Kyosho Manoi PF01 User manual

安全のための
注意事項
付属製品に ついて
組み立て
ソフトウェア の設定
MANOI
での
遊び方
オプションパー ツの取り付け
故障かなと 思ったら
ユーザー相談 室のご案内
用語集
パーツ販売
リスト
展開図
3
This product is Assembling Kit. And, it could happen that product can not perform fully if
assembling or operating way is not correct. First‑time builders should seek the advise of
experienced robot user before beginning assembly and if they do not fully understand any
part of the construction.
Required Additional
Some eqipments and tools which are not included in this product are required to assemble
and operate this product. Please, prepare before starting.
○Personal Computor
・The one which can operate Microsoft Windows 2000 or Windows XP （*1）
・The one which has more than 1port of USB Port （*2）
・The one which has CD‑ROM drive
*1） This is not W indows Vista-compliant
*2） B asically use US B port of the PC itself
○Tools
・KYOSHO Ratchet Cross Slot Screwdriver Set （MANOI） ［No.HRP009］
This set has Rachet system to push and tighten screw.It also including 2 type of bits
of #0 and #1.
・Cross Slot Screwdriver（#2）
・Double Faced Tape (thick one) This will be used for fixing Radio Controlled Unit
About Screw Drivers
#0 …
…
…
…
…
…
…
…
Instruction
#1 …
…
…
…
#2 …
*
「#●」means standardized size of screwdriver. It is indicated at handle of screwdriver.
It will be reference for purchasing screwdriver.
Cross Slot Screws are used for fixing parts of this product. And it is necessary
to choose right size of the driver for each size of screw‑head. It is recommended to
use KYOSHO Ratchet Cross Slot Screwdriver Set (MANOI)[No.HRP012]. if incorrect size
driveris used for wrong screw, it will mess screw‑head. Be carefull for this.
M2x8 pan‑head Tapping Sfcrew
M2x5 Pan‑head Tapping Screw
M2x6 Pan‑head Machine Screw
M2x5 Countersank Tapping Screw
M2x8 Countersank Tapping Screw
M2x10 Countersank Tapping Screw
M2x20 countersank Tapping Screw
M2x16 countersank Tapping Screw
M2.6x8 Pan‑head Tapping Screw
M2.6x10 Pan‑head Tapping Screw
M2.6x14 Pan‑head Tapping Screw
M2.6x10 Countersank Tapping Screw
M3x8 Bind Tapping Screw

4
Tighten Screws
★
Tapping Screw is type of screw which is making screw thread inside of Plastic material
as it is tightened. Therefore, when start thighten the screw it gets hard feeling. Push Tapping
screw down to Screw hole to tighten.
Do not use electric screwdriver for Tapping Screw.
○
① Press screw driver to screw
② Turn by force of fingertip
①
②
Too much force if hold by palm
Screw which is called Tapping Screw is used for this product to fix plastic material part.
This screw is special type of screw, so read below points carefully.
How to hold Screw Driver(example)
Make sure Tapping Screw is perpendicular to screw hole as tighten. If not, it may cause damage on
Parts.
If it is found that Screw is not perpendicular to screw hole, lose screw and remove from screw hole.
Then, make sure it is perpendicular and try again.
When feel very hard to thighten, check if Screw is perpendicular or not.
Tighten the screw until thread of Tapping Screw or head of screw of Pan‑Head Screw get into inside
of Plastic Parts. Thread is inside of parts and get hard feeling of tighten, it is enough.
Too thighten will cause mess of thread which is made inside of Parts. If mess thread,
that screw hole will not be usefull to fix parts and need replacement parts, Especially
Male can cause mess of thread by too much power for tighten. Be carefull of this,
If tigthened screw is needed to be remoeved and tightened again, it is not necesary to
push screw down to screw hole. Just make sure Screw is perpendicular to screw hole and thighten
until enough.
When fix a parts by several screws, all of screw for fixing should not be tightened completely,
stop tighten at 2/3, then tighten all of them completely. Order of tighten screws is
2nd screw which is tigten completely should be the farest from 1st one.

