Landis & Gyr E350 Series 2 User manual

Electricity Meters IEC/MID
Residential
ZCF100Ax/Cx
E350 series 2, 1-phase
User Manual
[Status]
-Date: 20.12.2012
-File name: D000030875 E350 ZCF100Ax Cx 1-ph series 2 User Manual en p.docx
-© Landis+Gyr
D000030875 en q

2/52 [Status] Revision history
© Landis+Gyr D000030875 en q –E350 series 2, 1-phase ZCF100Ax/Cx –User Manual
Revision history
Version
Date
Comments
a
-19.01.2010
-First edition.
-b
-05.05.2010
-New display list items, Combined sum integrated in channel configuration (section
1.6); SW-version presentation updated, Disconnector tamper added, More detailed
explanation of disconnector icon, table of required measuring times updated,
display status messages added, error and status code explanation extended,
addressability added; restriction for SW-version <= M52 added.
"Meter display list" corrected (voltage, current, frequency, power items).
Explanation efficiency registers updated.
Table Instantaneous Values updated.
Display status messages updated.
Meter tools added.
-c-f
-06.09.2010
-Minor formatting and text improvements.
-g
-16.10.2010
-Updating 1.8. Instantaneous values.
-h
-09.12.2010
-Section 5.2.5 Display sequence entirely updated (main and service display).
Declaration of conformity replaced.
-k
-17.03.2011
-Note about restrictions for meters with software versions M51 and M52 added in
section 1.2 "Purpose of use". Section 1.3 "Advice" deleted (integrated into note in
section 1.2).
-m
-01.06.2011
-Section 2.3 "Safety Instructions" expanded with remark, that PE must not be
switched with disconnector and only "useful" tool have to be used; Section 5.2.7
"Error Display" modified; Remark about module data added in section 5.2.9;
Content of section 5.2.12 "Error descriptions E350 Series 1 and Series 2" moved
partly into functional description and partly to section 6.2 "Error Codes": Safety
information about cleaning added in section 6.1 and modified in section 7.2.;
Terminology changes: breaker disconnector, baud rate transmission rate,
baud bps (bits per second); Minor formatting and text improvements.
-n
-20.12.2011
-Section 1.6.3: Adapted to software version M54 (8 measurement channels)
Section 5.2.9: New display item: Disconnector tamper counter.
-p
-24.10.2012
Adapted to software version M55 (DSMR 4.0):
“Introduction” updated.
Figure 3.2 “Basic layout of faceplate” updated.
Section 5.2.4 “Display Definitions” updated.
Section 5.2.5 “Display Sequence” updated.
Section 5.2.6 “Display Check” entering and exiting “Service Display” updated.
Section 5.2.9 “Meter Display List –Available Items with OBIS Codes” updated.
Section 5.4 “Optical Interface” updated (added blocking).
Section 5.5.3 “Readout Status Code (C.5.0)” updated.
New section 5.5.4 “Display status code (C.5.0)” added.
New section 5.6 “Password Lock-out”added.
Section 7.1.1 “Higher Register Resolution” updated.
q
20.12.2012
Section 7.1.2: Note about test time for register test for meter with software version
M54
Section 1.2: Note about restriction for meters with software version M54
Nothing in this document shall be construed as a representation or guarantee in respect of
the performance, quality or durability of the specified product. Landis+Gyr accepts no liability
whatsoever in respect of the specified product under or in relation to this document.
Subject to change without notice.

