La Spaziale S1 Vivaldi II User manual

La Spaziale S1 Vivaldi II
Timer Instruction Manual
Rev. A - 3/06/2007
Notice: Do not expose timer to heat or moisture

LaSpaziale S1 Vivaldi II Timer Instruction Manual
Page 2 of 8
LaSpaziale Vivaldi II Clock Module
General Notes
a) With the selection of English as the language, the time of the day is shown in standard
HH:MM am/pm format on the first line. The date is show on the 2nd line in standard MM-
DD-YY format.
b) The clock module automatically adjusts for leap years.
c) The clock module automatically adjusts for Daylight Savings Time, if selected. However,
this feature has not been changed for the new US DST dates. Consequently, it is best to
leave this feature off.
d) The times and dates on your timer may be different than shown in this manual since they
will depend on how your unit was previously set when entering configuration mode.
1. OPERATING INSTRUCTIONS
With power on, the first line displays the current time (01:00pm). The second line alternates
between the current date and the next off “OF” or on “ON “ time (OF08:30pm), if an on/off
operation is pending before midnight of the current day.

LaSpaziale S1 Vivaldi II Timer Instruction Manual
Page 3 of 8
1.1 Timer programming
Pressing the button for about 3 sec. enters the programming mode with the word “Timer
Selectio” displayed. Use the buttons to select the desired mode then confirm with
the button
1.2 “Language Selectio” Mode
Confirm Language mode with the button and on the display the language previously
selected is flashing.
On the top line: Selectio
On the bottom line: English (flashing)
Use the buttons to select the language among: Italian – English – French – German
– Spanish and confirm with .
1.3 “Clock Selectio” Mode
With the button confirm Clock mode. The following message is shown on the display:
On the top line: Day
On the bottom line: Monday (flashing)
With the buttons select the day of the week and confirm with .
The following message is shown on the display:
On the top line: Month
On the bottom line: January (flashing)
With the buttons select the month and confirm with .
Timer
Selectio
Language
Selectio
Clock
Selectio

LaSpaziale S1 Vivaldi II Timer Instruction Manual
Page 4 of 8
The following message is shown on the display:
On the top line: Day
On the bottom line: 30 (flashing)
With the buttons select the date of the week and confirm with .
The following message is shown on the display:
On the top line: Year
On the bottom line: 2007 (flashing)
With the buttons select the year and confirm with .
The following message is shown on the display:
On the top line: Time
On the bottom line: 12:00am (with the hour digit flashing)
With the buttons select the hour including am/pm and confirm with .
The digits of the minutes start flashing. With the buttons set the minutes then press .
The displayed message changes to:
On the top line: Summerti (Daylight Savings Time)
On the bottom line: NO – YES (with flashing Yes)
With the buttons select:
YES = Change to Daylight Savings Time on the last Sunday of March at 02:00am and change
back to Standard time on the last Sunday of October at 03.00am.
NO = No change to summer time (DST) occurs.
then press . The display then shows Clock Selectio. Press to cycle back to the
beginning of Clock Selectio mode or to exit programming mode.
1.4 “Timer Slectio” Mode
With the button confirm Timer mode. The following message is shown on the display:
On the top line: Timer
On the bottom line: OFF – ON (with flashing ON)
With the buttons select:

LaSpaziale S1 Vivaldi II Timer Instruction Manual
Page 5 of 8
OFF If you want to disable use of the timer function to turn the S1 on and off.
ON If you want to enable the timer to turn the S1 on and off at the programmed times, then
confirm it with the button
The display then changes to:
On the top line: Monday (flashing)
On the bottom line: ----------
With the buttons , select the day and then confirm with button . The selected day
becomes fixed and abbreviated followed by the message:
On the first line: Mon 1º ON
On the second line: 12:00am (with the first two flashing digits)
With the buttons select the hour and confirm with ..
This makes the digits corresponding to the minutes flash. With the buttons select the
minutes and confirm with . The message Mon 1º ON becomes Mon1º OFF. On the
second line: 12:00am (with the first two flashing digits)
Use the same procedure as above to select the first hour for OFF. By confirming it, the
message Mon 1º OFF becomes Mon 2º ON and, once it is confirmed, it becomes Mon 2º
OFF. The same procedure is valid for the 3rd time setting. Once the Mon 3º hour of OFF is
programmed, the display changes to:
Top line: Tuesday (blinking)
Bottom line: Copy
If you want to copy the setting made the previous day, you have to press the button and
hold for three seconds. If you wish to copy a single day’s schedule such as Mondays all the
way through Friday, for example, press again and hold the button for 3 seconds as you
cycle through each day. If you want to just move to the next day to set up a schedule different
than that just programmed, momentarily press the button. You can then program the
next and and subsequent days for up to three different On / Off times just as the Monday
example described above. After each day you can press for three seconds to copy to
the next day or momentarily press the button to move to the next day.

