La Spaziale Mini Vivaldi User manual

LA SPAZIALE
MINI VIVALDI
INSTRUCTION MANUAL

Page 1
TABLE OF CONTENTS
1!Feature Overview......................................................................................................3!
2!Reference Photos .....................................................................................................4!
3!Document Scope – Caveats and Clarifications.........................................................5!
4!Basic Machine Operation ..........................................................................................5!
4.1!15 Amp or 20 Amp Operation (READ ME FIRST) .............................................5!
4.2!Optional On/Off Timer Accessory – Overview and WARNING..........................6!
4.3!Initial Installation Before Connecting Power ......................................................7!
4.4!Filling the Water Tank ........................................................................................8!
4.5!Turning On and Heating the Machine ................................................................9!
4.6!Espresso Brewing ............................................................................................10!
4.7!Volumetric Dose Programming ........................................................................10!
4.8!Hot Water Delivery...........................................................................................11!
4.9!Steam Delivery.................................................................................................11!
4.10!Boiler Operational Modes ................................................................................12!
4.11 ! Espresso Group Water Temperature Regulation ..........................................13!
4.11.1!Standard Temperature Adjustment...........................................................13!
4.11.2!Offset Temperature Adjustment................................................................14!
4.11.3!Steam Pressure Adjustment .....................................................................16!
4.11.4!Extreme Temperature Set Function..........................................................18!
5!Alarm Handling........................................................................................................19!
5.1!No Water in Tank .............................................................................................19!
5.2!Coffee Group Water Dosing System Failure....................................................19!
5.3!Coffee Group Temperature Detection System Failure.....................................19!
5.4!Steam Boiler Temperature Detection System Failure......................................19!
5.5!Damaged Group Heating Element Triac / SSR ...............................................20!
5.6!Damaged Boiler Heating Element Triac SSR ..................................................20!
5.7!Boiler Automatic Refill System Failure.............................................................20!
6!Connection Diagrams..............................................................................................21!
6.1!Electrical Connection Diagram.........................................................................21!
6.2!Control Board Connection Diagram .................................................................22!
6.3!Triac Board Connection Diagram.....................................................................22!
6.4!Control Panel Connection Diagram .................................................................23!
6.5!Wiring Diagram Definitions ..............................................................................23!
7!Mini VII Water Flow Diagram...................................................................................24!
8!Adjustments and Maintenance................................................................................24!
8.1!Group Pressure Adjustment.............................................................................24!
8.2!External Mini VII Surface Cleaning ..................................................................25!
8.3!Routine Group Cleaning ..................................................................................25!
9!Optional Accessories ..............................................................................................26!
10!Other LaSpaziale Mini VII Resources .....................................................................30!

Page 2
11!Quick Setting Guide ................................................................................................31!

Page 3
1 Feature Overview
Dual Boiler
Steam Boiler 1.2 liter
Comes with NEW .9 mm 4-Hole Steam Tip
Steam Boiler Element 1250 Watts
Group Boiler .45 liter
Group Boiler Element 800 Watts
Programmable Offset Differential
Swivel Stainless Steel Steam Arm
Two 53 mm Portafilters: One Single and One Double
Manual Fill 3 liter Water Tank
Vibratory Pump (Extremely Quiet)
Volumetric Dosing
Volumetric Dosing Adjustable Through Touch Pad
One Degree Group Temperature Adjustability Indicated by LED Display
Group Temperature Adjustable Through Touch Pad
Electronic Boiler Refill
Built-in Safety Thermostat
Built-in Safety Cut Out on Vibe Pump
Semiautomatic Hot Water Delivery
Lever Steam Valve same as La Spaziale S5 Commercial Machines.
Fault Diagnosis Alarms
Dual Manometer
OPTIONAL Pre Infusion Chamber
OPTIONAL Timer
OPTIONAL No Burn Steam Arm
OPTIONAL longer La Spaziale steam arm
OPTIONAL Drain Kit
Color Black or Red
110 volt
ETL Sanitation Listed (Conforms to ANSI/NSF STD 4)
ETL us Listed (Conforms to UL STD 197 Certified to CAN/CSA STD C22.2 NO.109

Page 4
2 Reference Photos
These numbered photos will be referenced throughout the document; i.e. (13)