Table of contents 3/52
D000030875 en q –E350 series 2, 1-phase ZCF100Ax/Cx –User Manual © Landis+Gyr
Table of contents
Revision history ...................................................................................................................................2
Table of contents .................................................................................................................................3
Introduction..........................................................................................................................................5
1Description of Unit......................................................................................................................6
1.1 General View ..........................................................................................................................6
1.2 Purpose of Use .......................................................................................................................6
1.3 Field of Application..................................................................................................................7
1.4 Characteristics ........................................................................................................................8
1.5 Type Designation....................................................................................................................9
1.6 Measuring Principle...............................................................................................................10
1.6.1 Overview..........................................................................................................................10
1.6.2 Signal Generation............................................................................................................10
1.6.3 Signal Processing............................................................................................................11
1.7 Instantaneous Values............................................................................................................12
1.8 Anti-Tampering and Tamper Prevention................................................................................12
1.9 Disconnector.........................................................................................................................13
1.10 Software Tools......................................................................................................................13
2Safety.........................................................................................................................................14
2.1 Safety Information.................................................................................................................14
2.2 Responsibilities.....................................................................................................................14
2.3 Safety Instructions.................................................................................................................15
2.4 Radio Interference.................................................................................................................15
3Mechanical Description............................................................................................................16
3.1 Housing.................................................................................................................................16
3.2 Faceplate..............................................................................................................................17
3.3 Connection Diagrams (examples) .........................................................................................17
3.4 Dimensions...........................................................................................................................18
4Installation/Uninstallation ........................................................................................................20
4.1 Mounting the Meter...............................................................................................................20
4.2 Connecting the Meter............................................................................................................21
4.3 Checking the Connections ....................................................................................................22
4.4 Commissioning and Functional Check ..................................................................................22
4.5 Disconnecting the Meter........................................................................................................23
5Operation ..................................................................................................................................24
5.1 Control Elements...................................................................................................................24
5.1.1 Display Button .................................................................................................................24
5.1.2 Disconnector Button ........................................................................................................24
5.2 Liquid Crystal Display (LCD) .................................................................................................25
5.2.1 Basic Layout....................................................................................................................25
5.2.2 Explanation of LCD Elements..........................................................................................25
5.2.3 Displaying OBIS Codes ...................................................................................................27
5.2.4 Display Definitions...........................................................................................................28
5.2.5 Display Sequence............................................................................................................29
5.2.6 Display Check..................................................................................................................32
5.2.7 Error Display....................................................................................................................32
5.2.8 Text Messages on Display...............................................................................................33
5.2.9 Meter Display List –Available Items with OBIS Codes.....................................................34
5.2.10 Display Status Messages.................................................................................................35

4/52 [Status] Table of contents
© Landis+Gyr D000030875 en q –E350 series 2, 1-phase ZCF100Ax/Cx –User Manual
5.2.11 Energy Efficiency Items in the Meter Display................................................................... 36
5.3 Optical Test Output............................................................................................................... 37
5.4 Optical Interface ................................................................................................................... 37
5.5 Data Readout ....................................................................................................................... 38
5.5.1 IEC 62056-21 Mode C..................................................................................................... 38
5.5.2 Readout Configuration .................................................................................................... 38
5.5.3 Readout Status Code (C.5.0).......................................................................................... 39
5.5.4 Display status code (C.5.0) ............................................................................................. 40
5.5.5 Data Readout Procedure via Optical Interface or AMR Module....................................... 41
5.5.6 Addressability of Meter.................................................................................................... 42
5.6 Password Lock-out............................................................................................................... 42
6Service...................................................................................................................................... 43
6.1 Operating Faults................................................................................................................... 43
6.2 Error Codes.......................................................................................................................... 43
6.2.1 Structure of an Error Code .............................................................................................. 43
6.2.2 Error Code Descriptions.................................................................................................. 44
6.3 Repairing Meters.................................................................................................................. 45
7Maintenance............................................................................................................................. 46
7.1 Meter Testing........................................................................................................................ 46
7.1.1 Higher Register Resolution.............................................................................................. 46
7.1.2 Measuring Times............................................................................................................. 46
7.1.3 Optical Test Outputs........................................................................................................ 47
7.1.4 Connection to a Meter Testing Device............................................................................. 47
7.1.5 Creep Test ...................................................................................................................... 48
7.1.6 Starting Test.................................................................................................................... 48
7.2 Cleaning............................................................................................................................... 48
8Decommissioning and Disposal ............................................................................................. 49
8.1 Decommissioning ................................................................................................................. 49
8.2 Disposal................................................................................................................................ 49
9Annex: Declaration of Conformity .......................................................................................... 50