安全のための
注意事項
付属製品に ついて
組み立て
ソフトウェア の設定
MANOI
での
遊び方
オプションパー ツの取り付け
故障かなと 思ったら
ユーザー相談 室のご案内
用語集
パーツ販売
リスト
展開図
5
Safety Precautions ………………………………………………………………7
Component Parts …………………………………………………………… 7
Charger and Li‑Po Battery ……………… 8
Li‑Po Battry ………………………………………………… 9
Accompanying Items
…………………………………………………………… 11
Actuator KRS‑4024SHV ………………………………………… 11
Control Board RCB‑3HV V er1.03 ……………………………… 11
Gyro‑Sensor KRG‑3 ………………………………………………… 11
Charger for Li‑Po Battery ［No. HRCH100］ ………………………… 12
Li‑Po Battery［No.HRBA100］ （for 1sell) ………………… 12
Icon Indication in assembling instruction ……………………… 12
Parts List ………………………………………………………………… 13
Parts Views…………………………………………………………………… 17
Assembling
……………………………………………………………………… 20
Operation 1:Preparation for Assembling …………………………… 20
Operation 2:Set Neutral Positn of Servo Motor(Pack2,11,12)……… 29
Operation 3:Assembling Right Arm (Pack3) …………………………… 43
Operation 3:Assembling Left Arm (Pack4) …………………………… 56
Operation 3:Assembling Right Leg (Pack5) …………………………… 69
Operation 3:Assembling Left Leg (Pack6) …………………………… 85
Operation 3:Assembling Head (Pack7)………………………………… 101
Operation 3:Assembling Body (Pack8)………………………………… 108
Setting Software …………………………………………………………… 119
Operation S1: Preparation for Setting ……………………… 119
Operation S2: Reverse Setting of Servo motor ………………… 123
Operation S3: Setting of Home Position ………………………… 127
Operation S4: Setting of Gyro‑Sensor …………………………… 137
Operation S3: Registration of Sample Motion …………………… 143
How to play MOANI …………………………………………………………… 147
Part 1: Operate by Wired Control …………………………………… 147
Part 2: Move by Automatic …………………………………………… 150
Part 3: Creat Motions ………………………………… 157
Creat by setting numeric number on HTH3 …………………… 159
Creat by moving Arms and Legs(Teaching) ………… 169
CONTENT

6
Attaching Option Parts ………………………………………………… 178
OP01：Control by Radio Controlled system
（Attaching Radio Controlled system） …………………………… 178
Trouble Shooting ……………………………………………………… 197
Cutomer Service Information
…………………………………………… 201
Lexicon
………………………………………………………………………… 202
Sales Parts List ……………………………………………………………… 203
MANOIT M P F01 Exploded View …………………………………………… 206

安全のための 注意事項
付属製品に ついて
組み立て
ソフトウェア の設定
MANOI
での
遊び方
オプションパー ツの取り付け
故障かなと 思ったら
ユーザー相談 室のご案内
用語集
パーツ販売 リスト
展開図
7
Safety Precautions
Componet Parts
★Make sure that chirderen are not around this product when operation/using.
By falling over or unexpected movement,it could cause accidient or injury.
★Keep Chirdren away from small parts.
Some parts are sharp to cause injury and small parts can be swallowed by accident
or mistake.
、
★Do not disassemble or modify Servo Motor and PC board without any instruction
Servo Motor and PC Board are precision electronic part, so disassemble or modify
without any instruction may cause short circuit or fire. For failure is found, contact
The shop where you purchased.
★Do not get product wetting or use in high‑humidity area or dew condensation area
Precision electronic part are used for component parts for this product, so humidity or
liquid will cause damage or failure. if it gets wetting, contact the shop where you
purchased.
★Do not let conductive impurities touch PC Board
Terminals of PC Board etc are not covered, so conductive impurities(Metal or liquid etc)
has danger to cause short circuit easily. Short circuit has possiblity to cause failure or
fire on battery or wiring.
Danger
Warning
Caution
This product is "Assembling Kit", therefor, it could be called upon to take
personal responsibility for using way/result. Use this product with fully
understanding on this point.
This insturuction shows Sign indication for preventing damage on user,other
peope, or assets as follows,
This sign indicates assumable danger which may cause death or serious injury can
be happened.
This sign indicates assumable possibility which may cause death or serious injury
can be happened.
This sign indicates assumable possibility which may cause injury or damage can
be happened.
Warning

