Kusam-meco 287SVD User manual

®
®®
AN ISO 9001:2015 COMPANY
PERSONAL
SAFETY VOLTAGE DETECTOR
MODEL - 287SVD
USER MANUAL
G 17, Bharat Industrial Estate, T. J. Road, Sewree (W),
Mumbai - 400 015. INDIA. Sales Direct : 022-24156638, 27754546
Tel. : [phone]
Email : [email protected]
Website : www.kusamelectrical.com
®
LIST OF PRODUCTS
¬ Digital Multimeter ¬ Digital AC & AC/DC Clampmeter
¬ AC Clamp Adaptor ¬ AC/DC Current Adaptor
¬ Thermo Anemometer ¬ Thermo Hygrometer
¬ Distance Meter ¬ Digital Lux Meter
¬ Network Cable Tester ¬ Power Factor Regulator
¬ Earth Resistance Tester ¬ Digital Panel Meters
¬ DC Power Supplies ¬ High Voltage Detector
¬ Calibrators ¬ Gas Analysers
¬ Frequency Counter ¬ Function Generator
¬ Phasing Sticks ¬ Battery Tester
¬ Waterproof Pen Testers ¬ Solar Power Meter
¬ EMF Detector
¬ Wood, Paper & Grain Moisture Meter
¬ Transistorised Electronic Analog & Digital Insulation
Resistance Testers(upto 10 KV)
¬ Digital Sound Level Meter & Sound Level Calibrator
¬ Digital contact & Non-contact Type Tachometer
¬ Digital Non-contact (infrared) Thermometer
¬ Maximum Demand Controller/Digital Power Meter
¬ Digital Hand Held Temperature Indicators

®
®
INTRODUCTION
The personal safety voltage detector is a sensor for
sensing AC High Voltage. It provides electric engineering
personnel, power engineering personnel, firefighting
personnel & instrument equipment workers with
prominent warning when approaching high voltage & for
taking necessary safety action, preventing illusion &
misjudgment which could lead to electric shock to person.
When a person wearing the personal safety voltage
detector is approaching high voltage source or
equipment, the sensor will detect automatically &
buzzer will generate a “BeBe” sound for warning & LED
will flash to remind operators that the user is approaching
a high voltage sauce & special attention shall be given
to the safety of operations.
01
● Equipped with self-testing functions.
● Sound & flash light warning on different frequencies
varied positively with sensed voltages.
● Able to sense all kinds of AC High Voltage System.
● Low power consumption.
● Meets : EN61326-1
● CE Certified.
● Voltage Detection:
02
FEATURES
● Designed for detecting un-shielded cables. If the
shielding of the cable is connected to the ground,
it can’t work.
● Compact, easy to wear & convenient in use.
● Usable both indoor & outdoor.
● Water-proof design IP65.
Voltage
6.6kV
(3.8kV phase to ground) 90°
11.4kV
(6.6kV phase to ground)
19.7kV
(11.4kV phase to ground)
22.8kV
(13.2kV phase to ground)
Detection
Angle
90°
90°
90°
40cm ± 20%
55cm ± 20%
80cm ± 20%
85cm ± 20%
Detection
distance

®
®
● Distance of starting warning:
85cm for 22.8kv (phase to phase)
● Applicable Frequency : 50 / 60Hz
● 110V ~ 22.8kV
● Volume : >70dB at 1 meter distance
● Operating Temp & Humidity :
0°C ~ 40°C / 80% R.H. Max.
● Outside Dimensions : 61(L) x 62(W) x 18.5(D)mm
● Weight : 70g. (including battery)
● Battery to use : Cr2032 x 1
● Battery Life : 50 hours for continuous use
● Accessories : user manual, Elastic cord x 2, Battery,
Hook x 3, Elastic cord adjustment x 1,
Connection ring x 2.
SPECIFICATION
03 04
METHOD OF USE
1. Inspection before use
(1) Check the appearance & structure for any
abnormality.
(2) Press Self-Test switch (about 10 seconds) to
confirm all functions are working normally.
(3) To be careful & to avoid misjudgment, test the
unit by contacting AC 110V insulated wire with
its front side to see if it sounds and flashes.
2. Wearing
(1) Wear the unit in front of the safety helmet.
3 hooks hold the
elastic cord around the
safety helmet.
Hook x 3