Description of Unit 5/52
D000030875 en q –E350 series 2, 1-phase ZCF100Ax/Cx –User Manual © Landis+Gyr
Introduction
The present manual applies to the following meter versions:
Single-phase Two-wire network
ZCF100AC and ZCF100AB for active energy (import and export)
ZCF100CC and ZCF100CB for active and reactive energy (import and
export)
For a detailed explanation of the type designation see section 1.5. Some
features of the meter are only available in specific software versions. The
software version can be seen during the start-up of the meter, or, if
configured accordingly, on the display or by readout. In customer
documentation, these items are marked with the numbers of the respective
SW versions as a superscript note, e.g. for the number of channels: 8
(6 [M50…M53]).
The user manual contains all information required for meter applications for
the intended purpose. This includes:
Provision of knowledge concerning characteristics, construction and
knowledge of meters
Information regarding possible dangers, their consequences and
measures to prevent any danger
Details concerning the performance of all work throughout the service
life of the meters (parameterisation, installation, commissioning,
operation, maintenance, shutting down and disposal)
The content of this user manual is intended for technically qualified
personnel of energy supply companies, responsible for system planning,
installation and commissioning, operation, maintenance, decommissioning
and disposal of meters.
The technical data and functional description of the ZCF100 meters can be
found in separate documents:
D000030926 " ZCF100Ax/Cx series 2 Technical Data"
D000028645 "ZxF100Ax/Cx series 2 Functional Description"
Range of validity
Purpose
Target group
Reference documents

6/52 Description of Unit
© Landis+Gyr D000030875 en q –E350 series 2, 1-phase ZCF100Ax/Cx –User Manual
1 Description of Unit
1.1 General View
Fig. 1.1 General view of meter
1.2 Purpose of Use


Restrictions for meters with software versions M51 to M52:
The meters may not be used in networks with significant disturbances in
the frequency range of 2 kHz to 150 kHz since the intended operating
conditions of the meters according to the harmonised standards EN50470-
1 and EN50470-3 assume no significant noise currents and voltages in this
frequency range.
Such significant disturbances occur for instance in large photovoltaic
systems (influence of the inverters with high emissions of extreme
harmonics) and can cause additional errors in the meters, even though the
meters meet all applicable standards and regulations.
Restrictions for meters with software versions M54:
Please follow the required test times for the meter constant or dial test,
mentioned in section 7.1.2. At switching on or off the load (between <0.5A
and >1A) regularly every 20 minutes, an additional error of about 0.1% can
occur. The deviation can be higher, if the load is switched more often. The
meter complies with all specifications. It fulfils all the valid standards and
regulations.
The ZCF100 meters record active and reactive energy consumption in all 1-
phase 2-wire networks. They are directly installed in the supply line by the
energy supply company and are read regularly for billing purposes.
The data is displayed on an LCD and is also available via optical interface
and with an AMR Module via CS, PLC modem, GSM/GPRS modem or
ethernet. When provided with transmission contacts, the meters can also
be used as transmission contact meters for telemetering. The rates can be
controlled externally with control inputs (on the AMR Module).

