Kyocera FS-C8026N Assembly instructions

SERVICE
MANUAL
Published in Oct. '03
FS-C8026N

Revision history
Version Data Replaced Remarks
1.0 24-Oct.-2003
1.118-Dec.-2003-Overall revised

Safety precautions
This booklet provides safety warnings and precautions for our service personnel to ensure the safety of
their customers, their machines as well as themselves during maintenance activities. Service personnel
are advised to read this booklet carefully to familiarize themselves with the warnings and precautions
described here before engaging in maintenance activities.

indicates that action is required. The specific action required is shown inside the symbol.
General action required.
Remove the power plug from the wall outlet.
Always ground the copier.
Safety warnings and precautions
Various symbols are used to protect our service personnel and customers from physical danger and
to prevent damage to their property. These symbols are described below:
DANGER:High risk of serious bodily injury or death may result from insufficient attention to or incorrect
compliance with warning messages using this symbol.
WARNING:Serious bodily injury or death may result from insufficient attention to or incorrect compliance
with warning messages using this symbol.
CAUTION:Bodily injury or damage to property may result from insufficient attention to or incorrect
compliance with warning messages using this symbol.
Symbols
The triangle ( ) symbol indicates a warning including danger and caution. The specific point
of attention is shown inside the symbol.
General warning.
Warning of risk of electric shock.
Warning of high temperature.
indicates a prohibited action. The specific prohibition is shown inside the symbol.
General prohibited action.
Disassembly prohibited.

1. Installation Precautions
WARNING
•Do not use a power supply with a voltage other than that specified. Avoid multiple connections to
one outlet: they may cause fire or electric shock. When using an extension cable, always check
that it is adequate for the rated current. ............................................................................................
•Connect the ground wire to a suitable grounding point. Not grounding the copier may cause fire or
electric shock. Connecting the earth wire to an object not approved for the purpose may cause
explosion or electric shock. Never connect the ground cable to any of the following: gas pipes,
lightning rods, ground cables for telephone lines and water pipes or faucets not approved by the
proper authorities. .............................................................................................................................
CAUTION:
•Do not place the copier on an infirm or angled surface: the copier may tip over, causing injury. .....
•Do not install the copier in a humid or dusty place. This may cause fire or electric shock. ..............
•Do not install the copier near a radiator, heater, other heat source or near flammable material.
This may cause fire. ..........................................................................................................................
•Allow sufficient space around the copier to allow the ventilation grills to keep the machine as cool
as possible. Insufficient ventilation may cause heat buildup and poor copying performance. ..........
•Always handle the machine by the correct locations when moving it. ..............................................
•Always use anti-toppling and locking devices on copiers so equipped. Failure to do this may
cause the copier to move unexpectedly or topple, leading to injury..................................................
•Avoid inhaling toner or developer excessively. Protect the eyes. If toner or developer is
accidentally ingested, drink a lot of water to dilute it in the stomach and obtain medical attention
immediately. If it gets into the eyes, rinse immediately with copious amounts of water and obtain
medical attention. ..............................................................................................................................
•Advice customers that they must always follow the safety warnings and precautions in the copier’s
instruction handbook. ........................................................................................................................

•Check that the power cable covering is free of damage. Check that the power plug is dust-free. If
it is dirty, clean it to remove the risk of fire or electric shock. ............................................................
•Never attempt to disassemble the optical unit in machines using lasers. Leaking laser light may
damage eyesight. ..............................................................................................................................
•Handle the charger sections with care. They are charged to high potentials and may cause
electric shock if handled improperly. .................................................................................................
CAUTION
•Wear safe clothing. If wearing loose clothing or accessories such as ties, make sure they are
safely secured so they will not be caught in rotating sections...........................................................
•Use utmost caution when working on a powered machine. Keep away from chains and belts. .......
•Handle the fixing section with care to avoid burns as it can be extremely hot. .................................
•Check that the fixing unit thermistor, heat and press rollers are clean. Dirt on them can cause
abnormally high temperatures...........................................................................................................
•Do not remove the ozone filter, if any, from the copier except for routine replacement. ...................
2. Precautions for Maintenance
WARNING
•Always remove the power plug from the wall outlet before starting machine disassembly. ..............
•Always follow the procedures for maintenance described in the service manual and other related
brochures. .........................................................................................................................................
•Under no circumstances attempt to bypass or disable safety features including safety
mechanisms and protective circuits. .................................................................................................
•Always use parts having the correct specifications. ..........................................................................
•Always use the thermostat or thermal fuse specified in the service manual or other related
brochure when replacing them. Using a piece of wire, for example, could lead to fire or other
serious accident. ...............................................................................................................................
•When the service manual or other serious brochure specifies a distance or gap for installation of a
part, always use the correct scale and measure carefully. ...............................................................
•Always check that the copier is correctly connected to an outlet with a ground connection. ............

