Lang AGC User manual

Lang Manufacturing Company 6500 Merrill Creek Parkway Everett, WA 98203
Part Number: 60801- Phone: [phone] Fax: [phone] © Copyright 1998
WWW.LANGWORLD.COM
Installation
Operation
Maintenance
Troubleshooting
Model: AGC
Add-on Clamshell® Hood

2
THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE. READ,
UNDERSTAND AND FOLLOW THE INSTRUCTIONS AND WARNINGS CONTAINED
IN THIS MANUAL.
FOR YOUR SAFETY
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND
LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
POST IN A PROMINENT LOCATION
INSTRUCTIONS TO BE FOLLOWED IN THE EVENT USER SMELLS GAS. THIS
INFORMATION SHALL BE OBTAINED BY CONSULTING YOUR LOCAL GAS
SUPPLIER. AS A MINIMUM, TURN OFF THE GAS AND CALL YOUR GAS
COMPANY AND YOUR AUTHORIZED SERVICE AGENT. EVACUATE ALL
PERSONNEL FROM THE AREA.
WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE
OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH.
READ THE INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS
THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT.
Model #: Purchased From:
Serial #: Location:
Date Purchased: Date Installed:
Purchase Order #: For Service, Call:

3
TABLE OF CONTENTS
CHAPTER PAGE
1. READ FIRST ................................................................................................................. 4
2. EQUIPMENT DESCRIPTION........................................................................................ 6
3. UNPACKING ................................................................................................................. 7
4. INSTALLATION ............................................................................................................. 8
5. INITIAL START-UP ....................................................................................................... 10
6. OPERATION ................................................................................................................. 11
7. SEQUENCE OF OPERATION ..................................................................................... 12
8. CLEANING & MAINTENANCE PROCEDURES .......................................................... 13
9. TROUBLESHOOTING .................................................................................................. 14
10. PARTS LISTS................................................................................................................ 16
11. WIRING DIAGRAMS ..................................................................................................... 18
12. WARRANTY .................................................................................................................. 19

4
IMPORTANT READ FIRST IMPORTANT
NOTICE: If the Clamshell® is to be attached to a griddle/ charbroiler in the
field – it is recommended to complete the installation of mounting adapter
before un-crating the Clamshell®.
CAUTION: UNIT IS EXTREMELY HEAVY. FOR SAFE HANDLING, INSTALLER SHOULD
OBTAIN HELP AS NEEDED, OR EMPLOY APPROPRIATE MATERIALS
HANDLING EQUIPMENT (SUCH AS A FORKLIFT, DOLLY, OR PALLET
JACK) TO REMOVE THE UNIT FROM THE SKID AND MOVE IT TO THE
PLACE OF INSTALLATION.
WARNING: INSTALLATION OF THE UNIT MUST BE DONE BY PERSONNEL QUALIFIED
TO WORK WITH ELECTRICITY AND PLUMBING. IMPROPER
INSTALLATION CAN CAUSE INJURY TO PERSONNEL AND/OR DAMAGE
TO EQUIPMENT. UNIT MUST BE INSTALLED IN ACCORDANCE WITH ALL
APPLICABLE CODES.
CAUTION: SHIPPING STRAPS ARE UNDER TENSION AND CAN SNAP BACK WHEN
CUT.
DANGER: DO NOT REMOVE THE MOUNTING NUTS OFF OF THE MOUNTING PLATE
STUDS WHILE THE UNIT IS IN THE LOWERED POSITION. THE
STANCHION BACK IS UNDER TENSION AND CAN CAUSE BODILY INJURY.
NOTICE: The data plate is located on the inside surface of the hood wrap. The
Clamshell® voltage, wattage, serial number, clearance and gas
specifications are on the data plate. This information should be carefully
read and understood before proceeding with the installation.
NOTICE: This unit is approved to be installed only on equipment which meets NSF
standards, and for which the adapter kit is provided.
WARNING: BEFORE LIGHTING, USE A SOAP AND WATER SOLUTION TO TEST ALL
JOINTS FOR GAS LEAKS.
NOTICE: The installation of any components such as a vent hood, grease extractors,
fire extinguisher systems, must conform to their applicable National, State
and locally recognized installation standards.
WARNING: DURING INITIAL USE, OR USE AFTER SERVICE, IF THE PILOT DOES NOT
IGNITE ON FIRST TRY THE MAIN GAS VALVE MUST BE TURNED OFF FOR
AT LEAST FIVE MINUTES.
CAUTION: ALWAYS KEEP THE AREA NEAR THE APPLIANCE FREE FROM
COMBUSTIBLE MATERIALS.
CAUTION: KEEP FLOOR IN FRONT OF EQUIPMENT CLEAN AND DRY. IF SPILLS
OCCUR, CLEAN IMMEDIATELY, TO AVOID THE DANGER OF SLIPS OR
FALLS.
NOTICE: While cooking, the Clamshell® must be monitored at all times. Do not leave
the Clamshell® unattended while cooking.
NOTICE: Fan in Clamshell® runs continuously. For the safety of the unit, the fan
must run continuously to provide cooling to the electrical components.
Component cooling is required if the base unit is running. If power to the
Clamshell® is turned off, gas to base will be turned off. If it is necessary to
remove power from the Clamshell®, the base unit must be cooled below
200°F first.