8
★Bring this product out from Japan may required legal process for some country or area.
Must check on thsi matter.
★Direct Supoort from Kyosho Corporation is only for Japan market. When Customer Support Service
is necessary,contact the shop where you purchased if the user is not in Japan.
★Do not operate at treacherous place
It will cause falling over by off balance or cause damage or failure by dropping. It also could
cause injury to someone by falling.dropping of product.
★Hold connector ot plug part to pull cable out unless there is any special instruction
Holding cable parts to pull out may cause shock or fire because of breaking of wire
or shirt circuit.
Charger and Li‑Po Battery
This product is using Li‑Po Battery for keeping stable high output power. Li‑Po Battery has
great danger to cause fire or injury if operation is not correct way.
・Use genuine Li‑PO Battery Charger(No.HRCH100) and genuine Li‑Po Battery(No.HRBA100) for
charging and use only for MANOI PF01(No.HR100).If items except genuine items or specified
genuine items are used, it will be out of gurantee and recycling.
●Disposal of damaged/distortional Li‑Po Battery
damaged/distortional Li‑Po Battery is very dangerous to cause fire or burst. Stop using immidiately
and put into salt water a whole night, then insulate battery terminals by tape and bring to the
shopwhere you purchased.
●Charger and Li‑Po Battery
・ Do not disassemble or modify charger and Li‑Po battery. It will cause leak, heat, fire or burst,
and it will be out of gurantee and recycling.
・ If following matters happen, stop using immidiately.
１）Smoking
２）Find unnatural smell or sound
３）Water or extraneous material is inside of battery
４）Damage on battery case
・ Prepare a bucket of water or asphyxiator in case fire.
・ Keep dust, sand away from ferminal part of battery.
・ Do not use near combustible material or plastic material which can be deformed by heat
・ Do not get a wetting
・ If charging is not completed even 80mins is over, and Battery Pack gets heat or is deformed,
stop using immidiately and put into salt water a whole night, then insulate battery terminals
by tape and bring to the shop where you purchased.
Caution

安全のための
注意事項
付属製品に ついて
組み立て
ソフトウェア の設定
MANOI
での
遊び方
オプションパー ツの取り付け
故障かなと 思ったら
ユーザー相談 室のご案内
用語集
パーツ販売
リスト
展開図
9
●Charger
・Charging by no‑sole use AC Quick charger is dangerous.
・Do not connect power code, AC Adaptor, each terminals of charger by incorrect way.
・Keep eye on chrarger and battery during charging and do charge at place of no damage
even if fire or burst happens. Do not charge near combustible objects.
・Do not charge battery or store battery at high‑temperature place such as locations which
receive direct sunlight, or inside of car under the scorching sun.
・Use only for charging.
・Do not leave the charger during charging.
・Disconnect cable from AC Power Point when not using charger.
・Check plug and keep clean regularly.
L i-P o Battery
・When Li‑PO Battery(including Battery case) gets damaged/deformed, stop using immidiately
and put into salt water a whole night, then insulate battery terminals by tape and bring to
the shop where you purchased. If keep using damaged/deformed battery, it is very dangerous to
cause fire or brust.
・ Do not cause short circuit with +terminal and ‑terminal by metal material etc. Short circuit
by both terminal will make the battery bulge out and very dangerous for fire/brust. In case
shory circuit happens, it could shorten life of battery.
・Li‑Po battery can be bulged when it is used by incorrect way. When it starts bulging out,
pull power plug from Power Point and stop charging by manually. Keep charging with bulging
is very dangerous to cause fire/brust.
Li‑Po battery which once started bulging out may be possible to keep bulging even though
stop charging. In that case, move it to safe place such as outside and put into salt water
a whole night, then insulate battery terminals by tape and bring to the shop where you
purchased.
・Keep Li‑Po battery away from children and pets.
・When not using Li‑Po battery, store it without charging.
Danger
Warning
Caution
Warning