•Do not pull on the AC power cord or connector wires on high-voltage components when removing
them; always hold the plug itself. ......................................................................................................
•Do not route the power cable where it may be stood on or trapped. If necessary, protect it with a
cable cover or other appropriate item. ..............................................................................................
•Treat the ends of the wire carefully when installing a new charger wire to avoid electric leaks. .......
•Remove toner completely from electronic components. ...................................................................
•Run wire harnesses carefully so that wires will not be trapped or damaged. ...................................
•After maintenance, always check that all the parts, screws, connectors and wires that were
removed, have been refitted correctly. Special attention should be paid to any forgotten
connector, trapped wire and missing screws. ..................................................................................
•Check that all the caution labels that should be present on the machine according to the
instruction handbook are clean and not peeling. Replace with new ones if necessary. ...................
•Handle greases and solvents with care by following the instructions below: ....................................
·Use only a small amount of solvent at a time, being careful not to spill. Wipe spills off completely.
·Ventilate the room well while using grease or solvents.
·Allow applied solvents to evaporate completely before refitting the covers or turning the main
switch on.
·Always wash hands afterwards.
•Never dispose of toner or toner bottles in fire. Toner may cause sparks when exposed directly to
fire in a furnace, etc. ..........................................................................................................................
•Should smoke be seen coming from the copier, remove the power plug from the wall outlet
immediately. ......................................................................................................................................
3. Miscellaneous
WARNING
•Never attempt to heat the drum or expose it to any organic solvents such as alcohol, other than
the specified refiner; it may generate toxic gas. ................................................................................

This page is intentionally left blank.

2BF
CONTENTS
1-1 Specifications
1-1-1 Specifications..........................................................................................................................................1-1-1
1-1-2 Parts names............................................................................................................................................1-1-3
(1) Printer................................................................................................................................................1-1-3
(2) Operation panel.................................................................................................................................1-1-4
1-1-3 Cross section view ..................................................................................................................................1-1-5
1-2 Handling Precautions
1-2-1 Drum (process unit) ................................................................................................................................1-2-1
1-2-2 Installation environment ..........................................................................................................................1-2-1
1-3 Installation
1-3-1 Unpacking and installation .....................................................................................................................1-3-1
(1) Installation procedure ........................................................................................................................1-3-1
1-3-2 Installing expansion memory (optional) ................................................................................................1-3-10
1-3-3 Installing a memory card (optional).......................................................................................................1-3-11
1-3-4 Installing the network interface card (optional) .....................................................................................1-3-12
1-3-5 Installing the hard disk unit (optional) ...................................................................................................1-3-13
1-3-6 Installing the dehumidifier heater (optional) ..........................................................................................1-3-14
1-4 Maintenance Mode
1-4-1 Service mode ..........................................................................................................................................1-4-1
(1) Executing service mode ....................................................................................................................1-4-1
1-4-2 Maintenance mode ...............................................................................................................................1-4-12
(1) Maintenance mode..........................................................................................................................1-4-12
1-5 Troubleshooting
1-5-1 Paper misfeed detection .........................................................................................................................1-5-1
(1) Paper misfeed indication...................................................................................................................1-5-1
(2) Paper misfeed detection....................................................................................................................1-5-2
1-5-2 Self-diagnosis .........................................................................................................................................1-5-3
(1) Self-diagnostic function .....................................................................................................................1-5-3
(2) Self diagnostic codes ........................................................................................................................1-5-4
1-5-3 Electric problems ..................................................................................................................................1-5-25
1-5-4 Image formation problems ....................................................................................................................1-5-36
1-5-5 Mechanical problems ............................................................................................................................1-5-46
1-6 Assembly and Disassembly
1-6-1 Precautions for assembly and disassembly............................................................................................1-6-1
(1) Precautions .......................................................................................................................................1-6-1
1-6-2 Outer covers ...........................................................................................................................................1-6-2
(1) Detaching and refitting the top cover.................................................................................................1-6-2
(2) Detaching and refitting the rear cover ...............................................................................................1-6-5
(3) Detaching and refitting the eject cover (eject cover assembly) .........................................................1-6-6
1-6-3 Primary paper feed unit...........................................................................................................................1-6-7
(1) Detaching and refitting the primary paper feed unit ..........................................................................1-6-7
(2) Detaching and refitting the paper feed roller .....................................................................................1-6-9
(3) Detaching and refitting the lower paper feed pulley ........................................................................1-6-10
1-6-4 MP tray feed unit...................................................................................................................................1-6-11
(1) Detaching and refitting the MP tray feed roller and MP tray retard roller ........................................1-6-11
1-6-5 Transfer unit..........................................................................................................................................1-6-12
(1) Detaching and refitting the transfer unit ..........................................................................................1-6-12
1-6-6 Process section.....................................................................................................................................1-6-13
(1) Detaching and refitting the process unit ..........................................................................................1-6-13
(2) Detaching and refitting the drum unit and developer.......................................................................1-6-15
1-6-7 Fuser unit ..............................................................................................................................................1-6-17
(1) Detaching and refitting the fuser unit...............................................................................................1-6-17
(2) Detaching and refitting the upper and lower fuser thermistors, upper and lower fuser thermostats,
upper and lower fuser heater lamps and upper and lower fuser rollers ..........................................1-6-18
1-6-8 PWBs ....................................................................................................................................................1-6-25
(1) Detaching and refitting the main controller PWB.............................................................................1-6-25

