Kyocera KM-4800w User manual

Printer Driver
for Windows Vista
User’s Manual

1
Regarding this manual
This manual explains how to install Windows Printer Driver and how to use it.
This Printer Driver can be used with Microsoft Windows Vista.

2
Index
1. INSTALLATION METHOD................................................................................ 3
1.1. Install TCP/IP Port......................................................................................................................................................... 3
1.2. Add Printer...................................................................................................................................................................... 6
1.3. About Printer Port........................................................................................................................................................14
1.4. About reinstall of Printer..............................................................................................................................................17
2. SETTING ITEM OF PRINTER DRIVER ....................................................22

3
1. Installation Method
1.1. Install TCP/IP Port
1. Insert Installation Disk in CD-ROM driver.
2. Open “(the optical drive)\Software\PrinterPort\”.
Right-click on “KM4800wTcpMon_xxx.exe” and select “Run as administrator”.
(xxx is the version)
[A program needs your permission to continue] will appear. Click “Continue”.
3. Click “OK”.

4
4. Click “Next”.
5. Click “Install”.

5
6. Please wait while the wizard is installing the components.
7. Click “Finish”.
TCP/IP port installation is completed.

6
1.2. Add Printer
1. Launch “Printers” in Control Panel.
2. Right-click within a blank region and select “Run as administrator” and “Add Printer”.
[Windows needs your permission to continue] will appear. Click “Continue”.

7
3. Click “Add a local printer”.
4. Select “Create a new port”.
Select “KM-4800w TCP/IP Port” in the pull-down menu for port types.
Click “Next”.
If "KM-4800w TCP/IP Port" exists, select "Use an existing port:" and specify the
"KM-4800w TCP/IP Port" from the pull-down menu.

8
5. Enter the KM-4800w’s IP address or host name.
Click “OK”.
6. Click “Have Disk”.

9
7. Click “Browse”.
8. Specify “K48PREN.INF” at “(the optical drive)\Software\PrinterDriver\EN\”
Click “Open”.
English: specify \Software\PrinterDriver\EN\ K48PREN.INF
French: specify \Software\PrinterDriver\FR\ K48PRFR.INF
German: specify \Software\PrinterDriver\DE\ K48PRDE.INF
Italian: specify \Software\PrinterDriver\IT\ K48PRIT.INF
Spanish: specify \Software\PrinterDriver\ES\ K48PRES.INF

10
9. Click “OK”.
10. Click “Next”.

11
11. If KM-4800w Printer Driver is already installed on your system, the following screen
appears.
Select “Replace the current driver” and click “Next”.
12. Printer name can be changed at your option.
Click “Next”.

12
13. Check “Always trust software from “KYOCERA MITA Corporation”.” and click “Install”.
14. Please wait while the wizard is installing the components.

13
15. Select “Do not share this printer” and click “Next”.
16. Click “Finish”.
Installation of printer has been finished.

14
1.3. About Printer Port
Select the printer you have added by right-click, and select “Run as administrator” and
“Properties”.
[Windows needs your permission to continue] will appear. Click “Continue”.

15
Select the “Ports” Tab.
Select “KM-4800w:192.168….Port”, and click “Configure Port”.

16
The following information is indicated.
You do not have to change any of the above settings in usual case.
Change these settings when KM-4800w does not wake up correctly from the Power
Save Mode caused by the network settings.
MAC Address: MAC Address of output printer
Broad Cast Address: An address used to send the data to all PC on the network
Magic Boot Port: Port number to send the data
Timeout: Timeout when no response comes from the output printer
Retry: Number of retry when no response comes from the output printer

17
1.4. About reinstall of Printer
When reinstalling KM-4800wEN to the system, first delete the existing KM-4800wEN
components.
Select a printer to be deleted.
Right-click on it and select “Run as administrator” and “Delete”.
[Windows needs your permission to continue] will appear. Click “Continue”.
Click “Yes”.

18
Right-click within a blank region and select “Run as administrator” and “Server
Properties”.
[Windows needs your permission to continue] will appear. Click “Continue”.

19
Select the “Drivers” Tab.
Select “KM-4800wEN” and click “Remove”.