Description of Unit 7/52
D000030875 en q –E350 series 2, 1-phase ZCF100Ax/Cx –User Manual © Landis+Gyr
With an AMR module, the meters can also be used to record counting
pulses of other physical media (e. g. water or gas volumes) or to directly
transmit values recorded by other measuring devices.
Any other application of these meters is regarded as abuse.
1.3 Field of Application
The basic version provides energy registers for tariffication, a red test diode
for active or reactive energy, an optical interface for meter reading and an
interface for various communication forms. This interface is protected against
fraud and is independent of the module suppliers. The exchangeable AMR
Module is situated outside the calibration liability. The functionality of this
meter is suitable for smaller consumers, e.g. for households.
The function of the disconnector is customer specific and is defined by the
communication module. Possible uses: anti-tampering (e.g. disconnection
in case of tampering with magnets), load limitation (fuse control), remote
disconnect (e.g. in case of change of tenant), prepayment. The status of
the disconnector is displayed on the meter, but the disconnector is
controlled by the communication module. If you need detailed information
on the functionality of your disconnector, please consult the user manual of
the communication module installed.
The basic series can be extended with various AMR Modules for additional
functions and communications:
Multirate import/export with external rate control
S0 pulse output
Communication via PLC, GSM/GPRS, or other media.
The meter functions which can be used in the system are defined by the
module (e.g. a 2 rate module is not able to control 6 rates in the meter).
Therefore, meter and module together define the functionality range which
can be used.
As the meter has a wide range of configuration possibilities, a specific
behaviour can in some cases differ from the description below.
The meters can be parameterised, i.e. specific parameters can be set with
software, so that the meters can be supplied according to the specific wishes
of the relevant utility.

Retroactive modification of the parameters is not possible.
The parameters stored in the meter are protected against unauthorised
overwriting.
Details about parameter settings can be found in the functional description.
Basic series
Disconnector
(ZCF100xB only)
Extensions
Parameterisation

8/52 Description of Unit
© Landis+Gyr D000030875 en q –E350 series 2, 1-phase ZCF100Ax/Cx –User Manual
1.4 Characteristics
The meters have the following characteristics:
Recording of active and reactive energy in all 4 quadrants (ZCF100Cx)
or recording of active energy imported and exported (ZCF100Ax) with
up to 6 rates
Rate control performed via AMR module
Data display on LCD
Measuring elements in DFS (Direct Field Sensor) technology with
excellent measuring characteristics, including flat load curve, high
stability and good protection against interference.
Active energy measurement accuracy: Classes 1 and 2 (IEC62053-21)
and MID accuracy classes A and B (EN50470-3)
Reactive energy measurement accuracy: Class 2 (IEC62053-23)
Wide range measurement from starting current to maximum current
Serial interface with optical input/output for automatic readout of data
on the spot and for service functions
AMR interface (connection to communication module) for meter
reading and tariff control according to IEC 62056-21
Storage of event information (e.g. power outages)
Installation aids (e.g. phase voltages and direction of energy)
-Presence of phase voltage (voltage value is displayed)
-Visual output (creep indicator) on LCD
-Display of energy direction
-Power indication

Description of Unit 9/52
D000030875 en q –E350 series 2, 1-phase ZCF100Ax/Cx –User Manual © Landis+Gyr
1.5 Type Designation
1 phase 2 wire network
Network Type
Connection Type
ZCF 1
Additional Functionality
C
A
ZCF
Meter with communication interface
Direct connection1
Accuracy Class active energy
20 Class 1 (IEC); B (MID)
10
10
Class 2 (IEC); A (MID)
BMeter with communication interface and disconnector
e
Rates 1 rate
2 rates
e
dMultirate (up to 6 rates)t
F
Measured Quantities
Active energy
Active and reactive energy
A
C
Anti-tampering
-No anti-tampering
FAnti-tampering
Version
s2 Series 2
s2B
The "e" for the 1-rate version can be skipped in some versions.

The AMR Module is not part of this type designation, since it is a complete
unit in itself. Users can change it without opening the calibration seal.