FIGURE 1 – Indicator Lights and Control Buttons
Label
Function
Label
Function
Label
Function
Label
Function
1
Drip Tray
9
Control Panel
17
94°C Lamp
25
Double Cup
Button
2
Steam Arm
10
Group
18
95°C Lamp
26
Boiler Button
3
Rubber Feet
11
Portafilter
Handle
19
96°C Lamp
27
On/Off Button
4
Water Tank
12
Drip Tray Grate
20
97°C Lamp
28
Hot Water
Outlet
5
Side Panels
13
Boiler Lamp
21
Empty Water
Tank
29
Steam Pressure
Gauge
6
Steam Lever
14
91°C Lamp
22
On/Standby
Lamp
30
Group Pressure
Gauge
7
Cup Warming Tray
15
92°C Lamp
23
Hot Water
Button
8
Splash Panel
16
93°C Lamp
24
Single Cup
Button
3 Document Scope –Caveats and Clarifications
This manual includes material that both duplicates and enhances the official LaSpaziale
S1 Mini Vivaldi Instruction Manual in key areas. However, it does not duplicate the
detailed and very important information covering machine certifications or ratings nor
does it repeat all the warning and safety information contained on the “lawyer” pages.
That information, as contained in LaSpaziale Instruction Manual Part # LSC 014-UK
Rev.00 or later, is considered included in this document by reference.
The official LaSpaziale S1 Mini Manual covers the Mini Vivaldi I and the Mini Vivaldi II
plus one option not currently offered or required in the consumer market. That option, as
well as material intended specifically for the Mini Vivaldi I, has been omitted from this
document.
This document solely covers the S1 Mini Vivaldi II plus options available and supported
by Chris Coffee Service and/or other vendors supplied by Chris Coffee Service through
its exclusive distribution agreements with La Spaziale S.p.A.
4 Basic Machine Operation
(BOLD = lamps, Reverse = buttons, numbers in parentheses reference to above table)
4.1 15 Amp opperation
The La Spaziale Mini Vivaldi previously could operate in either 15 amps or 20 amps,
however effective 2019 they can only be run in 15amps. When purchased a convertor
cord will be included free of charge.
Page 5

Most modern kitchens have 20 amp circuits so if you're looking for a machine to run in
20 amps you may want to consider the Spaziale Dream T instead.
The advantage of using it in 20 amps is that both boilers can reheat simultaneously
therefore giving you better recovery and less concern for running out of steam power.
This tends to not be an issue with any Spaziale machine regardless of 15 vs. 20 amp
operation due to their incredible steam pressure.
Note: new machines use a dual Solid State Relay (SSR) rather than the triac.
4.2 Optional Bluetooth Digital Timer - On/Off Capabilities
We all love La Spaziale Vivaldi S1 and Mini S1, but it is missing one important
feature– warm up schedule and remote power on/off. Let’s face it, the timer supplied
by La Spaziale is expensive and outdated. We now have a smaller, better, and
cheaper version. Now you can schedule warm up of the Vivaldi S1, remotely turn it
On or Off via phone and ask Google, Alexa or Siri, to control it.
Page 6
CONVERTOR CORD

The S1 Power Retain Timer is installed the same way the factory timer is. It plugs into a
pre-wired connector inside the machine. The S1 power cable is then plugged into a
smart plug outlet. A smart plug outlet (not provided) is what controls the power to the
machine. There are a number of smart plug outlets available on the market. Use the
smart plug outlet provided phone application to schedule the Vivaldi turn On and Off
times. Any smart plugs with scheduled On/Off will work. The S1 Power Retain Timer
turns the machine on as soon as it gets the power from the smart plug outlet.
Must haves
External smart plug outlet (min. 15amp capacity) is required and sold separately. Use
any smart plug outlet with schedule On/Off capabilities. Most smart plug outlets are sold
for around $25 and have an app to control them remotely.
Must know
This will only be able to work using the machine in 15amp / half power mode. The smart
outlet uses a mechanical relay designed with a safety margin to operate with constant
max load.
4.3 Initial Installation Before Connecting Power
After removing the Mini VII from its packing carton and setting it on the counter, check
for additional installation instructions that may be included. You should also have all the
accessories shown in the photo below plus a rubber backflush disk (not shown).
Tip the Mini VII on its side. Twist all four rubber feet (3) hand tight as they may vibrate
loose during shipping. While performing that task, use a screwdriver to ensure that the
four screws on the bottom (two on each side between the rubber feet) which fasten the
two side panels (5) to the chassis bottom are tight. These steps will help ensure the
quietest possible operation of your Mini VII.
Page 7

