Kyocera FS C5030N - Color LED Printer Installation and operation manual

Page 1 - 11
Kyocera Classic Universal Printer Driver
Tips, hints, and issues
Before you start using the Kyocera Classic Universal Driver you should study this document
to learn some specific issues of this driver.
Properties
Tab: Extended Settings
After installing the driver you have the choice to set-up the finisher of the print driver.
You can set-up the print driver with the finisher
options you like to use or the user should use
only.
In addition you have the possibility to set-up the
finisher options of the print driver using the ‘Auto
Configuration Feature’. To do so click the button
‘Set-up’. You will see a new Window. For more
information see below.
After auto configuration of the print driver you
have the possibility to deselect finisher options
which are not needed.
‘Watermark’ is an additional selectable feature.
‘Auto Configuration’ ask you for the IP address /
Host name, SNMP community name, and the
SNMP time-out. If all values are correct click
‘OK’. The print driver will query the printer if
possible and set-up the settings of the finisher
tab only.

Page 2 - 11
Properties
Tab: Device Settings
‘Paper Feeder:’ and ‘Duplex Unit (...):’ should
be set-up at installation time (Vista and newer). If
not please make the correct settings here.
‘Printer Memory:’ please does the choice that
fits best to your printer.
Collate: (PCL driver only)
For collating copies of a multiple page
print job there are two possibilities.
Printer (im Drucker (RAM-Disk / HDD))
Using the collate feature you must enable the
RAM disk of the printer or install a HD/MD drive
to your printer. This feature will decrease the size
of the print-job.
Programme (vom Programm)
Some printers do not allow RAM disk or the
usage of a HD/MD disk. In this case you can use
the extended print functions of Windows. Several
programmes support this software collate
feature. This feature will increase the size of the
print-job.
Attention
If you use ‘Separation’ or ‘Staple’ feature there is a limitation using setting ‘Programme’.
‘Collate -> Programme’ sends all copies in one whole print job. In this case the printer cannot
separate each copy. Also the printer will staple the whole print job not each copy.
‘Collate -> Printer’ sends a copy collate command for the print job. In this case the printer
knows where to separate and/or staple each copy.

Page 3 - 11
Job Account:
You can decide whether the user
can/must use ‘Job Accounting’ or not.
OFF
The user can not use Job Accounting.
On
The user can use Job Accounting without any
limitations.
Lock
First the administrator set-up a specific Job
Accounting Number in ‘Printing Preferences…’
using the user account; (‘Job Account: On’).
After setting-up the ‘Job Accounting Number’ the
admin can look this entry; (‘Job Account: Lock’).
The user can not change this number without
having admin rights.
Job Retention:
Similar to ‘Job Account’ the admin can
lock the entries of ‘Job Retention’.
Attention
‘Job Retention’ is only available if a RAM-
or HD/MD-disk is installed / enabled.
Unlock
The user can use Job Retention without any
limitations.
Lock
First the administrator set-up Job Retention in
‘Printing Preferences…’ using the user account;
(‘Job Retention: Unlock’).
After setting-up the ‘Job Retention’ for the user
the admin can look the ‘Job Retention’ tab; (‘Job
Retention: Lock’). The user can not change these
settings without having admin rights.
Halftone Matrix
If the shape of grayscale is too dark you can
change the halftone matrix of the rendering
module.
This feature is valid only for the ‘HP-GL/2’ mode.

Page 4 - 11
Printing Preferences
Tab: Paper/Quality (Colour printers only)
Paper/Quality
If you switch the print driver from Monochrome to
Colour, there is a chance that the printer still
prints b/w instead of colour.
In this case click the button ‘Advanced…’ and do
the settings shown below.
Move to ‘Color Printing Mode:’
(Farbdruckmodus:) and switch the setting to
‘True Color (24bpp)’.
To confirm the setting click ‘OK’.
Window: Advanced…
Graphics Mode: (PCL 5 driver only)
If you have problems getting a correct print-out of
a specific document try to use another setting of
‘Graphics Mode:’ (Grafikmodus:). There are two
choices, ‘HP-GL/2’ or ‘Raster’.
In most cases switching the graphics mode will
help.