10/52 Description of Unit
© Landis+Gyr D000030875 en q –E350 series 2, 1-phase ZCF100Ax/Cx –User Manual
1.6 Measuring Principle
1.6.1 Overview
The main meter inputs are:
Phase connection (L1) and neutral for
-energy measurement
-power supply of the meter
-PLC communication with communication modules
Display button
Disconnector button (only if meter equipped with disconnector)
The main meter outputs (partly also inputs) are:
LCD to display measured values and the corresponding OBIS code
Optical test outputs (red, for active or for reactive energy)
Optical interface for automatic data readout on site by means of a
suitable HHT (Hand Held Terminal) (also input)
Secured AMR Interface for automatic data readout through an AMR
module, e.g. E35C module, with a PLC, GSM/GPRS, Ethernet or other
medium (also input).
The supply voltage for the meter electronics is taken from the Single-phase
system. A voltage monitor guarantees a safety data storage in the event of
a mains voltage failure and a correct start-up after the return of the voltage.
A non-volatile memory (EEPROM) contains the parameter set of the meter
and secures the stored measurements against loss due to power failure.
1.6.2 Signal Generation
The measuring element, a DFS (Direct Field Sensor), registers the phase
current with the magnetic field of the current loop and the phase voltage
over a resistor divider. The analog/digital converters transform both signals
into digital voltage and current data. This data is then multiplied by a digital
multiplier to produce an energy proportional value which is then transferred
into the energy registers (rate-dependent).
The microprocessor generates pulses for the test diode from the digital
value according to the meter constant R.
Inputs
Outputs
Power supply
Memory

Description of Unit 11/52
D000030875 en q –E350 series 2, 1-phase ZCF100Ax/Cx –User Manual © Landis+Gyr
1.6.3 Signal Processing
The meter records active and reactive energy and can distinguish between
energy import and export in up to 6 rates (depending on configuration).
Calibration data is stored during the final testing of the meter.
The microprocessor compares the measured power with the minimum
starting power. The signals are only passed on if the minimum starting
power is exceeded.
The following energy values can be measured and stored in the registers:
Active energy A
Reactive energy R
Apparent energy S
+A and +R are the imported measured active and reactive energy, –A and
–R the exported measured active and reactive energy.
The combined values are the sum or the difference of the absolute values
of +A and –A or +R and –R.
The measurement of single quadrants can be configured too.
Energy type: kWh, kVarh or kVah
Direction: Import, export, ± reactive
Instantaneous Values: Voltage, current, frequency, power factor
There are 8 (or 6 [M50…M53]) independent measurement channels. One of the
measured quantities can be assigned to each of this register.
The measurement channels 1 to 6 have 6 rated registers and 1 total each,
channel 7 and 8 have only 1 total register. 44 registers are therefore avail-
able in total.
All registers work internally with 9 digits. The internal magnitude is Wh
(Watt-Hours). They cannot be reset. At 999999999, a rollover to 0 takes
place. The display and readout formats vary from the internal format.
The meter is designed for up to 6 rates. The assignment of the rate regis-
ters is done by means of parameterisation and is shown on the faceplate.
Rate control is performed by the external module.
With up to 2 rates, the rate switching is operated by the AMR Module directly
or by control inputs. The rate switching for more than 2 rates can be oper-
ated only by the AMR module.
The reactive energy (±Rc, ±Ri) is allocated to the 4 quadrants as follows:
+R
+ kWh
- kWh
-R
+Ri+Rc
-Rc-Ri
+A ImportExport -A
- kvarh - kvarh
+ kvarh+ kvarh
Quadrant II Quadrant I
Quadrant IVQuadrant III
Fig. 1.2 4-quadrant measurement
Calibration
Start detection
Measured quantities
Measurement
channels
Energy registers
Rates
Rate control
4-quadrant
measurement

12/52 Description of Unit
© Landis+Gyr D000030875 en q –E350 series 2, 1-phase ZCF100Ax/Cx –User Manual
A measured quantity can be assigned by parameterisation to each of the 8
available channels. The following table shows some of the most common
measured quantities used:
Value
OBIS
Direction
Quadrant(s)
Unit
+A
1.8.0
Import
I + IV
kWh
–A
2.8.0
Export
II + III
kWh
|+A| + |–A|
15.8.0
Combined sum
I + II + III + IV
kWh
+R
3.8.0
Import
I + II
kVarh
+R
5.8.0
Import
I
kVarh
+R
6.8.0
Import
II
kVarh
–R
4.8.0
Export
III + IV
kVarh
1.7 Instantaneous Values
Instantaneous values are updated every second.
The following instantaneous values are available:
Measured value
Resolution
Start value
Max. value
Voltages L1, L2, L3
-1 V
-170 V
-440 V
-Currents I1, I2, I3
-0.01 A
-0.2 A
-120 A
-Frequency
-0.1 Hz
-47 Hz
-53 Hz
-Power Factor
-0.1
--1
-1
-Power
-0.01 kW or 0.001
kW 1)
-I > 0.075 Ib
-Imax
1) Depending on meter configuration (from SW version M55 onwards).
If no value is available "---" can be shown (e.g. if in creep or value below
start value).
1.8 Anti-Tampering and Tamper Prevention
E350 meters feature four optional anti-tampering functions:
Detection of terminal cover opening
Detection of DC magnetic field
Sealable access lock to voltage connections
Detection of disconnector tampering (disconnector meters only)
Channel configuration