2BF
(2) Detaching and refitting the engine controller PWB..........................................................................1-6-26
(3) Detaching and refitting the power supply PWB ...............................................................................1-6-27
(4) Detaching and refitting the main high voltage PWB ........................................................................1-6-29
(5) Detaching and refitting the bias high voltage PWB .........................................................................1-6-30
(6) Detaching and refitting the LPH drive PWB ....................................................................................1-6-31
(7) Detaching and refitting the front relay PWB ....................................................................................1-6-32
1-6-9 Others ...................................................................................................................................................1-6-33
(1) Detaching and refitting the developing MCY motor.........................................................................1-6-33
(2) Detaching and refitting the drum motors K, M, C and Y..................................................................1-6-34
(3) Detaching and refitting the toner motors K, M, C and Y..................................................................1-6-35
(4) Detaching and refitting the cassette lift motor .................................................................................1-6-36
(5) Detaching and refitting the paper feed motor ..................................................................................1-6-37
(6) Detaching and refitting the paper feed drive unit.............................................................................1-6-38
(7) Detaching and refitting the developing K/fuser motor .....................................................................1-6-39
(8) Detaching and refitting the ozone filter............................................................................................1-6-40
(9) Detaching and refitting the LED print head .....................................................................................1-6-41
(10) Adjusting the focus of the LED print head.......................................................................................1-6-44
2-1 Mechanical construction
2-1-1 Paper feed section ..................................................................................................................................2-1-1
(1) Paper cassette, primary paper feed unit and paper feeder feed section...........................................2-1-1
(2) MP tray feed unit and paper feed unit ...............................................................................................2-1-3
2-1-2 Process section.......................................................................................................................................2-1-5
(1) Developers and drum unit .................................................................................................................2-1-5
(2) Main charger unit...............................................................................................................................2-1-7
(3) LED print head ..................................................................................................................................2-1-8
2-1-3 Transfer section ....................................................................................................................................2-1-10
(1) Transfer unit ....................................................................................................................................2-1-10
2-1-4 Fuser section ........................................................................................................................................2-1-14
(1) Fuser unit ........................................................................................................................................2-1-14
2-1-5 Exit section............................................................................................................................................2-1-16
(1) Eject unit and face-down exit section..............................................................................................2-1-16
2-2 Electrical Parts Layout
2-2-1 Electrical parts layout..............................................................................................................................2-2-1
(1) Main front, upper, left, inner and paper cassette...............................................................................2-2-1
(2) Main rear ...........................................................................................................................................2-2-3
(3) Main right and primary paper feed unit..............................................................................................2-2-5
(4) Paper feed unit, MP tray unit and transfer unit..................................................................................2-2-6
(5) Process unit and fuser unit................................................................................................................2-2-7
2-3 Operation of the PWBs
2-3-1 Power supply PWB .................................................................................................................................2-3-1
2-3-2 Engine controller PWB............................................................................................................................2-3-4
2-4 Appendixes
2-4-1 Appendixes .............................................................................................................................................2-4-1
(1) Timing chart No.1 From the power switch turned on to machine stabilization ..................................2-4-1
(2) Timing chart No.2 Cassette paper feeding, Color printing, Paper size A4 ........................................2-4-2
(3) Timing chart No.3 Cassette paper feeding, Color printing, Paper size A3 ........................................2-4-3
(4) Timing chart No.4 MP tray paper feeding, Color printing, Paper size A4..........................................2-4-4
(5) Timing chart No.5 MP tray paper feeding, Color printing, Paper size A3..........................................2-4-5
(6) Timing chart No.6 Paper feeder PF-645 lower cassette paper feeding, Color printing,
Paper size A4....................................................................................................................................2-4-6
(7) Timing chart No.6 Paper feeder PF-645 lower cassette paper feeding, Color printing,
Paper size A3....................................................................................................................................2-4-7
(8) Wiring diagram ..................................................................................................................................2-4-8