5
IMPORTANT READ FIRST IMPORTANT
WARNING: KEEP WATER AND SOLUTIONS OUT OF CONTROLS. NEVER SPRAY OR
HOSE CONTROL CONSOLE, ELECTRICAL CONNECTIONS, ETC.
CAUTION: MOST CLEANERS ARE HARMFUL TO THE SKIN, EYES, MUCOUS
MEMBRANES AND CLOTHING. PRECAUTIONS SHOULD BE TAKEN TO
WEAR RUBBER GLOVES, GOGGLES OR FACE SHIELD AND PROTECTIVE
CLOTHING. CAREFULLY READ THE WARNING AND FOLLOW THE
DIRECTIONS ON THE LABEL OF THE CLEANER TO BE USED.
CAUTION: A COMMERCIAL LIQUID GRIDDLE CLEANER IS NOT RECOMMENDED FOR
CLEANING THE GRIDDLE OR CHARBROILER UNDER THE CLAMSHELL®
AS MOST CONTAIN POTASSIUM HYDROXIDE OR SODIUM HYDROXIDE
WHICH IS HARMFUL TO THE CLAMSHELL® BURNER TILES.
NOTICE: Do not spray any liquids on to the tiles, or wipe the tiles with any materials.
Liquids and direct contact on the tiles can damage them.
CAUTION: DO NOT USE YOUR HAND TO CHECK GRIDDLE/CHARBROILER
TEMPERATURE.
NOTICE: Service on this, or any other, LANG appliance must be performed by
qualified personnel only. Consult your authorized service station directory
or call the factory at 1-800-224-LANG (5264), or WWW.LANGWORLD.COM
For the service station nearest you.
DANGER: BOTH HIGH AND LOW VOLTAGES ARE PRESENT INSIDE THIS
APPLIANCE WHEN THE UNIT IS PLUGGED/WIRED INTO A LIVE
RECEPTACLE. BEFORE PERFORMING ANY WORK ON INTERNAL
COMPONENTS, DISCONNECT THE APPLIANCE FROM THE ELECTRIC
POWER SUPPLY.
CAUTION: USE OF ANY REPLACEMENT PARTS OTHER THAN THOSE SUPPLIED BY
LANG OR THEIR AUTHORIZED DISTRIBUTORS CAN CAUSE BODILY
INJURY TO THE OPERATOR AND DAMAGE TO THE EQUIPMENT AND
WILL VOID ALL WARRANTIES.
CAUTION: BE SURE ALL OPERATORS READ, UNDERSTAND AND FOLLOW THE
OPERATING INSTRUCTIONS, CAUTIONS AND SAFETY INSTRUCTIONS
CONTAINED IN THIS MANUAL.