Page 8
Important Tip: Your Mini VII dealer may request that you check that your water
hardness is below a certain level to ensure long life and trouble free operation.
Hardness test strips may be included for this purpose. If your water fails this test,
contact your Mini VII dealer and discuss the available options. This test should be
done before using your machine. Water over 3 grains of hardness needs to be
softened or else consider using bottle water. Hard water will require frequent
descaling which is not a trivial procedure on this machine. Over time use of very hard
water could result in the need to replace the steam boiler heater element. Since the VII
Mini has a sealed boiler, replacement of the entire boiler is required. This is not an
inexpensive repair. Be forewarned. Use soft water.
4.4 Filling the Water Tank
•Remove the drip tray (1)
•Remove the water tank (4) and fill with soft water to ensure against mineral
buildup in your boilers
•Replace the water tank (4) and the drip tray (1)
•Insert the plug into the 110V AC socket, the On/STBY light (22) starts
flashing. (Stand-by mode).
•Press the ON/OFF (27) and Hot Water (23) buttons simultaneously. During
this stage, the control lights EMPTY and On/STBY (22) blink while the
pump runs
•Once you see water coming from the group (10), release both buttons. The
unit is now in Standby mode with the On/STBY light blinking. You have
now primed the pump and filled both boilers with water.
•machine includes an oscar softening pouch. Add this item to the tank to
help remove calcium and magnesium from hard water.
Important Tip: The above procedure is only required on the initial use of the
machine or any time when starting up with empty boilers such as after storage, boiler
clean out, shipment, etc. or any time the boilers have previously been drained.
Otherwise, once this procedure is performed once, it is only necessary to turn the
machine on using the ON/OFF (27) button. It is NOT required to perform the above
procedure each time the water tank is refilled.

Page 9
4.5 Turning On and Heating the Machine
1) Place the desired coffee basket (Single or Double) into one of the portafilter
handles and attach it to the group.
2) Insert the plug into the 110V AC socket, the On/STBY light (22) starts flashing.
(Stand-bymode).
3) Press the ON / OFF (27) and button and keep it pressed for about 3 seconds,
the green On/STBY light (22) changes from flashing to steady indicating the
machine is ON. At the same time the lights from (14) to (21) turn on steadily for
about a second (indicating power on test mode).
4) The light corresponding to the set temperature starts flashing to indicate that the
group is heating and the automatic boiler refill starts until the water level preset
by the manufacturer is reached.
5) Once the filling process is finished, the BOILER light (13) starts flashing to
indicate that the boiler is heating. However, after first switching on, the boiler
doesn't work until the group has reached the set temperature.
6) Fasten the portafilter handle (11) to the brewing group (10).
7) Wait until the set temperature is reached, by checking that the lights on the
control panel (9) gradually turn on as the temperature rises. The visualization
starts as soon as the temperature reaches 91°C (turning on of light 14) and

Page 10
continues until the machine has reached its operating temperature (light from
flashing to fixed).
8) When the group has reached the set temperature, the boiler heating starts
(BOILER light (13) flashing), once it reaches the set temperature the light
becomes fixed.
9) Every time the group temperature or the boiler temperature drops under the set
value, the respective light starts flashing (heating phase) until the set
temperature is reached.
10)The machine is now ready.
(26)
Important Tip: To activate and deactivate the boiler mode press the ON/OFF
button. When the unit it turned off, then back on or even unplugged, then plugged
back in, the Mini VII will remember the last state of the Boiler mode. When the
boiler is turned off, it is impossible to use hot water for infusions or steam delivery.
4.6 Espresso Brewing
1. Unfasten the portafilter handle (11) from the brewing group (10) and insert the filter
for one or Double Cups. Fill it with ground coffee, making sure not to leave coffee
powder on the upper edge of the portafilter handle (11), and press it with the
suitable coffee tamper provided.
2. Firmly attach the portafilter handle (11) to the brewing group (10).
3. Place one or Double Cups under the portafilter handle (11).
4. Press the button corresponding to Single Cup (24) if you want to make one coffee
or Double Cups (25) to start the delivery. Once the desired quantity of coffee
programmed is reached, the delivery automatically stops.
4.7 Volumetric Dose Programming
The programmable volumetric dosing feature allows programming of the Single Cup
(24) and Double Cup (25) buttons to dispense whatever quantities of espresso the
user desires. Their use for single cup and double cup quantities is merely a
suggestion. Many users only pull double shots and program the double shot button for
1.5-2.0oz for that purpose. Then they program the Single Cup button for a larger
amount for use in flushing the portafilter basket and/or the group between shots. The
beauty of the programmable dosing feature is that the machine owner can be creative.
The following are the instructions for programming each button assuming they are
being used for single and double shots.
1. With the machine on, press the ON//OFF (27) button and keep it pressed for about
3 seconds; the control light (22) and the one indicating the set temperature start
flashing.
2. Insert the single cup basket into the portafilter handle (11) and fill it with 7-8g of
ground coffee making sure not to leave coffee powder on the upper edge of the

