KWIK GOAL 7E201 User manual

NZ328 Rev. 10/05/11
ASSEMBLY INSTRUCTIONS FOR 7E201 PORTABLE BACKSTOP
1. Unpack all parts and check for damage that may have occurred during shipping. If damage has occurred,
notify trucking company immediately. Lay out all parts. Remove all cardboard and packaging immediately.
Wet or damp packaging may damage contents.
2. Read through entire instruction before beginning assembly and installation.
140 Pacific Drive Quakertown, PA 18951
(P) 215-536-2200 / (P) 800-531-4252 / (F) 215-536-4309 / (F) 800-778-8869
Visit our website @ kwikgoal.com
2011 Kwik Goal Ltd.
All Kwik Goal products carry a Lifetime Guarantee. For help with
guarantee issues, visit kwikgoal.com and click on the Lifetime
Guarantee logo or contact customer service at 1-800-531-4252.
Parts
WARNING
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT OF HIGH WINDS.
ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S LIFETIME GUARANTEE. DO NOT
LEAVE THIS EQUIPMENT UNATTENDED.
Base (4)
(Part# UZ1279)
Brace (2)
(Part# UZ1295)
Heavy Duty
Anchor Bage (16)
(Part# 10B7011)
Bottom Bar (3)
(Part# UZ1280)
234-1/2”
Upright (4)
(Part# UZ1278)
186”

Knob (2)
(Part#VZ252)
WARNING
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT OF HIGH WINDS.
ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S LIFETIME GUARANTEE. DO NOT
LEAVE THIS EQUIPMENT UNATTENDED.
Phillips Screw Driver
Assembly Tools
3. Attach swivel connector tube to all bases
as shown.
NOTE: Tighten 3/8” lock nuts only until
flush with end of carriage bolts.
Pulley Assembly (4)
(Part# TZ214, TZ339 & VZ80)
Net (1)
(Part# 3B4901)
Net Clip (40)
(Part# VZ116)
Snap Link (4)
(Part# VZ82)
Hardware
8-32 X 5/8” Flat Head Screw (Part# TZ314) (8)
1/4” Flat Washer (Part# TZ147) (4)
1/4” Lock Nut(Part# TZ19) (4)
3/8” Flat Washer (Part# TZ189) (6)
3/8” Lock Washer (Part# TZ301) (2)
3/8” Nut (Part# TZ166) (2)
3/8” Lock Nut (Part# TZ197) (4)
3/8” X 3” Threaded Stud (Part# TZ337) (2)
3/8” X 3-1/2” Carriage Bolt (Part# TZ340) (4)
27’ Rope (Part# VZ377) (4)
Note: Hardware may be packaged separately
in one or more boxes. Open all packages
before beginning assembly.
NZ328 Rev. 10/05/11
Net Holder (8)
(Part# VZ431)
Square Nut & Stud (2)
(Part# TZ336)
Base
3/8” Lock Nut
Swivel Connector Tube
3/8” Flat Washer
3/8” X 3-1/2” Carriage Bolt
Swivel Connector Tube (4)
(Part# UZ1296)
7/16” & 9/16”
Wrenches
Rope Cleat (4)
(Part# VZ569)

WARNING
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT OF HIGH WINDS.
ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S LIFETIME GUARANTEE. DO NOT
LEAVE THIS EQUIPMENT UNATTENDED.
NZ328 Rev. 10/05/11
4. Set assembled bases and bottom bars in desired
location and connect together.
Note: Bases at each end of unit must be
connected to the fixed tube of the base assembly.
Assembled Base
Bottom Bar
Bottom Bar
Bottom Bar
Assembled Base
Assembled Base
Assembled Base
Assembled Base
Bottom Bar
Fixed Tube
Square Nut & Stud
Assembled Base
Fixed Tube
Bottom Bar
Square Nut & Stud
Assembled Base
Bottom Bar
Bottom Bar

Heavy Duty Anchor Bag
Assembled Base
Heavy Duty Anchor Bag
Assembled Base
WARNING
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT OF HIGH WINDS.
ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S LIFETIME GUARANTEE. DO NOT
LEAVE THIS EQUIPMENT UNATTENDED.
NZ328 Rev. 10/05/11
5. Fill each of the 16 heavy duty anchor bags with
40lbs of sand or gravel. Set 4 heavy duty anchor
bags on each assembled base as shown.
6. Attach parts to uprights as shown.
Note: The pulley assembly is on the opposite side of
rope cleat.
Pulley Assembly
1/4” Lock Nut
1/4” Flat Washer
Upright
Upright
Top
Bottom
8-32 X 5/8” Flat Head Screw
Bottom
Top Rope Cleat