10
・Li‑Po battery right after used is very hot. Be careful for handling.
・At Cold Place as below 10℃ will decreace performance of Li‑Po battery and opperation time
will be shorter.
・Li‑Po battery does not have Memory Effect, so it will not cause problem of voltage reduction
even if top off charging without full‑discharge.
・Keep Li‑Po battery at low‑humidity place and charging battery in circumstance of 10〜30℃ can
help to make battery life longer.
Any result which is caused by incorrect way as not following instruction will be out of
gurantee.
Disclaimer
Caution
From judging from the nature of the product, we can not have responsibility on result
around user by using this product. Our limitation of gurantee is replacing the product.
Use this product under user's responsibility.
Specifications are subject to changed without prior notice.

安全のための
注意事項
付属製品に ついて
組み立て
ソフトウェア の設定
MANOI
での
遊び方
オプションパー ツの取り付け
故障かなと 思ったら
ユーザー相談 室のご案内
用語集
パーツ販売
リスト
展開図
11
Actuator K R S -4024S HV
Control Board R C B -3HV Ver1.03
Gyro‑Sensor K R G-3
沙堺婚咋詐策
Included Items
Outside Demension: 43 x 32 x 32.5(mm)
Operationg Voltage: 912V
Torque:10.5kg/cm*
Speed:0.17sec/60*
Maximum Operating Angle:about 260degree
Plastic Gear + Metal gear
*as use with NiCd 9cell
KO Propo's Robot Actutor KRS‑4024SHV is tuned
for MANOI. maximum operating angle:260degree
KO Propo's 24axis controll PC Board. Exsisting PWM signal and
Servo Controll by Serial signel is possible. Sensors such as gyroscopic
can be connect to analog input Port.
Outside Demension: 35 x 45 x 14.5(mm)
Weight:12g
Operationg Voltage: 912V
Output Port: 24
Input Port: 5(annalog3, serial 1+1)
Outside Demension: 22.5 x 12.5 x 7.8(mm)
Weight:1.8g
Operationg Voltage: 35V
range of detectiont: ±300(deg./sec/)
KO Propo's single axis Gyro‑Sensor. It is very simple system as
Output gyro‑elemental device by electrical pressure.
Input Terminal which can monitor analog electrical pressure.

12
C harger for Li-P o B attery
［No.HR C H100］
L i-P o Battery ［No.HR B A100］（For 1c ell ）
Icon Indication in Assembling Instruction
In the assembling Instructions, Icons indicate point of hint or notice. Meaning of each Icons
are as follows.
Icons
……… Be careful for too tighten (see page 4)
… Check view for referece of direction of assembing parts
……… point that Cables may be cliped by parts. Be careful
……… Point with very careful
……… Order of assembling
……… Hint for assembling
Outside Demension: 180 x 140 x 41(mm)
Weight: approximately 300g
Charging Time: approximately 80mins(approximately 1C/Separate charging each cell)
Charging method : Constant Current Method
Outside case material: ABS(flame resisting grade)
Outside Demension: 88 x 37.6 x 11.6(mm)
Weight: approximately 45g
Voltage: 2.5V(min)/3.7V(typ)/4.2V(max)
Capacity: 1250mAh
Chargable current: 1C
Dis‑chargable current: 10C
Protecting circuit method: thermistor(monitoring tempurature, current, and voltage
by dedicated communication circuit inside as discharging)
Outside case material: ABS
①
⇔