6
2. EQUIPMENT DESCRIPTION
Lang Model: AGC
ADD-ON CLAMSHELL® HOOD
2.1 Exterior Construction
•The Clamshell® dimensions are 19 1/2” (49.53cm) High in the lowered position, 38 1/3” (97.36cm)
High in the raised position, 36 3/4” (93.35cm) Deep, and width is 24” (60.96cm).
•The stainless steel hood makes for easy cleaning.
•Pivoting heat deflector redirects excess grill heat to either side of the equipment and away from
employees.
2.2 Operation
•By heating only when in the down position, you can conserve energy and save money with a cooler
backroom environment.
•Cook different products at the same time with no height adjustments needed.
2.3 Technical
•Griddle operates on either Natural Gas or Propane. This must be specified when ordering. It is
shipped with a Power Cord and Plug attached.
•Clearances required from non-combustible surfaces: Back: 0 inches, Sides: maintain side clearance
of base appliance or 3 inches which ever is greater, Bottom: 6 inches below the bottom of the
stanchions.
2.4 Griddle Gas and Voltage Specifications
The Lang Clamshell® can be connected to any 220 Volt source. The gas specifications are listed on
the data label located on the inside surface of the hood wrap.

7
3. UNPACKING
3.1 Receiving the Clamshell®
Upon receipt, check for freight damage, both visible and concealed. Visible damage should be noted
on the freight bill at the time of delivery and signed by the carrier's agent. Concealed loss or damage
means loss or damage which does not become apparent until the merchandise has been unpacked. If
concealed loss or damage is discovered upon unpacking, make a written request for inspection by the
carrier's agent within 15 days of delivery. All packing material should be kept for inspection. Do not
return damaged merchandise to Lang Manufacturing Company. File your claim with the
carrier.
3.2 Location
Prior to un-crating, move the Clamshell® as near to its intended location as practical. The crating will
help protect the unit from physical damage normally associated with moving it through hallways and
doorways.
NOTICE: If the Clamshell® is to be attached to a griddle/ charbroiler in the field –
it is recommended to complete the installation of mounting adapter
before un-crating the Clamshell®.
3.3 Un-crating the Add-on Clamshell® Hood
If Clamshell® is received already attached to a Griddle/Charbroiler skip to section 3.4.
The Clamshell® will arrive completely assembled inside a wood frame covered by a cardboard box
and bolted to a skid. Remove the cardboard cover, unbolt Clamshell® from the support
brackets. Discard the skid and brackets.
Remove Clamshell® from skid and place in intended location.
There are several parts that are not installed in the unit. Be careful not to misplace the following parts
when un-crating the unit.
Inner Component Cover
Outer Component Cover
Inner Flue
Outer Flue
Insulation
Manual Shut-off Valve
Two 3/8 X 16 Nuts
Note: See Mounting Adapter kit for instructions on installing these parts.
CAUTION: UNIT IS EXTREMELY HEAVY. FOR SAFE HANDLING, INSTALLER
SHOULD OBTAIN HELP AS NEEDED, OR EMPLOY APPROPRIATE
MATERIALS HANDLING EQUIPMENT (SUCH AS A FORKLIFT, DOLLY,
OR PALLET JACK) TO REMOVE THE UNIT FROM THE SKID AND MOVE
IT TO THE PLACE OF INSTALLATION.
3.4 Un-crating Griddle/Charbroiler with Clamshell® Attached
CAUTION: SHIPPING STRAPS ARE UNDER TENSION AND CAN SNAP BACK
WHEN CUT.
The griddle will arrive completely assembled inside a wood frame covered by a cardboard box and
strapped to a skid. Remove the cardboard cover, cut the straps and remove the wood
frame.
Remove griddle from skid and place in intended location. The legs and gas regulator are located in the
grease drawer.