Page 5 - 11
Duplex Options (PCL driver only)
With this feature you can control the page order if
you use duplex (Vista and newer)
Off Page order for 4 pages print job is as
follows:
Sheet 1 -> pages 4 / 3 -> pages 2 /1
Reverse page
Page order for 4 pages print job is as
follows:
Sheet 1 -> pages 3 / 4 -> pages 1 /2
No blank page
In some cases an additional blank page
will be printed-out. This setting avoids to
print the additional page, if possible.
Both Both settings, ‘Reverse page’ and ‘No
blank page’, will be active
EcoPrint:
This setting reduces the toner consumption but
also the print quality. This setting is good for draft
print-outs.
Half Speed mode:
Some printers support this feature. This feature
reduces the print speed and the print noise and
increase the print quality.
Halftone matrix: (PCL driver only)
If the shape of grayscale is not smooth you can
change the halftone matrix of the printer.
This feature is valid for new models only.
Job Setting: (KPDL driver only)
With this feature you can force ‘copy collate’ if
the programme does not support ‘copy collate’.
The printer needs to have a RAM-/HD-disk.
Printer Default Printer settings will be used.
Collate Copy collate will be used.
None Standard copy will be used.
Scale to Page Size: (KPDL driver only)
With this feature you can scale your master to
another size for print-out; Letter, A4, and A5.

Page 6 - 11
KyoControl
The Kyocera Classic Universal Driver (PCL) is designed to use with KyoControl. Several
information will be send within the print-job like user name, job name, etc. There are some
points you must take care.
User Name
The user name will be taken from the login name of Windows. To get the valid name you
must open ‘Printing Preferences…’ (Druckeinstellungen…) and exit with ‘OK’ once.
Otherwise the user name will not be send.
There is a script available to do this at login-time. Please ask your dealer for the ‘Kyocera
MultiDriver’ login script.
Job Retention (Auftragsbearbeitung)
You should not use KyoControl and Job Retention together because the print jobs will be
stored centrally on the KyoControl server and should not be stored locally in the printer.
If you have problems using copy collate try following settings:
Tab: Properties
Extended Settings -> RAM disk Mode 1 or 2
Device Settings -> Collate: Printer
Device Settings -> Job Retention: Lock
Limitations
User Name and Job Name are limited to 30 characters.
Attention
There is an issue in Server / Client environment; if you install and configure the driver on a
print-server for sharing, maybe the login-name of the server-administrator will be pushed to
the clients.
To avoid this you must activate ‘JobRetention’-tab and delete the user name from the edit-
box. Do not change anything afterwards; click OK immediately after deleting the user name.
This problem only occurs if you changed any ‘Printing Properties’ on server side.
Attention
If you use this driver in a multi manufactory printer environment please be aware that some
features of this driver uses Kyocera specific commands which will be printed out by our
competitors.
These are the selection of some envelopes sizes like C4, Executive, etc.
And also the selection of some exotic paper sizes like Oficio, 8K, 16K, etc., and custom
paper size.
And the feature of the finishers ‘Jog’.

Page 7 - 11
Overview Extended Settings
Extended Settings
The Finisher options are divided in Extended
Settings, Punch Unit Type, and Staple Unit.
In this section the administrator can decide which
options of the Finisher should be available for the
user by the print driver.
You can add the Punch Unit and/or Staple Unit if
the unit is available.
Also you can decide not to select a Unit, even if
the Unit is available, to avoid the user to use the
features available by the specific Unit.
Job Separator or Internal Finisher
You can add a Job Separator or an Internal
Finisher.
The Internal Finisher also supports stapling. You
can decide if the user can use the Staple Unit or
not.
1000 Sheet Finisher
You can add a 1000 Sheet Finisher and in
addition a Job Separator, if your model supports
this combination.
This Finisher supports stapling. You can decide if
the user can use the Staple Unit or not.
3000 / 4000 Sheet Finisher
You can add a 3000 / 4000 Sheet Finisher and in
addition a Job Separator, if your model supports
this combination.
Also you can add a Mailbox Unit, a Booklet /
Folding Unit, a Punch Unit and a Staple Unit, if
they are available and the user should be able to
use them. If you add a Punch Unit you must
select how much holes the Punch Unit supports; 2
holes, 2/3 holes (America), or 2/4 holes (Europe).