2BF
1-1-1
1-1 Specific ations
1-1-1 Specifications
Type ................................................ Floor
Printing system ...............................Electrophotographic printing (tandem)
Paper type ...................................... Cassette: Plain paper (60 to 105 g/m2)
Recycled paper (105 to 220 g/m2)
Thick paper (90 to 105 g/m2)
Thin paper (60 to 64 g/m2)
MP tray: Plain paper (60 to 105 g/m2)
Recycled paper (60 to 90 g/m2)
Thick paper (105 to 220 g/m2)
Thin paper (60 to 64 g/m2)
Special paper: Transparencies, labels, envelopes, postcards, tracing paper
Paper sizes .....................................A4 (210 ×297 mm)
A3 (297 ×420 mm)
B4 (257 ×364 mm)
B5 (182 ×257 mm)
A5 (148 ×210 mm)
Letter (81/2" ×11")
Legal (81/2" ×14")
Non-standard size (148 to 216 mm ×210 to 420 mm: cassette), (70 to 305 mm ×148
to 457 mm: MP tray)
Print speeds....................................Cassette (Values within [ ] are for duplex printing using the duplexer DU-640.)
A4: 26 pages/minutes [24.5 pages/minutes]
B4: 13 pages/minutes [13 pages/minutes]
A3: 13 pages/minutes [13 pages/minutes]
Letter: 26 pages/minutes [24.5 pages/minutes]
Legal: 13 pages/minutes [13 pages/minutes]
MP tray (in cassette mode)
A4: 26 pages/minutes
B4: 13 pages/minutes
A3: 13 pages/minutes
Letter: 26 pages/minutes
Legal: 13 pages/minutes
First print time .................................Standby mode: 8.8 seconds or less (A4)
Warm-up time .................................Sleep mode: 180 seconds or less (room temperature 23 °C, 60% RH)
Paper feed system.......................... One universal cassette and one MP tray
Paper loading capacity ...................Cassette: 500 sheets (80 g/m2, 0.11 µm)
MP tray: 150 sheets (80 g/m2, 0.11 µm)
Paper eject system ............................ Face down: 500 sheets (80 g/m
2
, 0.11 µ m), equipped with a face-down paper full sensor
Face up: 150 sheets, Optional face-up tray PT-640 must be installed
Photoconductor...............................a-Si drum (diameter 30 mm)
Charging system.............................Scorotron (positive charging)
Light source .................................... LED (Advanced Beam Array)
Developing system ......................... Dual component dry developing method
Toner replenishing: Automatic from the toner container
Transfer system .............................. Primary transfer: Transfer belt (negative-charged)
Secondary transfer: Transfer roller (negative-charged)
Separation system ..........................Small diameter separation
Fixing system.................................. Heat roller system (Oil-less)
Heat roller (diameter 45mm, 600 W halogen heater lamp)
Pressure roller (diameter 45mm, 400 W halogen heater lamp)
Charge erasing system................... Exposure by eraser lamp (LED)
Cleaning system ............................. Drum: Counter blade
Primary transfer belt: Collecting to the drum by applying the reverse transfer bias

