LamasaTech Zentron 8 User manual
Contents
Configuring Hardware:
Hardware set up
Configuring MIPS Scanning Application:
Accessing the settings interface
Body temperature setting
Identification parameter settings
Volume settings
Startup settings
Recognition effect display
Password settings
Camera resolution preview settings
Lock screen brightness settings
Restart time setting
Relay settings
Others
Face data entry
Pass record
Face database
How to change the date and time on the Kiosk
Configuring VisiPoint Lite:
Configuration: Access the VisiPoint Lite application
Email alerts
Badge printing
Updating the Device Software
Check the Software version
Update the software
VisiPoint Lite installation
5
7
28
29
31
33
34
34
35
36
36
36
37
37
39
40
41
42
42
43
44
46
48
50
51
52
54
02
Hardware range
03
LD-AITemp-Device (Gen 1) Zentron 8 (Gen 2)
Non-touchscreen
Facial recognition
Permanent temperature sensor
RFID reader
Touchscreen
Facial recognition
Detachable temperature sensor
RFID reader
QR code scanner
HDMI output
Configuration range
04
Floor stand and
badge printer Desktop Kiosk
Wall Mount
Surface Kiosk
Configuring Hardware
05
Kiosk placement
Do not place the device directly :
- Facing the sun or in a location where the sun is directly facing the person
- In front or near an air outlet of an air conditioning or radiator device during measurement
- In front or near to strong infrared emitting light
- In a room where heating/cooling ducts are in the ceiling or directly below ceiling ducts
The above can cause changes to the forehead temperature. Measurements should be
taken in a stable environment.
Do not measure body temperature in an environment with:
- Strong electromagnetic interference (examples include places close to a working
microwave, induction appliances) as EM interference may cause errors in the reading
or even device failure.
06
08
Desktop Kiosk set-up
01. Unscrew the safety bolt
from the Kiosk
02. Thread the kiosk cables
through the desktop stand
03. Put the Kiosk into the desktop
base and line kiosk up with the light
on the desktop base
04. Re-screw the safety bolt
back on after attaching the
desktop base
09
05. Connect the different cables from the desktop base
into the Kiosk cables, there should be an Etherent, USB
and a Power cable to connect
06. Plug into the mains power
then turn on your Kiosk
07. Enjoy your Kiosk!
Floor stand & kiosk set-up
01. Unscrew the screws from
the bottom of the stand using
the provided allen key
03. Unscrew the safety bolt
from the Kiosk
02. Line up the stand with the
base and reattach screws
04. Unthread the kiosk cables
through the safety bolt
11
05. Thread the base plate
through the cables
06. Re-thread the safety bolt
over the cables and secure
onto the kiosk mount
07. Connect the different cables from the floor
stand into the Kiosk cables, there should be an
Etherent, two USB’s and a Power cable to connect
12
08. Using the allen key provided screw all 4
screws into the base plate and floor stand
09. Connect kiosk to mains power
and press power button
10. Enjoy your kiosk!
13
Adding a printer mount to a
floor stand
03. Thread the base plate that
came with the the printer mount
through the cables (not the base
plate that was on the floor stand)
02. Unthread the kiosk cables
through the safety bolt
01. Unscrew the safety bolt
from the Kiosk
04. Re-thread the safety bolt
over the cables and secure
onto the kiosk mount
15
05. Access the bottom of the floor stand and
thread the printer power supply up the kiosk
till it joins the other cables
06. Connect the different cables from the floor stand into
the Kiosk cables, there should be an Etherent, USB, a
Power cable and the printer USB to connect
16
07. Using the allen key provided screw all 4
screws into the base plate and floor stand
08. Unscrew the cable tidy slot so
you can access the holes to attach
the mount to the kiosk
09. Attach the mount to the
stand
17
10. Re-attch the cable tidy 11. Unscrew base plate on the
badge printer
12. Connect the badge printer to the
kiosk and power cable
18
13. Line up the badge printer screw
holes with holes in the printer mount
and reattach the printer for security
14. Connect kiosk to mains power and
press power button
15. Enjoy your kiosk and
badge printer!
19
This manual suits for next models
2
Table of contents