Page 8 - 11
Job Storage
RAM Disk / Hard Disk
RAM Disk Mode 1 models support (e.g.):
FS-1800 / 1900, FS-3800,
FS-C5016 / C5020 / C5025 / C5030
KM-3035 / 4035 / 5035
RAM Disk Mode 2 models support (e.g.):
FS-2020D / 3920DN
FS-C5100DN / C5200DN
HD models support (e.g.):
FS-4020DN / FS-C5300DN
VMB models support (e.g.):
FS-1800 / 1900 / 3800, FS-C5016 / C5020 / C5025 /
C5030
KM-2540 / 3040, KM-3035 / 4035 / 5035, KM-6030 / 8030
KM-C2520 / C3225 / C3232, KM-C2525E / C3225E /
C3232E / C4035E
UserBox models supported (e.g.):
KM-3050 / 4050 / 5050 / KM-2560 / 3060
TASKalfa 250ci / 300ci / 400ci / 500ci
TASKalfa 4500i / 5500i / 6500i / 8000i and newer
B/W or Colour Printer
(Colour models only)
In this section you can select B/W or Colour printing to
allow the user to print documents in colour or not.
If you select Colour Printer you have three choices:
No Colour Mode selected This setting is good for
old colour models.
Colour Mode 1 This setting is valid for following
printer series: FS-C50xx and KM-C2520 / C3225 /
C3232
Colour Mode 2 This setting is valid for following
printer series: FS-C5x00, KM-C2525E / C3225E /
C3232E / C4035E, TASKalfa 250ci / 300ci / 400ci / 500ci,
TASKalfa 4550ci / 5550ci / 7550ci and newer
Watermark (not PCL XL/6)
In this section you can select whether the user can use
the Watermark feature or not. This feature is printer
model independent.

Page 9 - 11
Addendum
Kyocera Classic Universaldriver for PCL 5e/c and KPDL
List of printers which will be supported by the PCL 5e/c and KPDL Classic Universaldriver.
Kyocera Mita FS-1018MFP
Kyocera Mita FS-1020D
Kyocera Mita FS-1050
Kyocera Mita FS-820
Kyocera Mita FS-920
Kyocera Mita FS-C5020N
Kyocera Mita FS-C5030N
Kyocera KM-1820
Kyocera KM-2540
Kyocera KM-2560
Kyocera KM-2810
Kyocera KM-2820
Kyocera KM-3040
Kyocera KM-3050
Kyocera KM-3060
Kyocera KM-4050
Kyocera KM-5050
Kyocera KM-6030
Kyocera KM-8030
Kyocera KM-C2520
Kyocera KM-C2525E
Kyocera KM-C3225
Kyocera KM-C3225E
Kyocera KM-C3232
Kyocera KM-C3232E
Kyocera KM-C4008
Kyocera KM-C4035E
Kyocera FS-1028MFP
Kyocera FS-1030D
Kyocera FS-1030MFP
Kyocera FS-1035MFP
Kyocera FS-1100
Kyocera FS-1118MFP
Kyocera FS-1120D
Kyocera FS-1128MFP
Kyocera FS-1130MFP
Kyocera FS-1135MFP
Kyocera FS-1300D
Kyocera FS-1320D
Kyocera FS-1350DN
Kyocera FS-1370DN
Kyocera FS-2000D
Kyocera FS-2020D
Kyocera FS-3040MFP
Kyocera FS-3040MFP+
Kyocera FS-3140MFP
Kyocera FS-3140MFP+
Kyocera FS-3540MFP
Kyocera FS-3640MFP
Kyocera FS-3900DN
Kyocera FS-3920DN
Kyocera FS-4000DN
Kyocera FS-4020DN
Kyocera FS-6025MFP
Kyocera FS-6030MFP
Kyocera FS-6950DN
Kyocera FS-6970DN
Kyocera FS-9130DN
Kyocera FS-9530DN
Kyocera FS-C2026
Kyocera FS-C2026MFP+
Kyocera FS-C2126
Kyocera FS-C2126MFP+
Kyocera FS-C2526MFP
Kyocera FS-C2626MFP
Kyocera FS-C5015N
Kyocera FS-C5025N
Kyocera FS-C5100DN
Kyocera FS-C5200DN
Kyocera FS-C5300DN
Kyocera FS-C5350DN
Kyocera FS-C5400DN
Kyocera FS-C8020MFP
Kyocera FS-C8025MFP
Kyocera FS-C8100DN
Kyocera FS-C8100DN+
Kyocera FS-C8500DN
TASKalfa 181
TASKalfa 205c
TASKalfa 221
TASKalfa 250ci
TASKalfa 255
TASKalfa 255c
TASKalfa 300ci
TASKalfa 300i
TASKalfa 305
TASKalfa 400ci
TASKalfa 420i
TASKalfa 500ci
TASKalfa 520i
TASKalfa 552ci
TASKalfa 620
TASKalfa 820
TASKalfa 3050
TASKalfa 3500
TASKalfa 3550
TASKalfa 4500
TASKalfa 4550
TASKalfa 5500
TASKalfa 5550
TASKalfa 6500
TASKalfa 6550
TASKalfa 7550
TASKalfa 8000