Description of Unit 13/52
D000030875 en q –E350 series 2, 1-phase ZCF100Ax/Cx –User Manual © Landis+Gyr
1.9 Disconnector
The ZxC100xB version of the E350 meter is equipped with a disconnector
which is controlled via the communication module. Various functions can be
implemented:
disconnection if credit has been used up
change to minimum power mode if credit has been used up
disconnection, if maximum power has been exceeded over a specified
time
others
The disconnector can either be controlled via the AMR module or manually
with the disconnector button on the meter’s terminal cover (if parameterised
accordingly, see also section 5.1.2 "Disconnector Button").
1.10 Software Tools
Landis+Gyr meters are provided with optimum support by suitable software
tools during all phases of their life cycle:
The Landis+Gyr MAP110 service tool for customers is used for the test
and installation of meters and for servicing work on the spot.
For the list of functions of MAP110, please see MAP-documentation and
the E350 Functional Description.

14/52 Safety
© Landis+Gyr D000030875 en q –E350 series 2, 1-phase ZCF100Ax/Cx –User Manual
2 Safety This section describes the safety information used in this manual, outlines
the responsibilities and lists the safety instructions to be observed.
2.1 Safety Information
Attention is drawn to dangers and their level (severity and probability) in
this user manual in the following way:
Warning
Used to indicate a dangerous situation that could cause bodily injury or
death.
Caution
Used to indicate a situation/ action that could result in material damage or
loss of data.

Note
Used to indicate general guidelines and other useful information.
All safety information also describes the type and source of the danger, its
possible consequences and measures to counteract the danger.
2.2 Responsibilities
The owner of the meters is responsible that all persons engaged on work
with meters:
1. Are competent and qualified in accordance with national regulations
(see ISSA "Guideline for Assessing the Competence of Electrically
Skilled Persons").
2. Have read and understood the relevant sections of the user manual.
3. Strictly observe the safety instructions (according to section 2.3) and
the operating information in the individual sections.
In particular, the owner of the meters bears responsibility
for the protection of persons,
prevention of material damage
and the training of personnel.
Landis+Gyr AG provides training courses for this purpose on specific
equipment; please contact the relevant agent if interested.

Safety 15/52
D000030875 en q –E350 series 2, 1-phase ZCF100Ax/Cx –User Manual © Landis+Gyr
2.3 Safety Instructions
The following safety instructions must be observed at all times:
The meter connections must not be under voltage during installation or
when opening. Contact with live parts is dangerous to life. The relevant
main fuse should therefore be removed and kept in a safe place until
the work is completed, so that other persons cannot replace it
unnoticed.
Local safety regulations must be observed.
Protection earth connection must not be switched with the
disconnector.
Only "useful" tools have to be used. This means a screw driver has to
have the correct size for the screws and the metallic part of a screw
driver has to be insulated.
The meters must be held securely during installation. They can cause
injuries if dropped.
Meters which have fallen, must not be installed, even if no damage is
apparent, but must be returned for testing to the service and repair
department responsible (or the manufacturer). Internal damage can
result in functional disorders or short-circuits.
The meters must on no account be cleaned with running water or with
compressed air devices. Water penetrating can cause short-circuits.
2.4 Radio Interference

Possible radio interference in residential environments
This meter is normally a class B product. In combination with some
communication modules, it can become a Class A product. In a domestic
environment, this may then cause radio interference, in which case the user
may be required to take adequate measures.

