La Crosse Technology 515-1419 User manual

TEXTURIZED ATOMIC
DIGITAL WALL CLOCK
MODELS: 5151419
DC: 092418
FIND MANUALS, FAQS, AND MORE UNDER THE
SUPPORT TAB HERE: bit.ly/515-1419

TABLE OF CONTENTS
Page | 2
3. Power Up
3. Custom Date Display
4. Settings Menu
5. WWVB Atomic Time Signal
5. Alarm
6. Low Battery Indicator
6. Specifications
6. We’re Here to Help!
6. Join the Conversation
6. Care and Maintenance
7. Warranty Info
7. FCC Statement

POWER UP
1. Insert 3-AA batteries into your Atomic Clock.
• Press the MODE button to display Counting Seconds or your Indoor Temperature.
• Press the MODE button again to switch back.
Counting Seconds
Indoor Temperature
AA
AA
AA
CUSTOM DATE DISPLAY
Page | 3

Press one button at a time while setting your clock.
1. Hold the MODE button to enter the Settings Menu.
2. Use the + or - button to adjust and MODE to confirm.
Settings Menu order:
• Beep ON/OFF
• WWVB ON/OFF
• Time Zone
• DST ON/OFF
• 12/24 Hour Time
• Hour
• Minutes
• Year
• Month
• Date
• Fahrenheit/Celsius
Note: Weekday sets automatically when Year, Month and Date are set.
SETTINGS MENU
BEEP ON/OFF TIME ZONEWWVB ON/OFF
DATE FAHREHNHEIT/CELSIUS
MINUTES MONTHYEAR
DST ON/OFF HOUR12/24 HOUR FORMAT
Page | 4

WWVB ATOMIC TIME SIGNAL
• Hold the PLUS (+) button to start or stop a manual search for the WWVB Atomic Time Signal.
• The WWVB Tower Icon will flash when searching and be solid when signal is received.
• For information about WWVB Atomic Time visit: bit.ly/AtomicTime
ALARM
Set Alarm:
1. Hold the ALARM button to enter Alarm Settings.
2. Use the + or - button to adjust values.
3. Press the ALARM button to confirm and move to next item.
Silence a sounding alarm: Press any button except SNOOZE to
silence alarm for 24 hours.
Activate/Deactivate Alarm:
• Press the ALARM button once to view alarm time.
• While viewing alarm time, press the ALARM button to
deactivate or activate the alarm.
• The Bell Icon will show when alarm is active.
Snooze:
• When the alarm sounds, press the SNOOZE button to silence
the alarm for 10 minutes. Zz will show next to the Bell Icon.
Note: The alarm will sound with increasing frequency for two minutes, then shut off completely if
not deactivated.
Alarm and Snooze Alarm and Snooze Inactive
Page | 5

• When battery indicator shows replace batteries in your clock.
Indoor Temperature Range: 32°F to 122°F (0°C to 50°C)
Power: 3-AA batteries not included
Battery Life: over 12 months
Dimensions: 15.42” x 7.33” x 1.14”(39.16cm x 18.62cm x 2.90cm)
LOW BATTERY INDICATOR
SPECIFICATIONS
If you require additional support, call our friendly customer support team based out of La Crosse,
Wisconsin.
Phone: [phone]
Or fill out our online support request form here: bit.ly/contact_techsupport
Our knowledgeable customer support team is available:
Monday-Friday, 8am-6pm CST.
JOIN THE CONVERSATION
Ask questions, watch detailed setup videos, and provide feedback on our social media outlets!
WE’RE HERE TO HELP!
CARE & MAINTENANCE
• Do not mix old and new batteries.
• Do not mix Alkaline, Standard, Lithium, or Rechargeable batteries.
• Always purchase the correct size and grade of battery most suitable for intended use.
• Replace all batteries of a set at the same time.
• Clean the battery contacts and also those of the device prior to battery installation.
• Ensure the batteries are installed with correct polarity (+ and -).
• Remove batteries from equipment which is not to be used for an extended period of time.
• Promptly remove expired batteries.
Page | 6

WARRANTY
FCC STATEMENT
La Crosse Technology, Ltd. provides a 1-year limited time warranty (from date of purchase) on this
product relating to manufacturing defects in materials & workmanship.
For Full Warranty Details, Visit: www.lacrossetechnology.com/support
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device must not be co-located or operating in conjunction with any other antenna or transmitter.
Operation is subject to the following two conditions:
(1 ) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Caution!
The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user authority to operate the
equipment.
All rights reserved. This manual may not be reproduced in any form, even in part, or duplicated or
processed using electronic, mechanical or chemical process without the written permission of the
publisher.
This booklet may contain errors or misprints. The information it contains is regularly checked and
corrections are included in subsequent editions. We disclaim any responsibility for any technical error or
printing error, or their consequences.
All trademarks and patents are recognized.
WARNING: This product can expose you to chemicals including styrene, which is known to the State
of California to cause cancer. For more information go to: www.P65Warnings.ca.gov
Page | 7