Landmann BALL 'O FIRE User manual

PLEASE READ ALL RULES FOR SAFE
OPERATION BEFORE ASSEMBLY AND
HELPFUL HINTS BEFORE USE.
ASSEMBLY INSTRUCTIONS
MODEL 28925
Congratulations on your purchase of the Ball 'O Fire! At Landmann USA,
we strive to provide you with an easy to use, easy to assemble product.
However, in the unlikely event your package should have a missing or
defective part, please contact us at:
[e-mail]
-OR-
1-800-321-3473 M-F 8-5 Eastern Time
Proof of purchase may be required. Thank you!
Landmann USA
Cartersville, GA 30120
www.landmann-usa.com
Made in China
© 2007 Landmann USA
BALL 'O FIRE™
MODEL 28925
!
PAGE 1
VER. 1, 8/30/2007
• FOR OUTDOOR USE ONLY!
• USE ONLY ON BRICK, CONCRETE, STONE OR OTHER MASONRY
SURFACES!
• DO NOT USE ON LAWNS, WOODEN DECKS OR ASPHALT!
• THE BALL 'O FIRE MUST BE PLACED ON A LEVEL SURFACE.
• DO NOT USE WITHOUT FIREBOWL, THE FIREBOWL MUST BE
USED AT ALL TIMES!
• FIREWOOD MUST BE KEPT WITHIN THE BOUNDARIES OF THE
FIREBOWL.
• FIREWOOD MUST NOT BE ALLOWED TO TOUCH ANY PART OF
THE SCREEN.
• FOR LONGER LIFE, KEEP FIRES TO A RESPECTABLE SIZE, DO
NOT OVERLOAD.
• DO NOT BURN LEAVES OR GARBAGE IN THE BALL 'O FIRE.
• KEEP THE BALL 'O FIRE AWAY FROM BUILDINGS, FLAMMABLE
ITEMS AND VEHICLES.
• THE BALL 'O FIRE IS FOR ADULT USE ONLY.
• DO NOT LEAVE UNATTENDED AT ANY TIME WHILE IN USE.
• KEEP SPARK GUARD DOOR CLOSED WHILE IN USE.
• DO NOT USE IN WINDY CONDITIONS!
• NEVER USE GASOLINE, ALCOHOL OR VOLATILE FLUIDS TO
START FIRES.
• NEVER USE UNDER LOW HANGING TREE BRANCHES, TRELLIS,
OVERHANGS OF ANY KIND INCLUDING COVERED PORCHES.
• USE CAUTION WHEN TENDING THE FIRE, AS SURFACES WILL
BE HOT WHILE IN USE.
• USE MITTENS OR POKER IF NECESSARY TO OPEN THE SPARK
GUARD DOOR.
• BEFORE EACH USE MAKE SURE THE BALL 'O FIRE IS IN GOOD
WORKING CONDITION.
• USE CAUTION AFTER THE FIRE HAS BEEN EXTINGUISHED,
SURFACES WILL REMAIN HOT FOR SOME TIME.
• USE THE COVER ONLY AFTER THE BALL 'O FIRE HAS
COMPLETELY COOLED.
READ FIRST!
RULES FOR SAFE OPERATION
!

PARTS LIST:
When unpacking the Ball 'O Fire from the carton, make sure you find and become familiar with all the pieces listed below:
VER. 1, 8/22/07
C
(3) LEGS
P
(26)
M6 x 13
BOLTS
(1) COVER
(1) CENTER RING
E F G
A B
(3) BOTTOM
SCREEN
SECTIONS
(3) BOTTOM
SCREEN
SECTIONS
(1) LEFT FIXED
TOP SECTION
(1) CENTER FIXED
TOP SECTION
(1) RIGHT FIXED
TOP SECTION
HJK
(1) LEFT DOOR
SECTION
(1) CENTER DOOR
SECTION
(1) RIGHT DOOR
SECTION
L
M N
(1) CONNECTING
RING
(1) CONNECTING
RING W/ HANDLE
(2) BOWL
HANDLES
Q
O
(1) BOWL
UT
S
(6)
M6 x 10
BOLTS
(6)
M6 x 20
BOLTS
R
(6)
M6 x 25
BOLTS
X
(6)
M6
CAP NUTS
V
(2)
M6 x 40
BOLTS
Y
(2)
LOCK
WASHERS
W
(48)
M6
HEXNUTS
PAGE 2
BALL 'O FIRE™
IF YOU HAVE MISSING
OR DEFECTIVE PARTS,
PLEASE CALL CUSTOMER
SERVICE AT 1-877-347-4557
FOR OUTDOOR
USE ONLY
!