Page 11
portafilter handle, and press it with the included plastic tamper or, more optimally, a
high quality 53mm coffee tamper.
3. Fasten the portafilter handle (11) to the brewing group (10), placing a cup under the
portafilter handle.
4. By pressing the Single Cup button (24) the delivery starts and the lights 14-15-16
turn on to show that the one shot espresso dose is being programmed.
5. When the coffee inside the cup has reached the desired quantity, again press the
button (24) to stop the delivery.
6. You automatically return to the initial visualization.
7. Repeat the previous steps above using the Double Cup button (25) making sure
you change the filter inside the portafilter handle (11) to the double shot basket and
fill it with 14-16g of espresso first.
4.8 Hot Water Delivery
(only possible with the boiler turned on, BOILER light 13 on)
1. Place the pitcher below the hot water output (28):
2. Press the Hot Water delivery push-button (23).
3. The hot water delivery starts.
4. Once the desired quantity is reached, stop the delivery by pressing the Hot Water
button (23) again.
Important Tip: The steam/hot water boiler on the V2 Mini is not very large. When
using it for hot water, it is suggested that no more than ~6oz be removed at a time
and then let the unit refill the boiler before using again. Otherwise, you run the
risk of exposing the steam boiler heater element while it is powered up and
possibly damaging it.
4.9 Steam Delivery
(only possible with the boiler turned on, light 13 turned on)
1. Insert the steam wand (2) in the pitcher containing the drink to be heated.
2. Push the steam lever (6) up, regulating the steam flow according to the need.
3. At the end of the heating phase of the drink, stop the steam delivery by pulling the
steam lever (6) all the way down.
4. Remove the pitcher from the steam wand (2) and wipe the steam wand and tip
immediately with a clean, damp sponge in order to remove all residue of the heated
drink.
5. NOTE: The steam lever (6) will remain in the all the way up position when released.
However, if released in any other position, the lever will automatically drop to the off
position.
Important Tip: Do not engage the steam lever (6) before placing the
steam wand (2) inside the pitcher, in order to avoid burns.

Page 12
4.10 Boiler Operational Modes
Both boilers are completely independent, turning on and off according to the
needs of each. Both can be on at the same time.
The BOILER button can toggle the Boiler on and off. This mode is useful for
those that only drink espresso and do not need steam or hot water and want
to conserve energy.
Important Tip: The state of the BOILER button is kept in memory and is
maintained through On/Standby cycles, when the unit is unplugged, or if
there is a power failure
Turning the Steam/Hot Water Boiler On and Off
1.
2.
The Mini VII must be in ON mode, not Standby for all operations below.
With the BOILER lamp on, press and hold the BOILER button until the BOILER
lamp turns off. Neither steam nor hot water is available.
As noted above, the Mini V2 remembers the current state of the BOILER
button through Off/On cycles, when the machine is unplugged, and through
power failures.
3. Press the BOILER button again until the BOILER lamp turns back on.
4. When the BOILER lamp is on (or blinking), steam and hot water are available.

Page 13
4.11 Espresso Group Water Temperature Regulation
4.11.1 Standard Temperature Adjustment
1. When the machine is On (ON/STBY solid green), press the button ON/OFF
and keep it pressed for 3 seconds, the control light (22) and the one concerning
the set temperature start flashing. For example, if the set temperature is 95°C,
light (18) starts flashing.
2. In order to change the operating temperature, press and release the Hot Water
button (23) Every press of the button corresponds an increase of the temperature of 1°C
(with the flashing of the corresponding light). When the maximum temperature of 97°C (20)
is reached, the selection restarts from the minimum temperature of 91°C (14) (cyclic mode).
3. Once you choose the desired temperature, in order to lock in this value, press
the ON/OFF (27) button, the machine will then go back to its normal functioning.
The value of the operating temperature of the machine is easily changed in order to
improve the final result in the cup depending on the coffee blend used and the user’s
personal preference.

