Lancom GS-1108 User manual

쮿Handbuch
쮿Manual
110641/1208
LANCOM Systems GmbH
Adenauerstr. 20/B2
52146 Würselen
Germany
E-Mail: [email protected]
Internet www.lancom.eu
LANCOM GS-1108
...connecting your business
110641_GS-1108_cover.indd 1110641_GS-1108_cover.indd 1 12.12.2008 12:20:3112.12.2008 12:20:31

LANCOM GS-1108

© 2008 LANCOM Systems GmbH, Wuerselen (Germany). All rights reserved.
While the information in this manual has been compiled with great care, it may not be deemed an assurance of product
characteristics. LANCOM Systems shall be liable only to the degree specified in the terms of sale and delivery.
The reproduction and distribution of the documentation and software included with this product is subject to written per-
mission by LANCOM Systems. We reserve the right to make any alterations that arise as the result of technical develop-
ment.
All explanations and documents for registration of the products you find in the appendix of this documentation, if they
were present at the time of printing.
Trademarks
Windows®, Windows Vista™, Windows XP®and Microsoft®are registered trademarks of Microsoft, Corp.
The LANCOM Systems logo, LCOS and the name LANCOM are registered trademarks of LANCOM Systems GmbH. All other
names mentioned may be trademarks or registered trademarks of their respective owners.
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit http://www.openssl.org/.
This product includes cryptographic software written by Eric Young ([e-mail]).
This product includes software developed by the NetBSD Foundation, Inc. and its contributors.
This product includes the LZMA SDK written by Igor Pavlov.
This product includes components available in source code as Open Source software with specific licenses and copyrights
of various authors. In particular the firmware incorporates components which are subject to the GNU General Public
License, version 2 (GPL). The license agreement including the text of the GPL can be found on the product CD in the product
folder. The source codes and all license texts can be obtained from LANCOM Systems GmbH FTP server electronically upon
request.
Subject to change without notice. No liability for technical errors or omissions.
LANCOM Systems GmbH
Adenauerstr. 20/B2
52146 Wuerselen
Germany
www.lancom.de
Wuerselen, February 2009
110641/0209

LANCOM GS-1108
쮿Chapter 1: Introduction
3
EN
1Introduction
Optimally attuned to the LANCOM product portfolio, the LANCOM GS-1108
facilitates the structured cabling of small offices with up to eight networking
devices. Each connection port can automatically recognize the data-transfer
speed of networking equipment connected to it (10,100 or 1000 Mbit) as well
as the PIN assignment of the network cable (auto MDI/X).
1.1 Package content
Before beginning with the installation, please check that nothing is missing
from your package. Along with the device itself, the box should contain the
following accessories:
Should anything be missing, please take up immediate contact to your dealer
or to the address on the delivery note supplied with your device.
LANCOM
GS-1108
Power cord ✔
Printed documentation ✔
Rubber pads ✔

LANCOM GS-1108
쮿Chapter 2: Installation
4
EN
2 Installation
This section introduces your device. You will find an overview of all status dis-
plays and connectors here.
2.1 Status displays
Status displays on the front of the device provide information about opera-
tional and connection status:
LANCOM GS-1108
Power This LED provides information on the device's operating state.
Link/Act LAN connector status
10/100/1000
Mbps
Network connection status

쐇쐋
Off Device switched off.
Green On (perma-
nently)
Device operational.
Off No networking device attached
Green On (perma-
nently)
Networking device attached, no data traffic
Green Flickering Data traffic
Off 10-Mbit connection to networking device
Orange On (perma-
nently)
100-Mbit connection to networking device
Green On (perma-
nently)
1000-Mbit connection to networking device

LANCOM GS-1108
쮿Chapter 2: Installation
5
EN
2.2 Device connectors
All connectors are located on the front or back panel:
LANCOM GS-1108
쐃10/100/1000Base-TX connectors
쐇Connector for the supplied power cord
2.3 Hardware installation
Installation of the LANCOM GS-1108 involves the following steps:
햲LAN – by means of a suitable Ethernet cable, connect networking devices
to an available LAN port 쐃on the LANCOM GS-1108. The LAN ports are
only suitable for connecting non-PoE-capable networking devices! Alter-
natively, PoE-capable networking devices which are connected to ports
can be supplied with power via a PoE injector (e.g. LANCOM PoE Power
Injector) located in between.
The ports use autosensing to recognize the data rate (10/100/1000 Mbit)
and the type (node/hub) of attached network devices. It is possible to con-
nect devices of different speeds and types in parallel.
Use only network cables of category Cat 5 or better. For data transfer
in full-duplex mode (100 or 1000 Mbit), the length of cable between
the LANCOM GS-1108 and the connected networking device should
not exceed 100 meters.
햳Power supply – the socket 쐇is for connecting the supplied power cord.
Use only the supplied power cord! The use of the wrong power cord
can be of danger to the device or persons.

쐇

LANCOM GS-1108
쮿Chapter 3: Appendix
6
EN
3 Appendix
3.1 Performance and characteristics
LANCOM GS-1108
Standards Media 10BASE-T: UTP Cat. 3, 4, 5 or better
100BASE-TX: UTP Cat. 5 or better
1000BASE-TX: UTP Cat. 5 or better
IEEE IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab 1000BASE-TX
ANSI/IEEE IEEE 802.3 Auto-negotiation
Operating modes Switching Store and forward
Auto MDI/MDI-X Yes
Transfer mode 10/100Mbps, full/half-duplex (auto-sensing)
1000Mbps, full duplex
Transfer rate 10Mbps: 14880pps (64-byte packets)
100Mbps: 148800pps (64-byte packets)
1000Mbps: 1488000pps (64-byte packets)
Flow control IEEE 802.3x flow control for full-duplex
Back pressure in half-duplex operation mode
Display LEDs for Power, Link/Act, Speed
Hardware Power supply 100 - 240V, 50 - 60Hz, internal power supply unit
Environment Temperature range 0-40°C; humidity 0-90 %; non-condensing
Housing Metal housing, connections on the front; measures 197.2x
35.2 x 120 mm (W x H x D)
Power consumption (max.) max. 10 Watt
Weight 1kg
Approvals Conformity CE conform with DIN EN 55022 and DIN EN 55024
RoHS Compliance
Package content Cable IEC cable
Manual Printed Quick Installation Guide (DE/EN)
Item numbers LANCOM GS-1108 61457

LANCOM GS-1108
쮿Chapter 3: Appendix
7
EN
3.2 CE-declarations of conformity
The CE declarations of conformity for LANCOM routers can be found in the
download area of the LANCOM web site (www.lancom-systems.com).