Page 10 - 11
Kyocera Classic Universaldriver for PCL 6 / XL
List of printers which will be supported by the PCL 5e/c and KPDL Classic Universaldriver.
Kyocera FS-1028MFP
Kyocera FS-1030MFP
Kyocera FS-1035MFP
Kyocera FS-1118MFP
Kyocera FS-1120D
Kyocera FS-1128MFP
Kyocera FS-1130MFP
Kyocera FS-1135MFP
Kyocera FS-1320D
Kyocera FS-1350DN
Kyocera FS-1370DN
Kyocera FS-2000D
Kyocera FS-2020D
Kyocera FS-3040MFP
Kyocera FS-3040MFP+
Kyocera FS-3140MFP
Kyocera FS-3140MFP+
Kyocera FS-3540MFP
Kyocera FS-3640MFP
Kyocera FS-3900DN
Kyocera FS-3920DN
Kyocera FS-4000DN
Kyocera FS-4020DN
Kyocera FS-6025MFP
Kyocera FS-6030MFP
Kyocera FS-6950DN
Kyocera FS-6970DN
Kyocera FS-9130DN
Kyocera FS-9530DN
Kyocera FS-C2026MFP+
Kyocera FS-C2126MFP+
Kyocera FS-C2526MFP
Kyocera FS-C2626MFP
Kyocera FS-C5100DN
Kyocera FS-C5200DN
Kyocera FS-C5300DN
Kyocera FS-C5350DN
Kyocera FS-C5400DN
Kyocera FS-C8020MFP
Kyocera FS-C8025MFP
TASKalfa 181
TASKalfa 205c
TASKalfa 221
TASKalfa 250ci
TASKalfa 255
TASKalfa 255c
TASKalfa 300ci
TASKalfa 300i
TASKalfa 305
TASKalfa 400ci
TASKalfa 420i
TASKalfa 500ci
TASKalfa 520i
TASKalfa 552ci
TASKalfa 620
TASKalfa 820
TASKalfa 3050
TASKalfa 3500
TASKalfa 3550
TASKalfa 4500
TASKalfa 4550
TASKalfa 5500
TASKalfa 5550
TASKalfa 6500
TASKalfa 6550
TASKalfa 7550
TASKalfa 8000
Following printer models will NOT be supported by the Kyocera Classic Universaldriver:
Kyocera 1020MFP (+)
TASKalfa 550c
TASKalfa 650c
TASKalfa 750c