KT&C HDX131M User manual

HD CCTV
Digital Video Camera
OPERATION MANUAL
Thank you for choosing our high quality camera.
Before attempting to connect or operate, please read and follow
these instructions.
M090-HDX131ME-001

CONTENTS
1. CAUTIONS
2. FEATURES
3. COMPONENTS
4. NAME AND FUNCTION
5. INSTALLATION
6. DIMENSIONS
7. SPECIFICATION
8. DIGITAL INPUT/OUTPUT
9. OSD MANUAL
3

4
1. CAUTIONS
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.”
WARNING
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Caution
Any changes or modications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
1. A regulated DC12V 1A power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be out of subject.
2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal componets.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which may
cause smear on the picture and possible damage to the CCD.
5. Do not remove the serial sticker for the warranty service.
6. Do not expose the camera to rain or other types of liquid.
7. The apparatus must be connected to a mains socket-outlet with a protective earthing
connection.

1. CAUTIONS
5
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicate that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes purchased this
product, or their local government ofce, for details of where and how they can
take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
Household users should contact either the retailer where they for disposal.

2. FEATURES
•High Resolution
1/3” SONY Color CMOS Image Sensor
1280x720 30fps
• Support various digital video output
720p 30, 720p 60
720p 25, 720p 50
• Video Output
HD-SDI (BNC)
TV Out (BNC), NTSC /PAL selectable
• Horizontal Resolution : more than 600 TV Line
• S/N Ratio : Max 50dB
• Support OSD menu
• Lens Control
Fixed,
DC Iris(Video Iris) (factory selectable)
• Support True Day/Night
• CS/C-Mount
• Power Source : DC 12V
• Power Consumption : Max 400mA (DC 12V)
6

3. COMPONENTS
HD CCTV
Digital Video Camera
AUTO IRIS LENS
CONNECTION PLUG
C-MOUNT ADAPTOR RING
OPERATION MANUAL
Terminal Block
7

4. NAME AND FUNCTION
• FRONT
8
TRIPOD MOUNTING HOLE(1/4"-20 UNC)
AUTO IRIS JACK
MOUNT COVER
C-MOUNT
ADAPTOR RING
TRIPOD MOUNTING HOLE(1/4"-20 UNC)
BACK FOCUS CONTROL LEVER

4. NAME AND FUNCTION
• BACK
①. MENU BUTTON
②. UP BUTTON
③. DOWON BUTTON
④. LEFT BUTTON
⑤. RIGHT BUTTON
⑥. POWER LED
⑦. SDI OUT JACK
⑧. VIDEO OUT JACK
⑨. MIC IN JACK
⑩. AUDIO OUT JACK (TBD)
⑪. TERMINAL (POWER, RS-485, Digital Input/Output)
9
① ②
③
④
⑤
⑥
⑦
⑧
⑨⑩
⑪

10
5. INSTALLATION
• LENS CONNECTION
Lenses are sold separatele. Lenses such as an auto iris lens,
CS-Mount lens and C-Mount lens can be used.
NOTE
• Please keep the lens clean.
• Any foreign objects and Finger marks on the lens can cause
inferior image quality in low light level conditions.
When using an auto iris lens
1. Please peel off about 8mm of the outer skin of the auto iris lens cable.
2. Please peel off about 2mm of the outer skin of the insulated conductor
inside the lens cable.

11
5. INSTALLATION
3. Please remove the cover of the auto iris lens connection plug and
solder the lens cable to the connector pin in the plug.
* PIN ASSIGNMENT OF THE LENS CONNECTOR
1) Video auto iris lens
Pin 1: Power source(DC 12V)
Pin 2: N.C(Not used)
Pin 3: Video signal
Pin 4: Shield, GND(Ground)
2) DC auto iris lens
Pin 1: DAMP-(CTL-)
Pin 2: DAMP+(CLT+)
Pin 3: DRV+
Pin 4: DRV-(GND)
4. Please replace the auto iris lens connection plug cover and take off the
Sensor protection cap and then attach the auto iris lens to the camera by
screwing it in clockwise.

5. INSTALLATION
5. Please insert the connection plug that is connected to the auto iris lens
cable into the auto lens connector, which is located on the side of the camera
12
C-mount lens : 10mm or less
CS-mount lens : 5mm or less
*NOTE
Use the lens under the specification as shown. Otherwise
the lens can damage the camera or abnormal fixing may
result.