2BF
1-1-2
Controller hardware ........................ CPU: Power PC750CXe (600 MHz)
System ROM: 8 MB (16 Mbit ×2) ×2
Font ROM: 4 MB (32 Mbit ×1)
Main RAM: 128 MB standard (on-board); expanding up to 512 MB (256 MB ×2) at the
maximum by adding optional expansion memory
Optional expansion RAM (DIMM): 1 slot
168-pin DIMM (64, 128 or 256 MB)
Interface.......................................... Parallel: High-speed (bi-directional), IEEE 1284 Nibble/ECP mode
Optional interface (KUIO-LV) ×1: Network interface card IB-20 (10 Base-TX/100
Base-TX/10 Base-2), IB-21E (10 Base-TX/100 Base-TX), wireless LAN card IB-22
must be installed.
Controller software..........................a) Emulation
PCL6 (PCL5, PCL5e and PCLXL)
KPDL3 (PostScript 3 compatible)
KCGL
b) Fonts:
Bitmap font:
1 Line Printer bitmap font
Outline fonts:
80 PCL fonts
136 KPDL3 fonts:
c) Graphic:
(1) Raster graphic:
75, 100, 150, 200*, 300, 600* dpi
(*200 dpi is supported when the resolution is 600 dpi.)
(2) Vector graphic:
Line, Box, Circle, Arc, Fill pattern etc.
(3) Bar code:
One-dimensional bar code: 45 types
Two o-dimensional bar code: 1 type (PDF-417)
(4) Text:
(5) Others:
d) Connectivity
plug & play, Windows 95/98/ME/NT4.0/2000/XP
SNMP (KM-NET viewer)
Resolution.......................................600 ×600 dpi (multi 4-bit)
Dimensions .....................................Main unit: 699 ×715 ×463 mm/27.52" ×28.15" ×18.23" (W ×D ×H)
Weight.............................................Main unit: 84.3 kg/186.3 lbs (not including toner containers)
Power source.................................. 220 - 240 V AC, 50/60 Hz (European countries), 120 V AC, 60 Hz (U.S.A./Canada)
Power consumption ........................ Maximum: 1450 W (220 - 240 V model), 1350 W (120 V model)
Normal operating: 700 W (220 - 240 V model), 700 W (120 V model)
Ready: 165 W (220 - 240 V model), 165 W (120 V model)
EcoPower: 30 W (220 - 240 V model), 30 W (120 V model)
Current............................................6.5 A (220 - 240 V model), 12 A (120 V model)
Noise............................................... Printing: 53 dB(A), Ready: 39 dB(A)
Options ...........................................Expansion memory (64/128/256 MB 168-pin DIMM),
memory card (Compact Flash),
hard disk unit HD-10 (10 GB),
network interface card IB-20 (10 BASE-T/100BASE-TX/10BASE-2),network interface
card IB-21E (10BASE-T/100BASE-TX), wireless LAN card IB-22 (compatible to
IEEE802.11b),
serial interface board IB-11, (Maximum: 115 kbps),
paper feeder PF-640 (500 sheets [60 to 105 g/m2] ×1 cassette, A3, B4, A4, A5, B5,
ledger, legal, letter, custom),
paper feeder PF-645 (500 sheets [60 to 105 g/m2] ×3 cassettes, A3, B4, A4, A5, B5,
ledger, legal, letter, custom),
paper feeder PF-647 (500 sheets [60 to 105 g/m2] ×1 cassette, 1000 sheets [60 to
105 g/m2] ×1 deck, 1500 sheets [60 to 105 g/m2] ×1 deck, A3, B4, A4, A5, B5, led-
ger, legal, letter, custom),
duplex unit DU-640,
face-up output tray PT-640 (150 sheets),
caster kit CA-33, dehumidifier heater

2BF
1-1-3
1-1-2 Parts names
(1) Printer
Figure 1-1-1
11
10
8
1
2
9
21
20
13
22
18
23
30
29
3
4
12
19
5
6
7
14
16 15
13
24
25
28
27
26
1. Operation panel
2. Front cover
3. Right cover 1
4. Right cover 2
5. MP tray
6. Paper feed unit
7. Transfer unit
8. Waste toner box
9. Toner container cover
10. Black toner container
11. Yellow toner container
12. Cyan toner container
13. Magenta toner container
14. Black main charger unit
15. Yellow main charger unit
16. Cyan main charger unit
17. Magenta main charger unit
18. Paper cassette
19. Eject cover
20. Fuser unit
21. Face-down exit tray
22. Power switch
23. Paper stopper
24. Memory card slot
25. Parallel interface connector
26. Network interface connector
27. Optional interface slot (OPT1/HDD)
28. Optional interface slot (OPT2)
29. Filter
30. Ozone filter cover

