KWIK GOAL PRO PREMIER 2B9006 User manual

ASSEMBLY INSTRUCTIONS FOR 2B9006 & 2B9006SW PRO PREMIER COPA GOAL
NOTE: Components may be packaged in one or more additional boxes.
2. Read through entire instruction before beginning assembly and installation.
1. Unpack all parts and check for damage that may have occurred during shipping. If damage has
occurred, notify Kwik Goal immediately. Lay out all parts. Remove all cardboard and packaging
immediately. Wet or damp packaging may damage contents.
140 Pacific Drive Quakertown, PA 18951
(P) 215-536-2200 / (P) 800-531-4252 / (F) 215-536-4309 / (F) 800-778-8869
Visit our website @ kwikgoal.com
2016, Rev. 2019 Kwik Goal Ltd.
Right Post (1)
(Part# UZ649)
Left Post (1)
(Part# UZ1527)
Parts
NZ391 Rev. 07/15/19
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties.
®
280”
Crossbar (2)
(Part# UZ393)
280”
Back Bottom Bar (1)
(Part# UZ966) 100-3/8” 100-3/8”

140 Pacific Drive Quakertown, PA 18951
(P) 215-536-2200 / (P) 800-531-4252 / (F) 215-536-4309 / (F) 800-778-8869
Visit our website @ kwikgoal.com
1998 rev 2009 Kwik Goal Ltd.
2. Safety/Warning labels must be clearly visible.
IMPORTANT GOAL SAFETY INSTRUCTIONS
READ CAREFULLY
1. Check for structural integrity and proper connecting hardware before every
use. Replace damaged or missing parts or fasteners immediately.
3. Securely anchor moveable soccer goals at ALL times.
4. Always instruct players, managers, coaches, trainers, teachers, maintenance
workers and all other personnel who might come in contact with the goal,
on the safe handling of and potential dangers associated with moveable
soccer goals.
5. Always exercise extreme caution when moving goals and provide adequate
manpower to move goals of varied sizes and weights. Moveable soccer goals
should only be moved by authorized personnel.
6. NEVER allow anyone to climb on the net or goal framework.
7. Moveable soccer goals should only be used on LEVEL fields, NEVER on a
slope or hill area.
8. Remove nets when goals are not in use.
9. Most of the tip-over injuries occurred when goals were unattended. Anchor
or chain one goal to another or to nearby fence posts, dugouts, or any other
similar sturdy fixture when not in use. If this is not practical, store moveable
soccer goals in a place where children cannot have access to them.
10. Fully disassemble goals for seasonal storage.
NZ391 Rev. 07/15/19

Chain (4)
w/ Snap Link & Anchor Plate
(Part# UZ846 )
Back Pole Brace (2)
(Part# UZ1526)
Back Pole Brace (2)
(Part# UZ1525)
Post Brace (2)
(Part# UZ737)
Anchor Bag (6)
(Part# 10B1605)
Ground Anchor (4)
w/hardware
(Part# 10B101 Set of 4)
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties. NZ391 Rev. 07/15/19
Back Pole (2)
(Part# UZ1524)
Net (1)
(Part# 3B1502)
Red Dot Blue Dot
Back Bottom Bar
Connector (2)
(Part# UZ1033)
Back Pole Cap (2)
(Part # VZ719)
Tamper Resistant
Net Clip (100)
(Part# 10B3401 Pack of 100)
Net Clip Driver (1)
(Part# VZ140)
Left Base (1)
(Part# UZ1520)
100-3/8”
Right Base (1)
(Part# UZ1521)
100-3/8”
Channel Spacer (8)
(Part# UZ812)
Bolt Cap (4)
(Part# VZ751)

Net Rope
Assembly (2)
(Part# JZ215 Pack of 2
w/ Snaplink)
Any modifications to this or any Kwik Goal product will void any and all warranties.
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
NZ391 Rev. 07/15/19
7/16” Lock Nut (Part# TZ47) (4)
Hardware
Note: Hardware may be packaged separately
in one or more boxes. Open all packages
before beginning assembly.
7/16” X 6” Hex Bolt (Part# TZ380) (4)
7/16” Flat Washer (Part# TZ171) (8)
3/8“ x 1-3/4” Hex Bolt (Part# TZ227) (16)
3/8" x 7/8" Hex Bolt (Part# TZ249) (18)
3/8” x 5/8” Hex Bolt (Part# TZ383) (4)
5/16" X 1” Hex Bolt (Part# TZ121) (8)
5/16" Flat Washer (Part# TZ269) (8)
3/8“ Lock Washer (Part# TZ65) (36)
3/8“ Flat Washer (Part# TZ60) (40)
3/8" Square Nut (Part# TZ247) (22)
5/16" Lock Washer (Part# TZ122) (8)
1/4" X 2” Eye Bolt (Part# TZ381) (2)
1/4" Lock Nut (Part# TZ19) (2)
1/4"Flat Washer (Part# TZ361) (2)
Ratchet with
7/16” ,1/2”, 5/8”,
9/16” & 3/4”
Sockets
9/16
7/16”, 1/2”, 5/8”,
9/16” & 3/4”
Wrenches
Rubber Mallet
Assembly Tools
Knob w/o Threads (4)
(Part# VZ687)
280”
Pole Rope
Assembly (4)
(Part# JZ222 Pack of 4)
112”