4.11.2 Offset Temperature Adjustment
What Does Temperature Offset Do? / How Do I Use it?
The Vivaldi group design exhibits a temperature drop between where the group boiler
temperature probe is located and where the hot water exits the group. Consequently,
the temperature setting shown by the temperature lamps on the front panel may differ
from the water temperature at the group. Ideally, most users would prefer that the
temperature indicated by the temperate lamps exactly matches the water temperature
exiting the group. LaSpaziale has partially accounted for this in its basic design.
However, there are too many machine to machine electrical and mechanical variances
for this to be completely effective. That’s where the temperature offset comes in. The
programmable temperature offset allows a user with accurate group temperature
measuring equipment to enter an offset in the range of ±8˚C (for extended offset option
or 0 to -8˚C for standard offset option) in order to allow their machines temperature
lamps to exactly match the water temperature exiting the group.
Those purchasing new machines from Chris Coffee Service have had the temperature
offset professionally programmed used a Scace device. However, for those obtaining
the expanded offset capability via an upgrade, it is recommended that you note the
current offset prior to upgrading and then duplicate that offset using the instructions
below. If you do not know how to tell what your current offset is, you can find out by
entering the temperature offset mode and then following instructions in paragraph
4.11.2.
To Which Machines Do These Instructions Apply?
Instructions are given in the two sections below both. This first is for machines with
the original offset adjustment. The section that follows is for machines with the
extended temperature offset adjustment. In general if you purchased a new VII Mini
from Chris Coffee after 7/1/2008, then the extended offset instructions should apply.
If you are unsure, try both methods outlined below. Only one will work and then you’ll
know which version you have.
Page 14

Page 15
4.11.2.1 Standard Temperature Offset Adjustment
With the machine in Standby (only ON/STBY green lamp blinking), press the BOILER
button until the green ON/STBY lamp and the red BOILERlamp are blinking (about 10
seconds).
If the Offset = 0ºC, then no other lamps are lit. Assuming a start with Offset = 0ºC ,
each press of the BOILER button, changes the offset by -1ºC and lights an additional
lamp starting with the 91ºC lamp and going up through the ECON lamp. Once all eight
offset lamps are lit, an additional press of the BOILER button cycles back to 0ºC offset.
To exit the Offset mode, press ON/OFF (machine in Standby – ON/STBY blinking).
When entering the Offset mode the next time, the last stored value is displayed.
See table below:
Offset
91ºC
Lamp
92ºC
Lamp
93ºC
Lamp
94ºC
Lamp
95ºC
Lamp
96ºC
Lamp
97ºC
Lamp
ECON
Lamp
0ºC
Off
Off
Off
Off
Off
Off
Off
Off
-1ºC
On
Off
Off
Off
Off
Off
Off
Off
-2ºC
On
On
Off
Off
Off
Off
Off
Off
-3ºC
On
On
On
Off
Off
Off
Off
Off
-4ºC
On
On
On
On
Off
Off
Off
Off
-5ºC
On
On
On
On
On
Off
Off
Off
-6ºC
On
On
On
On
On
On
Off
Off
-7ºC
On
On
On
On
On
On
On
Off
-8ºC
On
On
On
On
On
On
On
On
4.11.2.2 Extended Temperature Offset Adjustment
Start with the machine in Standby mode (ON/STBY blinking green). Press and hold the
BOILER button for about 10 seconds until the Boiler light and the ON/STBY light start
flashing. You are now in the temperature offset programming mode.
To enter a positive temperature offset between 0˚C and +8˚C push the Single Cup
button. Each press will change the offset by +1˚C. An offset of 0˚C is designated by all
temperature lamps off. A +8˚C offset is designated by all temperature lamps plus ECON
on (Low Water on Mini VII Mini). If your positive offset is more than you wish, each
press of the Double Cup button changes the offset by -1˚C.