WARNING
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT OF HIGH WINDS.
ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S LIFETIME GUARANTEE. DO NOT
LEAVE THIS EQUIPMENT UNATTENDED.
NZ328 Rev. 10/05/11
Upright
Upright
Upright
Upright
Assembled Base with
Heavy Duty Anchor Bags
Upright
Pulley
Rope
Upright
Upright
Upright
Upright
Assembled Base with
Heavy Duty Anchor Bags
7. Lay out uprights as shown and put rope through
pulleys on each upright. Tie a snap link to the
end of each rope as shown.
Assembled Base with
Heavy Duty Anchor Bags
Upright
8. Lift upright onto assembled weighted bases,
making sure to keep rope from pulling out of
pulley.

WARNING
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT OF HIGH WINDS.
ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S LIFETIME GUARANTEE. DO NOT
LEAVE THIS EQUIPMENT UNATTENDED.
NZ328 Rev. 10/05/11
9. First attach 3/8” X 3” threaded stud to
brace on plate with threaded hole. With
square nut & stud, attach braces to
bottom bar using knob & 3/8” lock nut.
NOTE: Tighten 3/8” lock nuts only until
flush with end of stud so knob can turn.
Loosen knob to slide brace to hold
upright and when upright is plumb
tighten knob to hold brace in place.
Knob
Bottom Bar
Upright
Bottom Bar
Square Nut & Stud
3/8” Nut
3/8” Lock Nut
3/8” Lock Washer
3/8” Flat Washer
3/8” X 3” Threaded Stud
Threaded Plate
Brace
Knob
Net
Snap Link
Rope
Top Corner Tag
Net
10.Lay out net out as shown. Clip rope to net in 4
locations.
Threaded Plate
Upright
3/8” X 3” Threaded Stud
Brace

Net
Rope
Rope Cleat
Upright
Net Holder
Top Corner Tag
17”
17”
WARNING
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT OF HIGH WINDS.
ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S LIFETIME GUARANTEE. DO NOT
LEAVE THIS EQUIPMENT UNATTENDED.
NZ328 Rev. 10/05/11
11.Hoist net starting at one end and attach net
holder to the perimeter rope of net
approximately 17” from the top corner. Then
wrap net holder around upright and attach
to the perimeter rope again 17” from the
first clip.
12.Hoist net up enough to attach the next net holder and
repeat step 11 until net is hoisted to the top of upright.
Repeat step 11 & 12 for other end upright.
Net

WARNING
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT OF HIGH WINDS.
ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S LIFETIME GUARANTEE. DO NOT
LEAVE THIS EQUIPMENT UNATTENDED.
NZ328 Rev. 10/05/11
13.Complete net raising by hoisting net on two center poles. To
secure bottom of net, attach net to bottom bar of backstop
with net clips. Place perimeter rope of net in clip and put
base of clip into channel and turn 90 degrees to lock into
place. Space net clips even through out base, see below for
approximate spacing.
CAUTION: BE SURE THAT BACKSTOP IS PROPERLY
ANCHORED BEFORE ATTEMPTING TO ATTACH NET.
20”
Net Clip
Bottom Bar
Perimeter Rope
Net Clip

180 TO 90 180 TO 90
WARNING
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE OR IN THE THREAT OF HIGH WINDS.
ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S LIFETIME GUARANTEE. DO NOT
LEAVE THIS EQUIPMENT UNATTENDED.
NZ328 Rev. 10/05/11
14.This unit can be set up to conform to irregular boundaries, such as arcs.
15.After first assembly this unit can be disassembled
without any tools. Loosening the knob allows
braces to slide in and out of bottom bar.
CAUTION: REMOVE NET AND UPRIGHT BEFORE
ADJUSTING ANGLES. DO NOT MOVE UNIT WHEN
FULLY ASSEMBLED THIS COULD CAUSE INJURY
OR DEATH.
OVER HEAD VIEW
Knob
Bottom Bar