STEP 2
Assemble (1) pc
screen section [A]
to the screens using
(2) M6 x 13 bolts,
(1) M6 x 25 bolt and
(3) M6 hexnuts as
shown. Assemble
the M6 x 25 bolt
where shown. Only
finger tighten at this
time.
STEP 4
Assemble the (3)
legs [D] to the
screen bowl using
(6) M6 hexnuts.
Securely tighten the
bolts.
STEP 3
Following the same
instructions in steps
1 and 2, continue to
alternate and
assemble the
remaining screen
sections [A,B] until
the screen bottom
is formed.
PAGE 3
BALL 'O FIRE™
STEP 1
Find (1) pc each of
the bottom screen
sections [A,B].
Assemble together
using (2) M6 x 13
bolts, (1) M6 x 25
bolt and (3) M6
hexnuts as shown.
Assemble the
M6 x 25 bolt where
shown. Only finger
tighten at this time.
ASSEMBLY INSTRUCTIONS:
D
A
B
A
BA
B
A
BA
M6 x 25 bolt /
hexnut here
X
X
M6 x 13 bolt /
hexnut on the
inside
M6 x 13 bolt /
hexnut on the
inside
A
B
M6 x 13 bolt /
hexnut on the inside XM6 x 25 bolt /
hexnut here
M6 x 13 bolt /
hexnut on the
inside
STEP 5
Find the center ring
[C] and remove the
pre-assembled
M6 x 20 bolts and
M6 hexnuts.
Carefully place the
center ring on the
screen sections
aligning the holes
with the center ring.
Assemble with the
(6) M6 x 20 bolts
and M6 hexnuts.
Securely tighten the
bolts.
STEP 6
Assemble screen
sections [E,F,G]
together with (6)
M6 x 10 bolts and
(6) M6 cap nuts.
Assemble with the
cap nuts on the
outside. Tighten
bolts and cap nuts
securely.
E
F
G
STEP 7
Assemble connecting
ring [L] to the screen
sections using (4)
M6 x 13 bolts and
M6 hexnuts. Tighten
securely.
C
L
HJ
K
STEP 9
Assemble connecting
ring with handle [M]
to the screen
sections using (4)
M6 x 13 bolts and
M6 hexnuts. Tighten
securely.
Make sure cap nuts
are assembled on the
outside (STEP 6).
EF
G
STEP 8
Assemble screen
sections [H,J,K]
together with
(6) M6 x 13 bolts
and (6) M6 hexnuts.
Securely tighten the
bolts.
H
J
K
M
IMPORTANT!
IMPORTANT!
IMPORTANT!
X
X
X
X

• ADDING SAND TO THE BOTTOM OF
FIREBOWL HELPS PROTECT AGAINST
THE CORROSIVE NATURE OF THE ASHES
AND WILL EXTEND THE LIFE OF
THE FIREBOWL.
• IF YOU ARE NOT GOING TO USE THE
BALL 'O FIRE FOR A LONG PERIOD
OF TIME, STORE AWAY OUT OF THE
WEATHER OR USE THE COVER TO KEEP
DRY.
• DO NOT LET FIREBOWL FILL WITH
WATER.
• DO NOT DUMP ASHES WHERE THEY
COULD START A FIRE.
• DISPOSE OF ASHES IN PROPER
RECEPTACLE ONLY AFTER ASHES HAVE
COOLED.
HELPFUL HINTS
STEP 10
Assemble the fixed
screen sections
[E,F,G] to the center
ring using (2) M6 x
13 bolts and hexnuts.
Tighten securely.
BALL 'O FIRE™
ASSEMBLY INSTRUCTIONS:
STEP 12
Assemble door
screen section
[H,J,K] to the pivot
pins as shown.
Squeeze the ends of
the door together if
necessary and insert
into the pins.
Assemble the door
with (2) M6 x 40
bolts, lock washers
and M6 hexnuts.
Assemble as shown.
Place the firebowl on
the inside and onto
the M6 x 25 bolts.
The Ball 'O Fire is
ready for use.
Enjoy!
STEP 11
Assemble the bowl
handles [N] to the
bowl [O] using (4)
M6 hexnuts.
Tighten securely.
PAGE 4
IF YOU HAVE QUESTIONS OR
TROUBLE WITH ASSEMBLY,
PLEASE CALL 1-877-347-4557
FOR ASSISTANCE.
WARNING!
!
DO NOT USE WITHOUT FIREBOWL,
THE FIREBOWL MUST BE USED AT
ALL TIMES. KEEP FIREWOOD
WITHIN THE BOUNDARIES OF THE
FIREBOWL. DO NOT PILE WOOD ON
ANY SCREEN PART. FIREWOOD
MUST NOT BE ALLOWED TO TOUCH
ANY PART OF THE SCREEN. FOR
LONGER PRODUCT LIFE, KEEP
FIRES TO A RESPECTABLE SIZE,
DO NOT OVERLOAD.
M6 hexnut
M6 x 13 bolt
M6 x 40 bolt
M6 hexnut
Lock washer