Land Pride 380-152A User manual

1
Figure 1
Notes
1. This manual is written with the assumption that the
tractor is not supplied with rear remotes or backhoe.
2. This valve kit is designed to operate hydraulic
cylinders.
Assembly Instructions
Initial Preparations
1. Park tractor on a flat surface, place gear shift lever in
park, turn off engine, and remove ignition key.
Valve Assembly
Refer to Figure 1 & Figure 2:
1. Remove hardware “A” used to mount the tractor’s
loader control valve assembly “B”.
2. Bolt Land Pride’s third function valve assembly in
place by positioning mount bracket (#2) under the
tractor’s loader control valve assembly “B”.
3. Reinstall hardware “A” removed in step 1 to secure
Land Pride’s third function valve as shown.
4. Route hydraulic hoses (#12 & #13) under the tractor’s
platform and back towards the rear of the tractor.
37117
A
B
2
1312
11
9
10
Figure 2
Connect Hydraulic Hoses to Power
Beyond Ports
1. Locate and remove hydraulic hose that connects
power beyond port of tractor’s loader valve assembly
to outlet block under the tractor platform.
Refer to Figure 2:
2. Connect hydraulic hose (#12) from “P” port of third
function valve (#10) to the fitting in the power beyond
port of loader valve where hydraulic hose was
removed in step #1 above.
3. Connect hydraulic hose (#13) from “T” port of
third function valve (#10) to fitting in outlet block
where hydraulic hose was removed in step (#1)
4. Secure hoses (#12 & #13) to tractor as needed with
cable ties (#3).
5. Check tractor hydraulic fluid level. If low, add
recommended hydraulic fluid. Refer to your tractor
Operator's Manual for recommended hydraulic fluid
and procedure for checking hydraulic fluid level.
37118
Right-
Hand Side
Left-Hand
Side
Attach to positive (+) post
on the tractor battery
IMPORTANT: Land Pride recommends that your
dealer connects hydraulic hoses (#12 & #13) to your
tractor’s power beyond ports. Improper hook-up
could cause damage to your tractor.
For L3200 & L3800 Kubota Tractors with LA524 Loader
For L3301 & L3901 Kubota Tractors with LA525 Loader
For L4701 Kubota Tractor with LA765 Loader
For L4600 Kubota Tractor with LA764 Loader
380-153M
© Copyright 2014 Printed 10/0 5 /15
Third Function Valve Kit #380-152A
Installation Instructions

2Third Function Valve Kit #380-152A Installation Instructions 380-153M 10/0 5 /15
Land Pride
Assembly Instructions
■
Control Lever Assembly
Refer to Figure 2 on page 1 & Figure 3:
1. Remove existing knob (not shown) from end of
control lever “C”.
2. Install new joystick (#14) over end of control lever “C”
with push buttons facing operator as shown.
3. Tighten set screws (#4) against control lever “C”.
Tighten jam nuts (#5) to secure set screws (#4).
Refer to Figure 2 on page 1:
4. Reference Connection “B”: Connect the two red
wires from the joystick (#14) to one end of wire (#8)
with fuse holder (#16), and connect opposite end of
wire (#8) to the positive (+) post on the tractor battery.
5. Reference Connections “A”: Connect the two black
wires from joystick (#14) to the two wires from the
third function valve (#10).
Refer to Figure 3:
6. Secure wiring with cable ties (#3) as needed.
Cross Beam Mount Assembly
Refer to Figure 2 on page 1 & Figure 4:
1. Orient bulk head mount (#1) as shown and attach it to
the right-hand side of loader crossbeam “D” with
u-bolt (#7) and hex whiz nuts (#6). Tighten hex whiz
nuts to the proper torque.
Refer to Figure 2 on page 1, Figure 4, & Figure 5:
2. Route hydraulic hoses (#9) along the loader arm and
through loader loop bracket “E” to the third function
valve assembly (#10).
3. Connect hoses to quick couplers (#11) on
“A” & “B” ports of valve block (#10).
4. Secure hydraulic hoses (#9) as needed with
cable ties (#3).
Corporate Office: P.O. Box 5060
Salina, Kansas 67402-5060 USA
www.landpride.com‘
Figure 3
Figure 4
Figure 5
37119
Push Buttons
15 4
14
C
3
5
37120
1
9
6
7
D
37121
9
E