Original Tractor Cabs 4421381 Datasheet

HARD TOP SUNSHADE #4421381White / #4421380 Black
FOR:
Dixie Chopper with 2 Post ROPS
ASSEMBLY INSTRUCTIONS - PARTS LIST
! IMPORTANT !
READ THIS MANUAL CAREFULLY AND KEEP FOR FUTURE REFERENCE
! WARNING !
THIS CANOPY WILL NOT PROTECT THE OPERATOR FROM INJURIES CAUSED BY ROLLOVER,
COLLISION, OR OTHER ACCIDENTS
30515817 1

Carton Contents for Hard Top Canopy
PART #
KEY #
QTY.
DESCRIPTION
30516
1
1
Bracket
30504
2
1
Frame
30446
3
2
Brace tube 1/2”
30445
4
2
Brace tube 3/4”
30517
5
2
Clamp
#
1
Plastic Top #11729 White, or #10000 Black
30518
1
Hardware Package (Contents Listed Below)
5144
2
1/4”-20 x 2 3/4” Cap Screw
929
2
1/4”-20 x 3” Cap Screw
926
2
1/4”-20 x 1” Cap Screw
786
2
1/4”-20 x 5/8” Cap Screw
1514
4
1/4” Flat Washer
730
10
1/4”-20 Two Way Lock Nut
906
2
3/8”-16 x 1” HHCS
2908
4
3/8” Flat Washer
790
2
3/8”-16 Two Way Lock Nut
Tools Required:
7/16”, 1/2” & 9/16” wrenches
7/16” & 9/16” sockets with ratchet wrench
Step 1; See Figure 1: Identify all the steel parts using Figure 1 as an example.
Figure 1 2
1
5
4
3
2

Step 2; See Figure 2:
Assemble Bracket (1) and Frame (2).
Assemble the Bracket to the Rear Frame with 3/8” x 1” bolts with 3/8” flat washers over each slot. Add
3/8” lock nuts. Run the nuts most of the way down but do not tighten at this time to allow for later
adjustment.
Figure 2
Step 3; See Figure 3:
Attach the assembly to the roll bar.
Place the clamps over the roll bar and center the bracket. Insert two 1/4” x 2 3/4” bolts up through the
holes. Add 1/4” locknuts and tighten securely.
Figure 3
3
1
2
NOTE: On some
applications
Receivers can
be put on the
other side of the
ROPS for a
better shade
position.

Step 4; See Figure 4:
Insert the front half of the frame into the rear half.
Figure 4
Step 5; See Figure 5:
Install Top.
A. Lay the Plastic Top on the Frame. Place 1/4” washers over two 1/4” x 5/8” bolts. Insert them
inward through the rear holes in the top. Add locknuts.
B. Place 1/4” washers over two 1/4” x 1” bolts. Insert them inward through the front holes in the top
and the tabs welded to the frame. Add locknuts. Tighten the four bolts.
Figure 5
4
2

Step 6; See Figure 6:
Install the Braces and Clamps.
A. Turn the 5/16” x 1/2” bolts out of the weld nuts on the large Brace Tube a few turns. Insert the
small Brace Tubes into the Large Brace Tubes. Place the bolt holes in the small tubes over the 1/4” x
1” bolt and add nuts. Do not tighten at this time.
B. Place Clamps over the roll bar and attach the large Brace Tubes (weld nuts up) to the clamps with
the 1/4” x 3” bolts.
C. Place the clamps as far up as possible to prevent interference when getting on and off of the
machine.
D. Position the top so that it is slightly higher in front and tighten all of the bolts and nuts.
Figure 6
5
3
4
5
! WARNING !
The canopy should be checked for loose bolts or damage before each use to
avoid failure while in use.
NOTE: The flat ends of the Braces can be bent to adjust to the angle of the Clamps on some ROPS.