8
4. INSTALLATION
WARNING: INSTALLATION OF THE UNIT MUST BE DONE BY PERSONNEL
QUALIFIED TO WORK WITH ELECTRICITY AND PLUMBING.
IMPROPER INSTALLATION CAN CAUSE INJURY TO PERSONNEL
AND/OR DAMAGE TO EQUIPMENT. UNIT MUST BE INSTALLED IN
ACCORDANCE WITH ALL APPLICABLE CODES.
NOTICE: The data plate is located on the inside of the hood wrap. The
Clamshell® voltage, wattage, serial number, clearance and gas
specifications are on the data plate. This information should be
carefully read and understood before proceeding with the installation.
NOTICE: This unit is approved to be installed only on equipment which meets
NSF standards, and for which the adapter kit is provided.
4.1 Electrical Connection
The Clamshell® is supplied with a cord. The receptacle is not provided with the Clamshell®.
Follow the receptacle manufacturer’s instructions when connecting the cord to the power supply.
4.2 Gas Connection
WARNING: BEFORE LIGHTING, USE A SOAP AND WATER SOLUTION TO TEST
ALL JOINTS FOR GAS LEAKS.
This Clamshell® is manufactured for use with the type of gas indicated on the nameplate. Contact the
factory if your type of gas does not match the nameplate data.
All gas connectors must be in accordance with local codes and comply with the National Fuel
Federal Gas Codes ANSI Z223.1 latest edition.
There are two gas connections involved in the installation of the Clamshell®:
The first is the gas supply to the Clamshell® itself. This connection should be made positioning
the manual shut-off valve supplied with the Clamshell® to isolate the appliance from the kitchens
main gas supply during any future service activity (See figure 1). (A service agent should be able
to shutoff and disconnect the gas supply to the Clamshell® without effecting the main gas supply
to the kitchen.) Use gas lines that have a minimum diameter of at least 1/2 an inch.
The second is the gas supply to the base appliance (the appliance to which the Clamshell® is
mounted). The Clamshell® has an external solenoid valve (the Automatic Cutoff Valve (ACV))
at the end of a flexible conduit. The ACV must be installed in line with the gas supply to the base
appliance in a location, which will ensure the ACV is not exposed to temperatures above 175°F
(See figure 1). Remove the cover to the ACV to ensure the correct flow direction through the
valve when making the connections. Replace the cover after the connections are complete. Use
gas lines that have a minimum diameter of at least 1/2 an inch.
NOTE: If this Clamshell® is received already mounted on a Lang griddle no further installation is
required. If this Clamshell® is a separate unit proceed to section 4.3 below.
NOTICE: The installation of any components such as a vent hood, grease
extractors, fire extinguisher systems, must conform to their applicable
National, State and locally recognized installation standards.
4.3 Installation Instructions
Refer to the Installation instructions provided with the adapter kit, on how to connect this Clamshell®
to the griddle/charbroiler.

9
4. INSTALLATION CONT’D
Figure 1
Griddle / Charbroiler
ACV
ACV
Manual Shut-off
Valve
Regulator
Legend:
ACV = Automatic Cut-off Valve
A = 1” Pipe
B = Reduction to 3/4” Pipe
C = Reduction to 1/2” Pipe
D = Increase to 3/4” Pipe
O = Optional second AGC Parts
AGC AGC

10
5. INITIAL START UP
5.1 Initial Lighting Procedure for an Clamshell®
WARNING: DURING INITIAL USE, OR USE AFTER SERVICE, IF THE PILOT DOES
NOT IGNITE ON FIRST TRY THE MAIN GAS VALVE MUST BE TURNED
OFF FOR AT LEAST FIVE MINUTES.
NOTICE: While cooking, the Clamshell® must be monitored at all times. Do not
leave the Clamshell® unattended while cooking.
NOTICE: Fan in Clamshell® runs continuously. For the safety of the unit, the fan
must run continuously to provide cooling to the electrical components.
Component cooling is required if the base unit is running. If power to
the Clamshell® is turned off, gas to base will be turned off. If it is
necessary to remove power from the Clamshell®, the base unit must be
cooled below 200°F first.
•The Clamshell® has two positions, the lowered position for cooking and the raised position for griddle
loading, cleaning, or griddle only use.
•No thermostats are provided for temperature control. The Clamshell® is a radiant cooking device,
which operates only in the lowered position.
•Ignition is automatic and occurs as the Clamshell® is lowered.
•Raising the Clamshell® turns the gas burner off.
5.2 Initial Lighting Procedure for the Griddle/Charbroiler
See Operator manual for the griddle/charbroiler.

11
6. OPERATION
6.1 Clamshell® Operation
CAUTION: ALWAYS KEEP THE AREA NEAR THE APPLIANCE FREE FROM
COMBUSTIBLE MATERIALS.
CAUTION: KEEP FLOOR IN FRONT OF EQUIPMENT CLEAN AND DRY. IF SPILLS
OCCUR, CLEAN IMMEDIATELY, TO AVOID THE DANGER OF SLIPS OR
FALLS.
NOTICE: While cooking, the Clamshell® must be monitored at all times. Do not
leave the Clamshell® unattended while cooking.
•The Clamshell® has two positions, the lowered position for cooking and the raised position for
griddle loading, cleaning, or griddle only use.
•No thermostats are provided for temperature control. The Clamshell® is a radiant cooking device,
which operates only in the lowered position.
•Ignition is automatic and occurs as the Clamshell® is lowered.
•Raising the Clamshell® turns the gas burner off.
•Place food on griddle/charbroiler and immediately lower the Clamshell®. The tiles will glow
reddish-orange in approximately 30-45 seconds. The radiant heat from the Clamshell® will cook
from the top while the griddle/charbroiler cooks the product from the bottom.
•Load product under the Clamshell® following the normal loading procedures for the
griddle/charbroiler to which it is attached.
6.2 Operation When Attached to a Griddle/Charbroiler
See Operator’s Manual for the base unit.