16/52 Mechanical Description
© Landis+Gyr D000030875 en q –E350 series 2, 1-phase ZCF100Ax/Cx –User Manual
3 Mechanical Description
3.1 Housing The internal construction of the meter will not be described here, as the
meter is sealed after calibration and verification.
5
2
43
1
7
8
9
10
11
6
Fig. 3.1 Front view of meter
1 Suspension hanger in upper position
2 Suspension hanger in lower position
3 Display button
4 LCD
5 Optical interface
6 Front cover (faceplate with laser marking, for details see Fig. 3.2)
7 Test diode (red)
8 AMR Module compartment
9 Terminal block cover
10 Screw with sealing point (manufacturer or utility seal)
11 Disconnector button
A terminal block with all connecting terminals is located under the terminal
cover. On the terminal cover, a sealing point for a utility seal prevents
unauthorised access to the phase connections and therefore help to avoid
unrecorded power consumption.

Mechanical Description 17/52
D000030875 en q –E350 series 2, 1-phase ZCF100Ax/Cx –User Manual © Landis+Gyr
3.2 Faceplate
The faceplate (laser marking on front cover) shows customer-specific meter
information.
Fig. 3.2 Basic layout of faceplate
1 Meter data
2 Approval symbol, CE conformity symbol
3 Customer No. / Barcode / Ownership designation
4 Double protection insulation symbol
5 Active rate
The display button and the display are fully described in section 5.
3.3 Connection Diagrams (examples)

Where to find relevant diagrams
The diagrams relevant for the installation are shown on the meter’s
faceplate or specified otherwise (e.g. inserted in the terminal cover).
Fig. 3.3 Connection diagram ZCF100AC
Fig. 3.4 Connection diagram ZCF100AB with disconnector

18/52 Mechanical Description
© Landis+Gyr D000030875 en q –E350 series 2, 1-phase ZCF100Ax/Cx –User Manual
3.4 Dimensions
The meter is only available with an extended terminal cover (see Fig. 3.5).
Fig. 3.5 Meter dimensions
The extended terminal cover offers increased safety since the phase and
neutral connecting wires are protected under the terminal cover.
The suspension triangle complies with DIN standards.
Fig. 3.6 Meter without terminal block cover

Mechanical Description 19/52
D000030875 en q –E350 series 2, 1-phase ZCF100Ax/Cx –User Manual © Landis+Gyr
Terminals are available with an opening diameter of 8.5 mm and 9.5 mm.
Terminals with opening diameter of 8.5 mm and 9.5 mm have the same
position on the terminal block.
Fig. 3.7 Terminal layout and dimensions

20/52 Installation/Uninstallation
© Landis+Gyr D000030875 en q –E350 series 2, 1-phase ZCF100Ax/Cx –User Manual
4 Installation/Uninstallation
4.1 Mounting the Meter
The meter should be mounted as follows on the meter board or similar
device provided for this purpose (see also section 3.4 "Dimensions"):
1. Find the correct position for the meter. Ensure there are no wires
underneath the holes to be drilled.
2. Define the desired form of fixing (open or covered meter mounting).
3. Ensure with a phase tester or universal measuring instrument that the
connecting wires are not live.
105 mm
179 mm for open mounting
52.5 mm
155 mm for covered mounting
Fig. 4.1 Drilling plan
4. Mark the three fixing points (suspension triangle as shown in the
drilling plan Fig. 4.1) on the mounting surface provided.
5. Drill the three holes.
6. Unscrew the meter terminal cover.
7. For open meter mounting, insert the meter suspension eyelet –this is
supplied in the terminal cover –into the corresponding opening at the
rear side of the meter until the suspension eyelet engages (see Fig. 4.2).
Fig. 4.2 Meter suspension eyelet
8. Fit the meter with 3 fixing screws on the mounting surface provided.