La Crosse Technology WT-8005U User manual

WT-8005U www.lacrossetechnology.com/support Page | 1
Model: WT-8005U
Instruction Manual
DC: 091715
Digital Atomic Wall Clock
Get Started
Step 1: Insert 2 fresh AA, LR6 1.5 volt Alkaline batteries into the atomic
clock according to the polarity markings.
Time, Alarm +
WWVB Icon
Indoor Temperature,
Weekday, + Date
2-AA batteries
BUTTONS

WT-8005U www.lacrossetechnology.com/support Page | 2
IMPORTANT:
The clock will look for the Atomic time signal for 7 minutes when batteries
are first installed. Buttons will not function during the Atomic time
signal search.
Hold the WWVB SEARCH button for 3 seconds to stop the Atomic
signal search.
Manually set the time and time zone.
The clock will search for the Atomic time signal again after midnight.
Press WWVB SEARCH button anytime, to start an Atomic signal
search.
For information about Atomic Time, visit:
www.nist.gov/pml/div688/grp40/wwvb.cfm
Set Time, Date, 12/24 Hour
1. Press the SET button to enter time set mode, confirm
adjustments and move to next item.
2. Press the ▲ or ▼ buttons to adjust values.
Settings order:
1.12/24 Hour Format 2. Hour 3. Minutes 4. Year 5. Month 6. Date
7. Daylight Saving Indicator
Press SET to exit, or wait 30 seconds without pressing buttons to return
to the normal time display.
Time Zone/Temperature Units
Press the ZONE button to select your time zone.
oP= Pacific
oM= Mountain
oC = Central
oE= Eastern
Press the ºF/ºC button to switch from Fahrenheit to Celsius.
Set Alarm Time
Hold the ALARM button to set time alarm.
Press the ▲ or ▼ buttons to adjust values.
Press the ALARM button to confirm adjustments and
move to next item.
Setting order: 1. Hour 2. Minutes
Press ALARM to exit, or wait 30 seconds without pressing buttons to
return to the normal time display.
SET
▲ ▼
ALARM
ZONE ºF/ºC
▲ ▼

WT-8005U www.lacrossetechnology.com/support Page | 3
Deactivate/Activate Alarm
Press ALARM once to deactivate the alarm.
The alarm icon will disappear.
Press ALARM once to activate the alarm.
The alarm icon will appear.
Snooze
Press SNOOZE to silence an active alarm for 5 minutes.
The alarm icon will flash.
This is a crescendo alarm that will sound for 120 seconds if not
deactivated. Press any button to stop the alarm for 24 hours.
Reset Button
If the atomic clock display appears distorted or is not
responding to buttons, use a pen or paperclip to press
RESET one time.
This will reset the atomic clock to default settings.
Specifications
Indoor:
Temperature Range:
14.1°F to +139.9°F (-9.9ºC to +59.9ºC)
Power:
Atomic clock
2-AA, IEC, LR6 batteries (not included)
Battery Life:
Atomic clock
Up to 24 months
Dimensions:
Atomic clock:
8.9” L x 1.2” W x 7.2” H
(226.06 L x 30.48W x 182.8 H mm)
Care and Maintenance
Do not mix old and new batteries
Do not mix Alkaline, Standard, Lithium or Rechargeable Batteries
Always purchase the correct size and grade of battery most suitable for
intended use.
Replace all batteries of a set at the same time.
Clean the battery contacts and also those of the device prior to battery
installation.
Ensure the batteries are installed with correct polarity (+and -).
Remove batteries from equipment with is not to be used for an extended
period.
Remove expired batteries promptly.
Alarm
Icon
SNOOZE

WT-8005U www.lacrossetechnology.com/support Page | 4
Warranty and Support Information
La Crosse Technology, Ltd. provides a 1-year limited time warranty (from date of
purchase) on this product relating to manufacturing defects in materials &
workmanship.
View full warranty details online at:
www.lacrossetechnology.com/warranty_info.pdf
For warranty work, technical support or other information contact:
La Crosse Technology, Ltd
2830 26th Street S.
La Crosse, WI 54601
Contact Support: Online Product Support:
1-608-782-1610 www.lacrossetechnology.com/support
Product Registration:
www.lacrossetechnology.com/support/register
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This device must not be co-located or operating in conjunction with any other antenna or transmitter.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Caution!
The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user authority to operate the
equipment.
All rights reserved. This manual may not be reproduced in any form, even in part, or duplicated or
processed using electronic, mechanical or chemical process without the written permission of the
publisher.
This booklet may contain errors or misprints. The information it contains is regularly checked and
corrections are included in subsequent editions. We disclaim any responsibility for any technical error or
printing error, or their consequences.
All trademarks and patents are recognized.
Canada Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions:(1) This device may not cause interference; and(2) This device must accept
any interference, including interference that may cause undesired operation of the device.