LaSpaziale S1 Vivaldi II Timer Instruction Manual
Page 6 of 8
After selecting the last day of the week, you go back to the “Timer Selectio” display. Press
to cycle back to the beginning of Clock Selectio mode or to exit programming mode.
Special Case Settings:
!If the ON and OFF time are both set to the same time, the machine remains off.
!If the ON time of the next time setting is the same as the OFF time of the previous
setting, the machine stays on.
!If there is one minute of difference (OFF 11:59pm - ON 12:00am) between the OFF time
of one specific day and the ON time of the following one, the machine stays on.
2. EXAMPLES OF TIMER PROGRAMMING
1st example:
In case you want to switch on the machine at 07:00am and switch it off at 09:00pm during the
whole week, proceed as follows:
Press for 3 sec. the button , confirm Timer Selectio mode with the button . Select
“TIMER ON” with the buttons , then confirm with .
The first line of the display shows Monday, confirm with the button .
Set with the buttons 7:00am as time and confirm with the button . Set the minutes
as 00 and confirm with the button (for programming instructions see paragraph 1.4).
The display shows on the first line MON 1º OFF, set with the buttons 09:00 pm as
time and confirm with the button , then set the minutes 00 and confirm with the button
.
Set the following times all to 9:00PM and confirming each with the button (Mon 2º ON,
Mon 2º OFF, Mon 3º ON, Mon 3º OFF) until the display shows Tuesday on the first line and
COPY on the second line.
Press button for 3 sec. so as to copy the time setting of the previous day. The display
shows Wednesday on the first line and COPY on the second line.

LaSpaziale S1 Vivaldi II Timer Instruction Manual
Page 7 of 8
Press the button for about 3 sec. so as to copy the time setting of the previous day.
Repeat the same operation for all days of the week.
After selecting the last day of the week, the display returns to “Timer Selectio” mode.
2nd example:
In case you want to set a day of the week for which the machine does not turn on (for
example Sunday) proceed as follows:
Set the desired on and off time of all days of the week (for programming instructions see
paragraph 1.4). When the Timer displays Sunday, confirm with the button .
With set the ON and OFF time at 12:00am in the first time setting. Confirm the same
time for all the following time settings with the button .
3rd Example:
In case you want to switch on the machine from 07:00am Monday through 11:00pm on
Saturday proceed as follows:
Press for 3 sec. the button . Select "TIMER ON" with the buttons .
The first display line shows Monday. Confirm with the button .
Set with the buttons 7:00am as Mon 1º ON and confirm with the button (for
programming instructions see paragraph 1.4).
The display shows on the first line MON 1º OFF. Set with the buttons 11:59pm as
Mon 1º OFF and confirm with the button .
Set the following times all to 12:00am and then confirm each setting with button : (Mon
2º ON, Mon 2º OFF, Mon 3º ON, Mon 3º OFF) until the display shows TUESDAY on the top
line and COPY on the bottom line.
Press the button and set as Tues 1º ON time 12:00am. Confirm with the button
The display shows on the first line Tues 1º OFF. Set with the buttons 11:59 pm as
Mon 1º OFF and confirm with the button .

LaSpaziale S1 Vivaldi II Timer Instruction Manual
Page 8 of 8
Set the following times all to 12:00am and confirm each setting with the button (Tues 2º
ON, Tues 2º OFF, Tues 3º ON, Tues 3ºOFF) until the display shows WEDNESDAY on the
first line and COPY on the second line.
Press the button for 3 sec. so as to copy the time settings of the previous days. Repeat
the same operation for all the other days until the display shows Saturday. Confirm with the
button . Set the time 12:00am ( Sat 1º On) and confirm with the button . The display
shows Saturday time Sat 1º OFF on the first line. Set the time to 11:00pm (Sat 1º OFF) and
confirm with the button .
Set the following times to 11:00PM and confirm with the button (Sat 2º ON, Sat 2º OFF,
Sat 3º ON, Sat 3ºOFF) until the display shows SUNDAY on the first line and Copy on the
second line.
With the buttons set ON and OFF at 12:00am in the first time setting. Confirm with
the button the same time for all the other time settings.
After selecting the last day of the week the display goes back to the “Timer Selectio” mode.
3. Battery Backup
When power is off to the Vivaldi II, there is no power provided to the timer. In this mode the
timer display is off but the time and program are maintained in battery backed memory. A 3V
CR2032 Lithium button battery is used for this purpose. This battery should last for several
years.
4. Other Operational Notes
!There is no Back button. If you make an error or miss a critical step, you need to just
stop and wait for the programming mode to time out. The timer will then revert to time
mode and you can start over with programming.
!If you can’t figure out how to get the timer to do what you want from this manual,
please log into the S1 forum and ask for assistance: http://s1forum.rimpo.org.
!This manual assumes that you have purchased your S1 Vivaldi II with Timer option
installed. If you purchased your timer later, please request installation assistance from
Chris Coffee Service: http://www.chriscoffee.com/contact.