安全のための 注意事項
付属製品に ついて
組み立て
ソフトウェア の設定
MANOI
での
遊び方
オプションパー ツの取り付け
故障かなと 思ったら
ユーザー相談 室のご案内
用語集
パーツ販売 リスト
展開図
13
Parts List
Item Name Necessary Numbers Key No. Pakcking No.
Serial USB Adaptor 195Pack 1
Manual,Software & Sample Motion(CD) 194
Extension cable(for Serial USB) 1 112
Pack 2
Li-P o Saver Cover 169
Controll Board Cover 170
Front Body Flame 166
Back Body Flame 164
Battery Hatch 165
Connector Cover 168
Servo Lead 90mm （Black） 2 113
100mm 277
140mm 2 114
150mm 179
180mm 280
210mm 2 115
240mm 2 116
250mm 2 117
340mm 2 118
360mm 2 119
M2.6 ×14 pan‑head Tapping Screw 4
M2 ×8countersunk Tapping Screw 4
M2 ×8pan‑head Tapping Screw 6
Servo C H Label 175
Insulating Tape 1 120
Shoulder Base 113
Pack 3
Arm Base 110
Front Arm Guide 111
Rear Arm Guide 112
Front Arm Flame 15
Rear Arm Flame 16
Arm Side Cover 17
Arm Cover 214
Arm Screw Cover 215
Arm Joint 22
Front Arm Plate 13
Rear Arm Plate 14
Fronf Hand (Right)） 18
Rear Hand (Right) 19
Hand Cap 216
Knuckle (right) 117
M2 ×5pan‑head Tapping Screw 8
M2 ×6pan‑head Machine Screw 4
M2 ×10 pan‑head Tapping Screw 16
M2 ×16 pan‑head Machine Screw 8
M2 ×20 pan‑head Machine Screw 4
M2 Nut 2types 4
M3 ×8Bind Tapping Screw 3
Servo Lead
Servo Lead
Servo Lead
Servo Lead
Servo Lead
Servo Lead
Servo Lead
Servo Lead
Servo Lead
（Black）
（Black）
（Black）
（Black）
（Black）
（Black）
（Black）
（Black）
（Black）

14
Item Name Necessary Numbers
M2.6 ×10 4
Pack 3
M2.6 ×10 3
Low Height Servo Horn 273
Shoulder base 113
Pack 4
Arm Base 110
Front Arm Guide 111
Rear Arm Guide 112
Front Arm Flame 15
Rear Arm Flame 16
Arm Side Cover 17
Arm Cover 214
Arm Screw Cover 215
Arm Joint 22
Front Arm Plate 13
Rear Arm Plate 14
Front Hand (Left) 118
Rear Hand (Left) 119
Hand Cap 216
Knuckle (Left) 120
M2 ×5 8
M2 ×6 4
M2 ×10 16
M2 ×16 8
M2 ×20 4
M2 Nut (2types) 4
M3 ×8 3
M2.6 ×10 4
M2.6 ×10 3
Low height Servo Horn 273
Side Ankle 122
Pack 5
Thigh Flame 132
Front Hip Flame (Right) 136
Rear Hip Flame(Right) 139
Inside Hip Flame 137
Outside Hip Flame 138
Side Hip Cover 140
Front Thigh Cover (Right) 134
Rear Thigh Cover(Right) 135
Outside Knee (Right) 129
Knee Cover (Right) 130
Inside Knee (Right) 133
Knee Stay 131
Front Ankle (Right) 123
Middle Ankle 121
Rear Ankle 124
Rear Ankle Joint (Right) 125
Front Ankle Joint (Right) 126
Shoe (right) 127
Sole (Right) 128
Ankle Cap 141
Key No. Pakcking No.
countersunk Tapping Screw
pan‑head Tapping Screw
countersunk Tapping Screw
countersunk Tapping Screw
countersunk Tapping Screw
pan‑head Tapping Screw
pan‑head Machine Screw
countersunk Machine Screw
countersunk Machine Screw
bind Tapping Screw