5. INSTALLATION
Installation of C-Mount Lens
Installation of CS-Mount Lens
13
C-MOUNT ADAPTOR RING

14
5. INSTALLATION
• MONITOR CONNECTION
DC12V REGULATED
POWER SUPPLY
BNC FEMALE
VIDEO
VIDEO IN
HD SDI IN
SDI
RECEIVER
DISPLAY
DEVICE
TV
MONITOR

15
6. DIMENSIONS
Unit(mm)
145(C-Mount)
138.55(C-Mount)
AUTO IRIS JACK
TRIPOD MOUNTING HOLE
C-MOUNT ADAPTOR RING
72.58
66
TRIPOD MOUNTING HOLE
(1/4"-20 UNC, Depth 5)

16
7. SPECIFICATION
Image Device 1/3” SONY Color CMOS
Effective Pixels 1329 (H) x 1049 (V) 30fps
Unit cell size 3.63um (H) x 3.63um (V)
Video output mode SDI : 720p 30, 720p 60, 720p 25, 720p 50
TV Out : NTSC / PAL selectable
H.Resolution more than 600 TV Line
Minimum illumination 1.0 Lux
S/N Ratio Max 50dB
Shutter speed Auto / Manual selectable
Min. Exposure Time 110.86us (1/9020 sec)
Flickerless Off / 60Hz(50Hz) selectable
True Day/Night IR Cut /Pass Filter change
White Balance ATW / Push / Manual
BLC On/Off (by OSD)
Lens Control Manual Iris, DC Iris (or Video Iris) (factory setting only)
OSD Menu Yes
Power DC 12V
Consumption Max 400mA(Without TDN 360mA)
Dimension (W x H x D) 72.5mm x 66mm x 138.5mm
Weight 420g
Lens Mount CS/C-mount
Conformity CE, FCC
Temperature/Humidity
(no condensing)
Operation : -10~50 / 20~80%
Storage : -20~70 / 20~95%

17
8. DIGITAL INPUT/OUTPUT
• Digital Input Port / Sensor Input
• Digital Output Port
CAMERA
EXTERNAL DEVICE
DI
MicroController
A/D Port
10bit resolution,
Vtop = 3.3V, Vbot = 0V
Sensor Input
(0~3.3V)
R:1.5K
CAMERA EXTERNAL DEVICE
MicroController GPOUT PORT
(3.3V)
3.3V
DO
R:270 Photo
Coupler
R:10K
Digital Output
(0/3.3V)
Day and Night
CDS MODE
GPIN PORT
(3.3V) Digital Input Port
Digital Output Port

18
9. OSD MANUAL
• Menu structure
- Main Menu
- VIDEO OUT Menu
SPECIAL
VIDEO OUT
LENS
EXPOSURE
WHITE BALANCE
DAY / NIGHT
IMAGE
VIDEO OUT SDI FORMAT
TV OUT FORMAT NTSC / PAL
720p 30Hz / 720p 60Hz
720p 25Hz / 720p 50Hz

19
9. OSD MANUAL
- LENS Menu
- EXPOSURE Menu
LENS LENS TYPE
BRIGHTNESS 0 ~ 255
DC IRIS(VIDEO IRIS)
IRIS SPD 0 ~ 112
DC IRIS(VIDEO IRIS) / MANUAL IRIS
MANUAL
EXPOSURE BRIGHTNESS
SHUTTER MODE
SHUT LEVEL 0~215
AUTO / MANUAL
/ FLK 60Hz(FLK 50Hz)
AGC MAX
DSS
BLC
0 ~ 255
OFF, 1 ~ 16
ON / OFF
0 ~ 255

20
9. OSD MANUAL
- WHITE BALANCE Menu
- DAY / NIGHT Menu
WHITE BALANCE MODE
R GAIN 0 ~ 255
MANUAL
B GAIN 0 ~ 255
ATW / PUSH / MANUAL
DAY / NIGHT MODE
DAY LEVEL 0 ~ 127
AUTO / EXT
NIGHT LEVEL 0 ~ 127
COLOR / AUTO / EXT / BW

21
9. OSD MANUAL
- IMAGE Menu
- SPECIAL Menu
IMAGE SHARPNESS
IMAGE FLIP
DNR
GAMMA
OFF, H, FLIP, V FLIP, H/V FLIP
OFF, LOW, MID, HIGH
OFF, 1.0, 1.8, 2.2, 2.6
0 ~ 15
SPECIAL SYSTEM INFO
USER SET
COMM/GPIO SET
FOCUS MODE
LANGUAGE
SAVE USER SET
LOAD USER SET
CLEAR USER SET
FACTORY RESET
CAMERA RESET
RS485 Address
GP IN Status
GP OUT Control
0~255
LOW / HIGH
ON / OFF