Labgear LABGT18A User manual

Installation Instructions
Features include:
• 15.0dBi Gain
• F type connector for secure and easy connection
• Fast simple assembly
• Compact pack for easy transportation
Congratulations on the purchase of your LABGT18A aerial. The aerial is designed to get the best reception
from group A transmitters and receives signals between 470 and 606MHz. The high gain performance makes
it ideal for reception in fringe areas.
For optimum results install the aerial using double screened CAI benchmarked digital coax cable
and screened coax outlets. You will need to t the coax cable with the F type connector
supplied to connect to the downlead (not supplied) to the F socket on the aerial.
1. Prepare the Coax Cable: First fit the rubber weather boot provided, to the aerial end of
the cable. Strip the end of the cable as shown in Fig. 1. Once you have stripped the
cable, twist the braid and pull it back on itself, make sure that no braid is touching
the copper core, this will cause a short on the cable and you will not get any signal.
2. Fitting the F connector: Now, simply twist on the ‘F’ connector supplied and trim
the central conductor.
fold braid back
over sheath
8mm
inner
wire
cut or tear
away foil
6.5mm
Fig. 1
screw connector
body onto cable 2mm approx.
end of insulation
should be flush
with this face
Fig. 2
For best results the aerial should be mounted on an outdoor aerial mast and pointed
in the direction of the nearest transmitter* making sure it is in a position where the
transmitter signal will not be obstructed by nearby trees and buildings. If you are in
any doubt about the direction in which the aerial should be pointing or the
orientation of the aerial (horizontal for main transmitter, vertical for relay transmitter)
check your neighbours’aerials.
18 Element High Gain Group A Yagi Aerial
The aerial requires some assembly.
If mounting on an existing mast check that the mast is in good condition and rmly xed.
LABGT18A
USER GUIDE
Fitting the reflectors
Fig. 4
Lte 800
READY
reflector
element
reflector boom
assembly
Aerial assembly
Fig. 3
5. The central boom comes in two sections
using the bracket supplied and the holes
drilled in the boom sections join these two
sections as shown in Fig. 3.
7. Slide the reectors into the sockets
mounted on the central boom until
they click into place as shown in Fig. 4.
6. Attach centre mount bracket in the
position shown in Fig. 5. using the
clips supplied.
Fig. 5
centre
bracket
centre
bracket
clamps

4. Fit the mast clamp attached to the aerial centre bracket onto the mast.
Then slide the centre bracket through the mast clamp to find the most
evenly balanced position. Make sure the aerial is pointing in the direction
of the nearest TV transmitter then tighten the wing nuts until the aerial is
securely fixed into position, see Fig. 6.
5. Connect the aerial downlead to the ‘F’socket on the
underside of the balun (be careful not to over tighten
the F connector) see Fig. 6.
6. Slide the weather boot over the ‘F’connector
and socket to make a good seal - see Fig. 6.
7. Make sure that the downlead is routed as shown in Fig.6
making sure the lead doesn’t touch the reector.
Use insulating tape, to secure the coax downlead to
the mast.
8. Finally connect the aerial to your TV/set top box
and check the picture. Fine adjust the direction
of the aerial to obtain the optimum signal reception.
No picture:
Check all connections from aerial to TV.
Poor picture:
Check all connections from aerial to TV.
Check aerial is properly aligned to the correct transmitter.
If the aerial has been loft mounted try mounting outside.
Make sure new digital coax cable has been used
throughout the installation.
Check the transmitter signal is not obstructed by nearby trees
or buildings.
If in a very weak signal area or for long cable runs,
installing a masthead amplifier will improve the signal.
If in a strong signal area the signal strength may need to be
reduced by fitting an attenuator.
Caution
When mounting the assembled aerial, always observe safety
precautions and use the correct equipment.
Unless you are competent in the use of ladders and other
access equipment, do not work outdoors at roof height.
If in any doubt, refer to a qualied aerial installer.
Troubleshooting
© Philex Electronic Ltd. 2014. v1
Useful Websites for Digital Advice:
*To nd out which DTT channels should be available locally and
to nd out where your nearest transmitter is visit:
http://www.digitaluk.co.uk/coveragechecker/
and enter postcode, house number if you also check the detailed
view box you will see a list of transmitter’s with distances and
compass bearings.
For further information, please contact:
Customer careline: 08457 573479 (Local Rate - UK Only)
Technical Support: www.philex.com/support/
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist.
Check with your Local Authority for recycling advice.
Troubleshooting
Frequency Range MHz 470-606
TV Channels 21-37
Forward Gain dBd 12.8
Forward Gain dBi 15.0
Front/Back Ratio dB >15.0
Beam Width +/-deg. +/-18°
PCB Balun Yes
Connector F-Type
Length 1285mm
Width 345mm
Height 325mm
Fig. 6
Insulating
Tape
F Connector
Weather
Boot