Page 16
To enter a negative temperature offset between 0˚C and -8˚C mode push the Double
Cup button. Each press will change the offset by -1˚C. An offset of 0˚C is designated
by all temperature lamps off. A -8˚C offset is designated by all temperature lamps plus
EMPTY on. If your negative offset is more than you wish, each press of the Single Cup
button changes the offset by +1˚C.
How Do I Tell If My Current Offset is Negative or Positive?
Example: You enter Offset Programming mode and see that three lamps are on. This
can indicate either ±3˚C. Which is it? Since each press of the Double Cup button
changes the offset by -1˚C, press it and see what happens. There will either be two or
four lamps lit. If four lamps are lit the offset must have been -3˚C since pressing
Double Cup always changes the setting by -1˚C with each press. If two lamps are lit
the offset was +3˚C. By pressing Double Cup the offset has changed to +2˚C.
-8 -7 -6 -5 -4 -3 -2 -1 0 +1 +2 +3 +4 +5 +6 +7 +8 ˚C Offset
----------------------------------------------------------!Single Cup Button
"--------------------------------------------------------- Double Cup Button
Note that neither the Single Cup nor the Double Cup button presses wrap around
when they reach the limit of their range. Once you get to +8˚C additional presses of the
Single Cup button do nothing. Same with the Double Cup button once -8˚C is reached.
See table below:
Offset
91ºC
Lamp
92ºC
Lamp
93ºC
Lamp
94ºC
Lamp
95ºC
Lamp
96ºC
Lamp
97ºC
Lamp
EMPTY
Lamp
0ºC
Off
Off
Off
Off
Off
Off
Off
Off
±1ºC
On
Off
Off
Off
Off
Off
Off
Off
±2ºC
On
On
Off
Off
Off
Off
Off
Off
±3ºC
On
On
On
Off
Off
Off
Off
Off
±4ºC
On
On
On
On
Off
Off
Off
Off
±5ºC
On
On
On
On
On
Off
Off
Off
±6ºC
On
On
On
On
On
On
Off
Off
±7ºC
On
On
On
On
On
On
On
Off
±8ºC
On
On
On
On
On
On
On
On
4.11.3 Steam Pressure Adjustment
Steam pressure can be adjusted up or down in 1, 2, or 3 increments of slightly less than
0.1 bar each. The overall pressure range is from approximately 0.9 bar to about 1.4

Page 17
bar. In reality this adjustment is changing the steam boiler temperature in increments of
1ºC and you get the resulting pressure change.
This adjustment starts with the S2V2 Mini in Standby mode (ON/STBY light flashing).
•Press and hold the One Cup button for 3 seconds.
•At this point the 94 ºC and 95 ºC yellow lamps will be on solid. If no other lights
come on, your pressure is at the default settings and has not previously been
raised or lowered from that setting.
•If additional lights are blinking here is the meaning:
Offset&
91ºC&&
Lamp&
92ºC&&
Lamp&
93ºC&&
Lamp&
94ºC&&
Lamp&
95ºC&&
Lamp&
96ºC&
Lamp&
97ºC&
Lamp&
ECON&
Lamp&
Default&
Off!
Off!
Off!
On&
On&
Off!
Off!
Off!
+1
Off!
Off!
Off!
On&
On&
Blinking&
Off!
Off!
+2
Off!
Off!
Off!
On&
On&
Blinking&
Blinking&
Off!
+3
Off!
Off!
Off!
On&
On&
Blinking&
Blinking&
Blinking&
@1&
Off!
Off!
Blinking&
On&
On&
Off!
Off!
Off!
@2&
Off!
Blinking&
Blinking&
On&
On&
Off!
Off!
Off!
@3&
Blinking&
Blinking&
Blinking&
On&
On&
Off!
Off!
Off!
•To increase steam pressure, press the Two Cup button. For each button press
the blinking lights will cycle through indicating 0, +1, +2, +3, then back to 0,
repeating this sequence for each Two Cup button press.
•To decrease steam pressure, press the Hot Water button. For each press the
blinking lights will cycle through indicating 0, -1, -2, -3, then back to zero,
repeating this sequence for each Hot Water button press.
•Once the blinking lights indicate your desired value, press the One Cup button to
save the value and exit the steam pressure adjustment mode as indicated when
the 94 ºC and 95 ºC lights turn off.
To check the current value for steam pressure without changing it, enter the adjustment
mode as indicated above, check the state of the blinking lamps, then immediately press
the One Cup button to exit back to Standby mode (ON/STBY light flashing). If you
previously changed this adjustment the blinking lights reflect your last setting.