®
®
05 06
The effect is best when the sensing side is facing high
voltage in right angle (90 Deg.). When it is worn at
the inner side of arm or is covered by cloth, the
sensitivity is poor.
(3) Wear the unit to the outer side of forearm with the
sensing side faces outwardly.
2. Replacing Battery :
1. When the sound become weak, the battery
shall be replaced.
2. Use coin to open battery cover & remove used
battery. Place new battery into slot with the
battery positive (+) face up and fasten battery
cover with coin.
CAUTIONS
1. This instrument is an auxiliary testing unit & is only
for obtaining warning as additional protection.
Never use this instrument as substitution for Tester.
Electrical Test shall be the prime electric testing
instrument.
2. Other than affected by now you wear, the sensing
and warning distance may be influenced by
direction of electric article, ambient environment,
shielding objects and weather conditions.
3. Buzzer has inner water-proof film. Do not pierce it
with sharp article.
1. Sensing side shall maintain clean. The case may
be cleaned with soft fabric and mild detergent. No
solvent or corrosive agent may be used.
CLEANING & REPLACING BATTERY

®
®
4. Do not store this instrument outdoor or inside of car
for long time to avoid direct sunbeam & high
temperature.
5. The instrument shall not be dropped or impacted
heavily. If such situation does happen, perform
inspection and self-test to ensure no damage
occurred before using again.
6. If the instrument is rinsed by rain, remove battery
& place it at cool place for natural dry.
7. The personal safety voltage detector can’t detect
the HV cable which has an outer sheathing that
is connected to the ground.
07 08
COMBINATION OF THE DETECTOR
● Separate the elastic cord and the elastic cord
adjustment.
● The connection ring can be assembled.
Elastic cord adjustment

®
®
● The hook can be disassembled.
(1) The combination of the hook,
(2) The hook can be adjusted according to the user’s
requirement.
Sealed
for stuck
Follow the GAP
Up
Adjustment
Down
09 10
1. Before assembling the connection ring, take the
upper part of the connection ring pass through the
elastic cord & one side of the detector. Assemble
the connection ring firmly.
“A” Side
“A” Side
“A” Side

®
®
11 12
● Attention : this elastic cords strip must be “A” side
“B”
THICK
THIN
Correct
Incorrect
Stuck !!
2. Take three buckles pass through the elastic cord
from “B” side.
3. Turn over the elastic cord & take the elastic cord
adjustment pass through from “B” side.

®
®
13 14
4. First assemble the connection ring of the other side.
6. Turn over the elastic cord pass through the elastic
cord adjustment as below.
5. Take the elastic cord “B” side pass through the
space of the connection ring as below.
● Attention :
The second combination
is different.
7. Use the elastic cord adjustment to adjust the length
of the elastic cord, then assemble the hooks.
8. Fix the detector to the helmet.

®
15 16
SHORT ELASTIC CORD
● Before assembling the connection
ring, take the upper part of the
connection ring pass through
the elastic cord and one side of the
detector. Assemble the connection ring firmly.
● Assemble the
connection ring
of the other side
of the elastic cord.
MUMBAI
TEST CERTIFICATE
PERSONAL SAFETY VOLTAGE DETECTOR
This Test Certificate warrantees that the product has
been inspected and tested in accordance with the
published specifications.
MODEL NO. ___________
287SVD
SERIAL NO. ___________
DATE: ___________
ISO 9001
REGISTERED
QC
PASS
KUSAM-MECO
®

®
17 18
®
WARRANTY
Each “KUSAM-MECO” product is warranted to be free from
defects in material and workmanship under normal use & service.
The warranty period is one year (12 months) and begins from the
date of despatch of goods. In case any defect occurs in
functioning of the instrument, under proper use, within the
warranty period, the same will be rectified by us free of charges,
provided the to and fro freight charges are borne by you.
This warranty extends only to the original buyer or end-user
customer of a “KUSAM-MECO” authorized dealer.
This warranty does not apply for damaged Ic’s, fuses, burnt PCB's,
disposable batteries, carrying case, test leads, or to any product
which in “KUSAM-MECO’s” opinion, has been misused, altered,
neglected, contaminated or damaged by accident or abnormal
conditions of operation or handling.
“KUSAM-MECO” authorized dealer shall extend this warranty on
new and unused products to end-user customers only but have no
authority to extend a greater or different warranty on behalf of
“KUSAM-MECO”.
“KUSAM-MECO’s” warranty obligation is limited, at option, free of
charge repair, or replacement of a defective product which is
returned to a “KUSAM-MECO” authorized service center within
the warranty period.
All transaction are subject to Mumbai Jurisdiction.
THIS WARRANTY IS BUYER’S SOLE AND EXCLUSIVE
REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. “KUSAM-MECO”
SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT,
IN C I D EN TAL O R C O NS E Q U EN TI A L D A MA GE S OR
LOSSES, INCLUDING LOSS OF DATA, ARISING FROM ANY
CAUSE WHATSOEVER.
G 17, Bharat Industrial Estate, T. J. Road, Sewree (W),
Mumbai - 400 015. INDIA. Sales Direct : 022-24156638, 27754546
Tel. : [phone]
Email : [email protected]
Website : www.kusamelectrical.com
®