安全のための
注意事項
付属製品に ついて
組み立て
ソフトウェア の設定
MANOI
での
遊び方
オプションパー ツの取り付け
故障かなと 思ったら
ユーザー相談 室のご案内
用語集
パーツ販売 リスト
展開図
15
Item Name Necessary Numbers Key No. Pakcking No.
M2 ×5countersunk Tapping Screw 14
Pack 5
M2 ×5pan‑head Tapping Screw 12
M2 ×8pan‑head Tapping Screw 10
M2 ×10 countersunk Tapping Screw 16
M2 ×16 countersunk Machine Screw 18
M3 ×8bind Tapping Screw 4
M2.6 ×8pan‑head Tapping Screw 2
M2.6 ×10 countersunk Tapping Screw 8
Low Hight Servo Horn 573
Side Ankle 122
Pack 6
Thigh Flame 132
Front Hip Flame (Left) 152
Rear Hip Flame (Left) 153
Inside Hip Flame 137
Outside Hip Flame 138
Side Hip Cover 140
Front Thigh Cover (Left) 150
Rear Thigh Cover (Left) 151
Outside Knee (Left) 147
Knee Cover (Left) 148
Inside Knee (Left) 149
Knee Stay 131
Front Ankle (Left) 142
Middle Ankle 121
Rear Ankle 124
Rear Ankle Joint (Left) 143
Front Ankle Joint (Left) 144
Shoe (Left) 145
Sole (Left) 146
Ankle Cap 141
M2 ×5countersunk Tapping Screw 14
M2 ×5pan‑head Tapping Screw 12
M2 ×8pan‑head Tapping Screw 10
M2 ×10 countersunk Tapping Screw 16
M2 ×16 countersunk Machine Screw 18
M3 ×8bind Tapping Screw 4
M2.6 ×8pan‑head Tapping Screw 2
M2.6 ×10 countersunk Tapping Screw 8
Low Height Servo Horn 573
Neck Support 154
Pack 7
Face 160
Back Head 161
Neck Base 155
Back Head Cap 163
Head Base 156
Visor 162
Eye Base 257
Eye 258
Pupil 259
M2 ×8countersunk Tapping Screw 4

16
Item Name Necessary Numbers Key No. Pakcking No.
M2 ×20 countersunk Machine Screw 2
Pack 7
M3 ×8bind Tapping Screw 1
M2.6 ×10 pan‑head Tapping Screw 6
Low Height Servo Horn 173
Front Cowl 172
Pack 8
Back Cowl 171
M2 ×5countersunk Tapping Screw 8
M3 ×8pan‑head Tapping Screw 2
M2.6 ×8pan‑head Tapping Screw 4
PF Logo Stiker 196
Pack 9
Silicon Grease 174
Gyro‑Sensor Unit (K R G-3) 286
M2.6 ×14 pan‑head Tapping Screw(for spare) 2
Pack10
M2.6 ×10 pan‑head Tapping Screw(for spare) 3
M2.6 ×8pan‑head Tapping Screw(for spare) 2
M2.6 ×10 countersunk Tapping Screw(for spare) 6
M2 Nut 2types(for spare) 2
M2 ×8pan‑head Tapping Screw(for spare) 6
M2 ×5pan‑head Tapping Screw）(for spare) 4
M2 ×6pan‑head Machine Screw(for spare) 4
M2 ×10 countersunk Tapping Screw(for spare) 14
M2 ×20 countersunk Machine Screw(for spare) 2
M2 ×16 countersunk Machine Screw(for spare) 10
M2 ×5countersunk Tapping Screw(for spare) 10
M2 ×8countersunk Tapping Screw(for spare) 2
M3 ×8bind Tapping Screw(for spare) 3
Servo Motor (KR S -4024S HV) 17 1 Pack11
Li-P o Savor 188
Pack12
Switch 190
Control Board (R C B -3) 185
Battery Connector Unit 187
Connector Label 1 111
Side Leg Chekcing Tool 1 121
Pack13
Rear Leg Checking Tool 1 122
Under Leg Checking Tool 1 123
Upper Arm Checking Tool 1 124
Bottom Arm Checking Tool 1 125
Li-P o Battery（ 1250mAh）393
Li-P o AC Chager for MANOI 191
AC Adaptor 192
Instruction Manual (Booklet) 1
Greeting Letter from Suzuki Chairman 1
Full Size Drawing Sheet for Screws 1
Full Size Drawing Sheet for Servo Leads 1
MANOI Advisory 1
User's Post Card 1
countersunk Tapping Screw