Page 18
4.11.4 Extreme Temperature Set Function
Standard temperature programming described in section 4.10.1 allows a range from
91ºC to 97ºC in 1ºC increments. There may be times when the user desires a
temperature outside of this range. While the Offset mode described in section 4.10.2
could be used for this purpose, it is best to use the offset as intended. Once set
properly, the offset should be left alone. Instead, the VII Mini includes a mode
specifically for use in extending the temperature range above 97ºC or below 91ºC up to
a max of 3ºC. While the ability to extend the temperature above 97ºC is of limited use,
there are some types of coffee whose flavor is optimum in the 88ºC to 90ºC range.
Note that the method below only works if the master temperature is set to either
91ºC or 97ºC. If the temperature is set to 91ºC you can only use the instructions
below to lower the temperature by 1ºC, 2ºC, or 3ºC. If the temperature is set to
97ºC you can only use the instructions below to raise the temperature by 1ºC, 2ºC,
or 3ºC. Consequently you must use the instructions provided in section 4.10.1 to
set the master temperature to 91ºC or 97ºC BEFORE using the instructions below.
If this is not done, the instructions below for entering the Extreme Temperature
Set mode will work as described, but once in that mode attempting to a raise or
lower the temperature has no effect.
Instructions for programming this mode AFTER setting the master temperature to 91ºC
or 97ºC are:
•Start with the machine in Standby mode (ON/STBY light flashing).
•Press and hold the Two Cup button for ~3 seconds until lights 94ºC (17) and
95ºC(18) come on indicating that the Extreme Temperature Function setting
mode is active.
•If you start with the master temperature set to 97ºC, each time that the Hot
Water button is pressed, lights 96ºC (19), 97ºC (20), and Tank Low (21) will
switch on in succession. Each light indicates a 1ºC increase. All three lights on =
100ºC.
•If you start with the master temperature set to 91ºC, each time that the One Cup
button is pressed, lights 93ºC (16), 92ºC (15), and 91ºC (14) will switch on in
succession. Each light indicates a 1ºC decrease. All three lights on = 88ºC.
•Press the Two Cup button again to exit Extreme Temperature set mode and
return back to Standby mode
Note:
When you change the temperature of the 91ºC and/or 97ºC buttons
according to the above instructions, the change only remains in effect until
the temperature is changed. For example, if you change the 91ºC selection

Page 19
by 3ºC to yield 88 ºC, then later change the temperature to 93C, the next
time you select 91ºC, you will get 91ºC, not 88 ºC. If you wish to obtain
88ºC again you will need to follow the above instructions to reprogram in
the 3 ºC decrease.
5 Alarm Handling
The Mini VII uses computerized sensors to robustly handle Mini VII device malfunctions.
There are two types of alarms the Mini VII can generate:
Blocking Alarms – these are the most serious. The VII will turn itself Off and display
the alarm codes noted below when one of these alarms occurs.
Non-Blocking Alarms – These are informational only and, while they do represent an
error condition, the machine will continue to function.
5.1 No Water in Tank
When the tank (4) is out of water the red EMPTY light (21) comes on and remains on
until at least 1liter of water is added. The tank can hold up to 3 liters.
5.2 Coffee Group Water Dosing System Failure
When the flow meter isn't working properly or when the coffee grind is too fine, this is
indicated by the turning on of the lights 14-15-16; if you are making one coffee dose,
and the lights 17-18-19 if you are making two coffee doses. This is a non-blocking
alarm. This alarm is actually useful when back flushing as an indication of when to turn
off the pump and allow the 3-way valve to operate.
5.3 Coffee Group Temperature Detection System Failure
This alarm is a blocking one, and occurs when the temperature probe of the group is in
short circuit (temperature >145°C) or is in open circuit (disconnected) condition
(temperature <60°C). The lights 20-21 turn on.
If the group water temperature does not exceed 60°C within 5 minutes of turning the
unit on, this alarm will also occur.
Turn off the Mini V2 and request service.
5.4 Steam Boiler Temperature Detection System Failure
(only with the boiler turned on)
This is a blocking alarm and occurs when the temperature probe of the boiler is in short
circuit (temperature >145°C) or it is in open circuit (disconnected) condition
(temperature <60°C). The lights 19-20-21 turn on.
The alarm can be temporarily cleared by turning the boiler off (Press BOILER (26)
button.) Eventually you will need to turn off the Mini V2 and request service.