12
7. SEQUENCE OF OPERATION
7.1 Power On
•When the Clamshell® is plugged in, 220 Volts is applied to the blower motor. The Clamshell® is
designed to have a constantly running blower motor.
•The air switch then senses the blower motor, closes, and applies the 220 Volts to a 24 VAC transformer.
•The transformer then supplies 24 VAC to the tilt switch, and to the automatic cutoff valve.
•The 24 VAC to the automatic cutoff valve opens the gas valve to the griddle/charbroiler, thus allowing the
base unit to operate.
•When the Clamshell® is lowered, the tilt switch allows 24 VAC to go to the spark module.
•The spark module then supplies 24 VAC to open the Clamshell® gas valve, and high voltage to the spark
igniter.
•When the burner ignites, the sense probe senses the flame is ignited and the spark module turns off the high
voltage to the spark igniter.
•When the Clamshell® is raised the tilt switch opens the 24 VAC to the spark module, which removes the
24 VAC to the gas valve, turning off the Clamshell®.

13
8. MAINTENANCE & CLEANING
WARNING: KEEP WATER AND SOLUTIONS OUT OF CONTROLS. NEVER SPRAY OR
HOSE CONTROL CONSOLE, ELECTRICAL CONNECTIONS, ETC.
CAUTION: MOST CLEANERS ARE HARMFUL TO THE SKIN, EYES, MUCOUS
MEMBRANES AND CLOTHING. PRECAUTIONS SHOULD BE TAKEN TO
WEAR RUBBER GLOVES, GOGGLES OR FACE SHIELD AND PROTECTIVE
CLOTHING. CAREFULLY READ THE WARNING AND FOLLOW THE
DIRECTIONS ON THE LABEL OF THE CLEANER TO BE USED.
CAUTION: A COMMERCIAL LIQUID GRIDDLE CLEANER IS NOT RECOMMENDED FOR
CLEANING THE GRIDDLE OR CHARBROILER UNDER THE CLAMSHELL®
AS MOST CONTAIN POTASSIUM HYDROXIDE OR SODIUM HYDROXIDE
WHICH IS HARMFUL TO THE CLAMSHELL® BURNER TILES.
NOTICE: Do not spray any liquids on to the tiles, or wipe the tiles with any materials.
Liquids and direct contact on the tiles can damage them.
8.1 Weekly Cleaning
•The Clamshell® tiles are self cleaning, which is accomplished by leaving the Clamshell® on with no
product being cooked, thus allowing the heat of the broiler to burn debris from the tiles.
•To clean the Clamshell®, start with a clean griddle plate.
•Turn off the griddle/charbroiler thermostats and wait until the griddle/charbroiler is cool.
CAUTION: DO NOT USE YOUR HAND TO CHECK GRIDDLE/CHARBROILER
TEMPERATURE.
•Lower the Clamshell® and let it run for 45 minutes, then raise the Clamshell® and ensure the blower motor
continues to blow cooling air through the burner tiles (Do not unplug or turn off Clamshell® power).
•Once the Clamshell® has cooled, wipe ash from around the burner tiles. Take care not to touch the burner
tiles with the cleaning rag.
NOTICE: Do not spray any liquids on to the tiles, or wipe the tiles with any materials.
Liquids and direct contact on the tiles can damage them.
8.2 Burner Air Shutter Adjustment
•The air shutters are pre-set at the factory, and should not need adjustment. However, if adjustments are be
required, contact your local authorized service station for instructions.
8.3 Disconnecting Power from Blower Motor
If power is to be removed from the blower motor, the following must be completed:
The gas to the base unit and the gas to the Clamshell® must be turned off.
The base unit must be cooled below 200°F.