安全のための 注意事項
付属製品に ついて
組み立て
ソフトウェア の設定
MANOI
での
遊び方
オプションパー ツの取り付け
故障かなと 思ったら
ユーザー相談 室のご案内
用語集
パーツ販売 リスト
展開図
17
Parts Views
Arms
［1］Servo Motor
Low Height Servo Horn
［2］Arm Joint
［16］Hand Cap
［15］Arm Screw Cover
［12］Rear Arm Guide ［11］Front Arm Guide ［14］Arm Cover
［13］Shoulder Base ［10］Arm Base
［4］Rear Arm Plate ［3］Front Arm Plate ［5］Front Arm Flame
［7］Front Side Cover
［6］Rear Arm Flame
［8］Front Hand(Right)
［9］Rear Hand(Right)
［17］Knuckle(Right)
［18］Front Hand(Left)
［19］Rear Hand(Left)
［20］Knuckle(Left)
［73］
※Arm Parts without mentioned of (Right) or (Left) is common parts for
Right and Left.
RIGHT LEFT

18
Right Leg
Left Leg
［21］
［24］Rear Ankle
［40］Side Hip Cover
［36］
Front Hip Flame
(Right)
［42］
［48］
［52］ ［53］
［46］
［47］
Outside Knee
(Left)
［49］
［44］ ［43］
［38］ ［37］ ［39］ ［41］
Ankle Cap
［28］
Sole(Right)
［32］Thigh Flame ［33］
Inside Knee
(Right)
［27］Shoe(Right)
［35］
［51］
［34］
Front Thigh Cover
(Right)
［50］
［45］
［30］Knee Cover(Right) ［31 ］Knee Stay［29］Outside Knee
(Right)
［22］Side Ankle ［23 ］Front Ankle
(Right)
［26］
Front Ankle
Joint(Right)
［25］Rear Ankle
Joint(Right)
※Leg Parts without mentioned of (Left)or (Right) is
common parts for Left and Right.
Middle Ankle
Rear Thigh Cover
(Right)
Outside Hip Flame Inside Hip Flame Rear Hip Flame
(Right)
Front Ankle
(Left)
Front Ankle
Joint(Left)
Rear Ankle
Joint(Left)
Shoe(Left)
Knee Cover(Left)Inside Knee
(Left)
Front Thigh Cover
(Left)
Rear Thigh Cover
(Left)
Sole(Left)
Rear Hip Flame
(Left)
Front Hip Flame
(Left)

安全のための 注意事項
付属製品に ついて
組み立て
ソフトウェア の設定
MANOI
での
遊び方
オプションパー ツの取り付け
故障かなと 思ったら
ユーザー相談 室のご案内
用語集
パーツ販売 リスト
展開図
19
Head
Body
［56］Head base
［54］Neck Support
［62］Visor ［63］Back Head Cap
［57］Eye Base
［58］Eye
［59］Pupil
［55］Neck base
［60］Face
［72］Front Cowl
［90］Switch
［70］Control Board Cover
［85］Control Board(RCB‑3)
［88］Li‑Po Savor
［74］Silicon Grease
［87］Battery Connector Unit
［86］Gyro‑Sensor Unit（KRG‑3）
［69］Li‑Po Savor Cover
［65］Battery Hatch
［68］
Connector Cover
［66］
Front Body Flame
［64］
［71］Back Cowl
［61］Back Head
Back Body Flame

20
アイコン解説
注意 ポイント 締め込み注意 方向注意
<{@ 組み立て順番
^ 挟み込み注意
Assembling
工程 01 Preparation of Assembling
New Prats for this step
［91］Charger for Li‑Po Battery x 1
［92］AC Adaptor for the charger
Power Code x 1
［93］Li‑Po Battery x 3
［95］Serial USB Adaptor x 1
accessory CD‑ROM x 1
1-1 Charging Battery
T o c harge L i- P o battery, us e c ombina tion of c harger for L i- P o B attery
[No.HR C H100] and L i-P o B attery[No.HR B A100]. Als o us e only AC Adaptor
[No.HR C H101] for the c ha rger.
Charging single Li‑Po battery pack is okay, but use all of 3sells of Li‑Po battery
to operation of MANOI PF01. Also, do not use Li‑Po battery packs as only one pack
is full‑charged and others are not full‑charged. Li‑Po Battery can accept top off
charging, so it is not necessary to do dis‑charging,
Please, read instrcution manual of Charger for Li‑Po Battery{No.HRCH100] also.
Charging Method
① Connect Power Code to AC Adaptor.