Landscape Forms Connect 2.0 User manual

Installation Guide
Connect 2.0 Shelter, wiring guide for hard-wired unit
www.landscapeforms.com Ph: 800.521.2546
Date: December 17, 2018
Page 1 of 4
ASSEMBLEWITHCARE! Pangard IIPolyesterPowdercoat isastrong,long‐lasting
finish.Toprotectthisfinishduringassembly,placeunwrappedpowdercoated partson
packagingfoamorothernon‐marringsurface.Donotplaceorslidepowdercoated
partsonconcreteorotherhardortexturedsurface– thiswilldamagethefinishcausing
rusttooccur.Usetouch‐uppaintonanygougesinthefinishcausedbyassemblytools.
1. Anchorkitinstallation
2. Frameassembly
3. Roofassembly
4. Wallglassassembly
5. Wiringconnections
Orderofoperations:
ToolsRequired
•wiringtools
•3/32”hexkey
•3/16”hexkey
•5/16”Socketwrench
•Flatheadscrewdriveror¼”socketwrench
Includedcomponents:
•Uplights,withwiringharnesses,pre‐installedinfronthorizontalbeam
•Downlights,withwiringharnessandconnectors,oneperrafter
•Wayfindinglights,withwiringharness,twoperunit
•SJOOWcord,blackouterinsulation,16gauge,3wire,150inlength
WAYFINDING
LIGHT
Fig.1– lightingcomponentlocations
UPLIGHTS,
PRE‐INSTALLED
DOWNLIGHT
DRIVER
PLATE
CONDUIT
LOCATION
RIGHT
REAR
POST
RIGHT
FRONT
POST

Installation Guide www.landscapeforms.com Ph: 800.521.2546
Page 2 of 4
INSTALLATION:
1. Run3‐wire16gaugecordfromrearrightuppercorner,throughgrommetandinto
accesshole,downtherightverticalposttoline‐involtagewiring.Donotconnectto
line‐involtage.SeeFigs.2and3.
2. Firstrafterdownlight:makeconnectionatfronthorizontaltoquickdisconnect.Run
16gaugejacketedcordfromrearrightuppercorneralongbottomofrafter.Push
cordthroughgrommet,alongwithrafterlightconnection.SeeFig.4.Usinga3/32”
hexkey,attachdownlighttorafterusing(6)#8‐32x5/16socketbuttonheadcap
screws,locatedinhardwarepack#62599.Donotovertightenscrews.
3. Installremainingrafterdownlights:makeconnectiontoquickdisconnects.Push
connectionthroughnearestgrommetonfronthorizontalbeam.Attachdownlight
torafter,seeFig.4.
4. Unusedgrommetsonrearhorizontalbeamcanbesealedwithclearorblacksilicone
(suppliedbyothers).
5. Installleftandrightsiderafterskins,withthesharperangleoftheskintowardthe
frontoftherafter.SeeFig.5.Rafterskinshaveabossonthebottomflangethat
hooksintothedownlight,seeFig.5.Hookthebottomoftheskinintopositionand
thenrotatethetopofskinuptotherafterbeam.Usinga3/16”hexkey,install(2)
¼‐20x¾”socketheadcapscrews,locatedinhardwarepack#62599atthetop.
Tightenuntilgapbetweenlightandrafterskinisgoneandrafterskindoesnot
rattle.Donotovertightenscrews.
6. Wayfindinglights:Runwiringharnessupthroughfrontverticalpost.Onthefront
leftsideoftheunit,removetheaccesscoveronthefronthorizontalbeam.Make
connectionfromthewiringharnesstothequickdisconnectlocatedinthebeam.
SecureLEDtofrontverticalpost,using(4)8‐32x½”hexheadmachinescrewswith
externaltoothlockwasher,locatedinhardwarepack#62810,seeFig.6.Beforefinal
tighteningofscrews,ensureonlythelensfromthelightisshowingthroughthe
frontopening.Repeatforoppositeside.Installcoverplates,using(2)¼‐20x½”
socketheadcapscrews,locatedinhardwarepack#62607,seeFig.7.
7. Driverplateassembly:Attachdriverplatetofronthorizontalbeam,inthefront
rightaccesslocation,seeFig.8.
8. MakeconnectionstoPDMaslabeled:Uplight,Wayfinding(x2),Downlight,seeFigs
9and10.Makeconnectionstoterminalblockfromthe16gaugejacketedcord.
Attachgroundingpigtailtofronthorizontalbeam,seeFig.8.Tightencordgrip.
Replaceaccesscover.
9. Connect3‐wire16gaugecordtoline‐involtagewiringandinstallcover.
Connect 2.0 Shelter, wiring guide for hard-wired unit Date: December 17, 2018
FRONT
Fig.2–install16gaugejacketedcord
RIGHT
REARPOST
Fig.3 – jacketedcordinstalldetail,rearrightpost
16GAJACKETEDCORD
RUNALONGBOTTOM
OFRAFTER
DOWNLIGHT
GROMMET
INTERIORACCESSHOLE
TOVERTICALPOST

Installation Guide www.landscapeforms.com Ph: 800.521.2546
Page 3 of 4
Connect 2.0 Shelter, wiring guide for hard-wired unit Date: December 17, 2018
Fig.4–installrafterlight
QUICK
DISCONNECT
DOWNLIGHT
FRONT
HORIZONTAL
BEAM
RAFTER
GROMMET
ATTACHMENT
POINT(3PERSIDE)
Fig.5–installrafterskins
RAFTER
SKIN
HOOKSINTO
DOWNLIGHT
1/4‐20x3/4”SHCS
(2)PERSIDE
WIRINGHARNESS
FORWAYFINDING
LIGHT
Fig.6–Installwayfindinglights
WAYFINDING
LIGHT
ASSEMBLY
(4)8‐32x½HEXHD
MACHINESCREWSWITH
LOCKTOOTHWASHERS
COVER
PLATE
Fig.7–Installwayfinding
lightcoverplate
(2)¼‐20x½
SOCKET
HEAD
CAPSCREW
Fig.5a–Installrafterskin

Installation Guide www.landscapeforms.com Ph: 800.521.2546
Page 4 of 4
Connect 2.0 Shelter, wiring guide for hard-wired unit Date: December 17, 2018
GROUNDING
PIGTAIL
Fig.8–Installdriverplateassembly,frontrightaccesshole
16gaJACKETED
CORD,CONNECT
TOTERMINAL
BLOCK
(2)¼‐20x½SOCKET
HEADCAPSCREWS
Fig.9– wiringconnections
Fig.10– wiringdiagram