder.
The order of cylinder number movements 1→2→3→4→5→6→8→10→12→1.
3) Using key, set-up cylinder number.
▪How to set-up manual factor(only battery clamp)
When you want to measure the value more correctly.
1) If you push the key, “CONTINUITY” message will disappear and factor mode
will be ready.
2) Push the key when the current value is lower than RPM gage.
Push the key when the current value is higher than RPM gage.
3) If you push key, “CONTINUITY” message will be marked.

KS RnD CO., LTD.
Techno-park 201-906-1, 388, Songnae-daero, Wonmi-gu,
Bucheon-si, Gyeonggi-do 420-733 Korea
Tel : [phone] Fax : [phone]
www.ksrnd.com