Kuppersbusch IKDU 9900.0PW Quick guide

Installation and instruction manual
IKDU 9900.0PW

Important notes
Miscellaneous
This installation instruction contains important information, read it carefully and follow any
instructions. This will prevent failure caused by wrong use and/or installation. Keep this
manual for possible later use. Follow the instructions from the manufacturer of the cooking
equipment for the installation of hoods. Install this hood with at least two people. Replace
defective parts only with original spare parts from the manufacturer.
If you have bought a cooker hood with an external motor then you will find more
information in the manual for the motor which is to be found in the package.
Safety requirements
Please note that the installation should only be done by a professional as he has the
knowledge about the air duct and the electrical connection. Make sure that the wall or
ceiling is suitable for the weight of the cooker hood. For fixing the cooker hood please use
the enclosed plugs. Depending on the surface the plugs (8mm) are having the following
bearing capacities:
brick 5,2 kN
concrete 9,4 kN
lime sand brick 4,8 kN
If you need to fix your cooker hood on other surfaces please ask a professional.
Risk of injury
During manufacturing of the extractor, sharp edges can be formed. Therefore always wear
gloves during installation.
Danger of electric shock
Voltage must match the voltage marked on the ratings plate. This plate can be found under
the grease filter. This appliance should be connected to a grounded system. The electrical
connection must be easily accessible after installation.
Before any maintenance or repair the power supply must be disconnected!
Air outlet
The air should not be discharged into a chimney which is also used for the removal of
exhaust gases from equipment working on fuel (including gas). Take into account the rules
for air outlet. Prepare electrical connection and ducting, that way the hood can easily be
connected. Avoid sharp bends and kinks in the drain hose.

Mounting above a stove
Furnace for solid fuels
In a solid fuel stove which can fire out (sparks) is the fitting of the hood only allowed when
the furnace is closed and its shielding is not removable.
Gas stove
The minimum distance between the gas stove and the cooker hood is 750mm. If the
manufacturer of the stove is recommending a lager distance please follow this advise.
Electric hob
The minimum distance between the gas stove and the cooker hood is 650mm. If the
manufacturer of the stove is recommending a lager distance please follow this advise.
Gas hob
The installation of the gas hob with a minimum distance of 750mm to the cooker hood is
only allowed if the following, single values for the thermal load are not exceeded.
load of one cooking zone max. 3,0 kW
load of all cooking zones max. 8,3 kW
load of the cooker max. 3,9 kW
Always follow the installation requirements and instructions of the cooker manufacturer!
Control
The cooker hood has the following functions:
Button 1:low level
Button 2: average level
Button 3: high level
Button 4: intensive level, after 3 minutes it will automatically switch back to high speed.
Button 5: Automatic delay stop – Pressing this key will switch the motor to highest
speed, after every three minutes it will switch to an lower speed until it switches off.
Button 6: light on/off
Button 7: Grease filter saturation indicator – when lit the grease filter must be cleaned,
after cleaning the light can be reset by pressing and holding the key for 5 seconds.

Grease filter
Reset of grease filter saturation indicator
After cleaning the grease filter press button 7 for 5 seconds to reset the electronic.
Removal of grease filter
Dismount the grease filter by pulling it down by its two knobs and remove the safety
cable. Attention! When reinstalling the grease filter please do not forget to connect the
safety cable!
Grease filter cleaning
Dismount the grease filter by pulling it down by its two knobs and remove the safety
cable. The grease filter can be cleaned in the dishwasher, it is possible that it’s surface
slightly fade!
Important: Highly saturated filters should not be cleaned together with the regular
dishes!
When cleaning the grease filter by hand, soak in a hot soapy water, then brush, rinse
and let drain.
Important:
-Only a fully dried filter should be put back in the appliance, this to prevent short circuit
-Clean the grease filter regularly, this will prevent later difficult cleaning.
-Don’t use 3-phase cleaners when cleaning the filter in a dishwasher. Don’t clean the
filters in a
professional dishwasher.
-Cleaning with aggressive products such as gasoline, acetone or trichloroethylene shall
be strongly discouraged.

Charcoal filter
Replacement of charcoal filter
As the charcoal filter is cleaning the exhaust air from grease and odours we recommend
to replace this filter every 3 to 6 months (depending on use of cooker hood). The
charcoal filter is placed under the motor. When replacing the filter please press in the
two fixing points (1) and pull out the filter. (see picture)
•disconnect main power
•remove grease filter
•unlock charcoal filter
•replace used charcoal filter
•set in new charcoal filter
•Attention!Never try to clean the charcoal filter with water!

Lighting
Bulb replacement
Faulty lamps should be replaced. Before changing the bulb disconnect the hood from
main power (pull the plug).
Lamps remain hot for a while, let them cool down before touching them.
-Disconnect main power.
-Remove the metal ring with a small screwdriver. (see photo 1) Attention! Don not
drop the glass cover.
-Remove the old bulb.
-Install a new bulb (type G4 (20 W)), hold it with a cloth. (Don not touch the bulb with
your skin!)
-Install the glass cover and metal ring.
Photo 1

Trouble-shooting
Check the following points before contacting the service department.

Installation instruction

Installation of the Küppersbusch cooker hood IKDU 9900.OPW
1. Determine the centre of the hood over the stove. Use a plumb to mark the centre of
the unit on the ceiling.
2. Mark the drilling holes with help of the ceiling fixing plate.
3. Drill holes for mounting the cooker hood (4xM8). Insert the plugs in the drilled holes
and screw the bolts in as far as they stick out 20mm.
4. Place the mounting plate on the bolts and fix it with help of the washers and nuts.
5. Fix the rods by tightening the set screws (M4).
6. Connect the cooker hood to the power supply.
7. Slide the ceiling plate on the rods and fix it with the spherical-head screws (M4).
Please tighten these screws with a screw driver by hand only!
8. After this mount the complete cooker hood with help of two people to the rods and
tighten the set screws (M4).
9. Finally connect the cable which comes out of the rod to the cooker hood.