4. Insert one square nut in each of the assembled posts.
3. Attach left post and right post to crossbar using channel spacers and 3/8” hex bolts. Note direction of decals
before fastening. Be sure connections are pressed firmly together before tightening hex bolts.
Left Post
Right Post
Crossbar
Decals
3/8” Square Nut
3/8” X 1-3/4” Hex Bolt
Channel Spacer
3/8” Flat Washer
Right Post
3/8” Lock Washer
Crossbar
Any modifications to this or any Kwik Goal product will void any and all warranties.
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
NZ391 Rev. 07/15/19

5. Attach base to crossbar and bottom back bar as shown.
Note direction of decals before fastening. Assemble all
hardware first, then go back and tighten each bolt. Be
sure connections are pressed firmly together before
tightening hex bolts.
6. Using a rubber mallet, install bolt caps on exposed threads of
7/16” X 6” hex bolts.
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties.
Left Base
Back Bottom Bar Crossbar
Right Base
Decals
Channel Spacer
3/8” X 1-3/4” Hex Bolt
3/8” Lock Washer
3/8” Flat Washer
3/8” Square Nut
Left Base Crossbar
3/8” Square Nut
Bolt Cap
Bolt Cap
Rubber Mallet
NZ391 Rev. 07/15/19
Back Bottom Bar
7/16” X 6” Hex Bolt
Channel Spacer
Left Base
7/16” Flat Washer
7/16” Lock Nut
3/8” X 1-3/4” Hex Bolt
Back Bottom Bar
Back Bottom Bar Connector
3/8” Lock Washer
3/8” Flat Washer

***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties. NZ391 Rev. 07/15/19
Crossbar
Base
Base
Crossbar
Left Post
Right Post
7. Lift assembled posts and insert into assembled bases. Be sure connections are pressed firmly together before
tightening bolts. Be sure to tighten both bolts on each post brace.
Base
3/8” Square Nut
3/8" X 7/8"
Hex Bolt
Flat Washer
Lock Washer
Post Brace
Post
3/8" X 1-3/4"
Hex Bolt
3/8” Flat Washer
3/8” Lock Washer
Channel Spacer
3/8" X 1-3/4" Hex Bolt
3/8” Lock Washer
3/8” Flat Washer

8. If using swivel wheels (2B9006SW) - skip to step 10, for all other goals continue to step 9.
10B409), also include two threaded channel spacers from wheel option package in each base.
9. Insert two 3/8” square nuts into left base and right base. NOTE: If installing optional wheels (Part#
Any modifications to this or any Kwik Goal product will void any and all warranties.
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
NZ391 Rev. 07/15/19
Threaded Channel Spacer
(metal)
(for wheel option 10B409)
3/8” Square Nuts
Base

***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties.
10. Assemble back poles as shown. Make sure eyebolt is in slot before tightening. Do not overtighten.
NZ391 Rev. 07/15/19
1/4” X 2” Eyebolt
Back Pole
Cap
3/8” Square Nuts
1/4” Flat Washer
1/4” Lock Nut
Slot
3/8” X 5/8” Hex Bolt
Knob
3/8” Flat Washer
3/8” Square Nut
before installing in back pole.
TIP: Use square nut to draw hex bolt into knob

Tamper Resistant Net Clip
(2 Per Back Pole)
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties.
7 FT
Pole Ropes
Net Clip
Driver
Tamper Resistant Net Clip
Pole Rope Assemblies
Loops Around Knobs
Tamper Resistant Net Clip
7 FT
Knobs
11. Put loop end of pole ropes (2) through eyebolt and place rope in channel. With rope assemblies placed in
channel, insert tamper resistant net clips at locations shown.
NZ391 Rev. 07/15/19
Knobs