2BF
1-1-4
(2) Operation panel
Figure 1-1-2
765
4
1
3
2
810 11 9 13 12 15 14
1. Message display
2. Interface indicator (INTERFACE)
3. Paper size indicator (SIZE)
4. Paper type indicator (TYPE)
5. Ready indicator (READY)
6. Data indicator (DATA)
7. Attention indicator (ATTENTION)
8. Left key(Y)
9. Right key(Z?)
10. Up key(U)
11. Down key(V)
12. Menu key (MENU)
13. Enter key (ENTER)
14. Cancel key (CANCEL)
15. Go key (GO)

2BF
1-1-5
1-1-3 Cross section view
Figure 1-1-3
20
21
10
22 13
14
18 15 16
17 12 7 89 11
4
2
5
6
119
3
Paper path
Paper path
(Optional equipment)
1. Paper cassette
2. Primary paper feed unit
3. MP tray
4. MP tray feed unit
5. Paper feeder feed section
6. Paper feed unit
7. Magenta process unit
8. Cyan process unit
9. Yellow process unit
10. Black process unit
11. Magenta toner container
12. Cyan toner container
13. Yellow toner container
14. Black toner container
15. Magenta main charger unit
16. Cyan main charger unit
17. Yellow main charger unit
18. Black main charger unit
19. Transfer unit
20. Fuser unit
21. Eject unit
22. Face-down exit section

2BF
1-1-6
This page is intentionally left blank.

2BF
1-2-1
1-2 Handling Precautions
1-2-1 Drum (process unit)
Note the following when handling or storing the drum (process unit).
• When removing the drum (process unit), never expose the drum surface to strong direct light.
• Avoid abrupt changes in temperature and humidity.
• Avoid exposure to any substance which is harmful to or may affect the quality of the drum.
• Do not touch the drum surface with any object. Should it be touched by hands or stained with oil, clean it.
Developer (process unit) and toner container
Store the developer (process unit) and toner container in a cool, dark place.
Avoid direct light and high humidity.
1-2-2 Installation environment
1. Temperature: 10 - 32.5 °C/50 - 90.5 °F
2. Humidity: 20 - 80%RH
3. Power supply: 120 V AC (U.S.A./Canada), 220 - 240 V AC (European countries)
4. Power source frequency: 50 Hz ±2%/60 Hz ±2%
5. Installation location
• Avoid direct sunlight or bright lighting. Ensure that the photo-conductor will not be exposed to direct sunlight or other
strong light when removing paper jams.
• Avoid extremes of temperature and humidity, abrupt ambient temperature changes, and hot or cold air directed onto
the machine.
• Avoid dust and vibration.
• Choose a surface capable of supporting the weight of the machine.
• Place the machine on a level surface (maximum allowance inclination: 1°).
• Avoid air-borne substances that may adversely affect the machine or degrade the photo-conductor, such as mercury,
acidic of alkaline vapors, inorganic gasses, NOx, SOx gases and chlorine-based organic solvents.
• Select a room with good ventilation.
6. Allow sufficient access for proper operation and maintenance of the machine.
Machine front: 600 mm/26.6" Machine rear: 250 mm/9.84"
Machine right: 250 mm/9.84" Machine left: 400 mm/15.7"
Machine top: 750 mm/29.5"
Figure 1-2-1 Installation dimensions
a
bc
a: 463 mm/18.23"
b: 699 mm/27.52"
c: 715 mm/28.15"

2BF
1-2-2
This page is intentionally left blank.

2BF
1-3-1
1-3 Installation
1-3-1 Unpacking and installation
(1) Installation procedure
Figure 1-3-1
Unpacking.
Installing the toner containers.
Installing the waste toner box.
Securing the fuser press screws.
Loading paper.
Start
Connecting the cable.
Printing a status page for test.
Completion of the machine installation.
Installing the process units and main
charger units.

2BF
1-3-2
Figure 1-3-2 Unpacking
Unpacking.
6
2
1
10
14
12 13 15
345
7
16
11 11
89
1. Printer
2. Installation Guide, Quick Guide,
Quick Configuration Guide and
two CD-ROM
3. Cyan process unit
4. Magenta process unit
5. Yellow process unit
6. Black process unit
7. Cyan main charger unit
8. Magenta main charger unit
9. Yellow main charger unit
10. Black main charger unit
11. Waste toner box (two)
12. Cyan toner container
13. Magenta toner container
14. Yellow toner container
15. Black toner container
16. Power cord