14
9. TROUBLESHOOTING
9.1 Symptoms
What follows is a chart of Symptoms and Possible Causes to aid in diagnosing faults with the Clamshell®.
Refer to the Symptoms column to locate the type of failure then to the Possible Cause for the items to be
checked.
To test for a possible cause, refer to the TEST section and locate the Possible Cause then refer to test to
identify test procedures.
SYMPTON POSSIBLE CAUSE
Igniter not sparking •Failed spark module
•Failed tilt switch
•Failed air switch
•Failed motor blower
•Failed transformer
•Failed spark electrode
Spark but no ignition •Failed spark controller
•Failed gas solenoid valve
•Clamshell® gas valve turned off
•Plugged orifice
Clamshell® turns off after extended use •Incorrectly adjusted sense electrode
Taking too long to light •Incorrectly adjusted spark electrode
•Plugged enrichment orifice
•Plugged burner tiles
Hazy blue flame on tile face •Incorrectly adjusted air shutter
•Leak in air path to burner face
•Incorrectly adjusted gas regulator
Not hot enough •Incorrectly adjusted gas regulator
•Plugged main burner orifice
•Plugged burner tiles
Clamshell® not turning off •Failed tilt switch
•Failed gas solenoid valve
Blower runs continuously •Normal operation

15
9. TROUBLESHOOTING CONT’D
9.2 TESTS
NOTICE: Service on this, or any other, LANG appliance must be performed by
qualified personnel only. Consult your authorized service station directory
or call the factory at 1-800-224-LANG (5264), or WWW.LANGWORLD.COM
For the service station nearest you.
WARNING: BOTH HIGH AND LOW VOLTAGES ARE PRESENT INSIDE THIS
APPLIANCE WHEN THE UNIT IS PLUGGED/WIRED INTO A LIVE
RECEPTACLE. BEFORE REPLACING ANY PARTS, DISCONNECT THE
UNIT FROM THE ELECTRIC POWER SUPPLY AND CLOSE THE MAIN GAS
VALVE. ALLOW FIVE MINUTES FOR UNBURNED GAS TO VENT.
If an item on the list is followed by an asterisk (*), the work should be done by a factory
authorized service representative.
Possible Cause TEST
Failed tilt switch •Unplug switch and test for continuity while raising/lowering
the hood
Failed gas valve •Remove the wires and check for continuity across the valve
coil
Failed spark module •Check for 24 VAC on TH*
•Observe spark
Failed air switch •Unplug switch and test for continuity while blower motor is
running*
Failed combustion blower •Check for proper voltage to unit/blower*
•Check for continuity across the motor’s windings
Improper gas pressure •Ensure gas pressure is adjusted properly*
Failed transformer •Check for proper voltage*
CAUTION: USE OF ANY REPLACEMENT PARTS OTHER THAN THOSE SUPPLIED BY
LANG OR THEIR AUTHORIZED DISTRIBUTORS CAN CAUSE BODILY
INJURY TO THE OPERATOR AND DAMAGE TO THE EQUIPMENT AND
WILL VOID ALL WARRANTIES.

16
10. PARTS LIST
Item No. Part# Descri
p
tion
1103-73 HANDLE
2103-19 HOOD WRAP
3103-193 HOOD SKIRT, LEFT SIDE
3103-194 HOOD SKIRT, RIGHT SIDE
3103-197 HOOD SKIRT, FRONT W/ HINGE
450201-08 WIRE GUARD ADD ON BROILER
580302-06 IGNITION / SENSOR, FR 310.5 ref151.26 255.3 0.f236.48.2(, FR 310.06>>BDCBT9 0 057.4 Tm05257.4 Tm-0.0023 Tc[(803)-6.1(025c0 Tw(3)TjETEMC/P <</MR 310.06>>BDBT9 0 03 9 256.BURNER m00.7201 - Tm(LE ASSEMBLY.6(T)-9.1(I)4.6(O)-44DD ON BROILER)TjETEMC7044DD ON BROILER)TjEref15144DD ON BROILER)TjEref23644DD ON BROILER

17
10. PARTS LIST CONT’D
Item No. Part# Descri
p
tion
16 103-61 TUBE #2
17 80501-10 REGULATOR GAS SET 3 1/2" NG BROILER
18 80300-10 MODULE SPARK IGNITOR BROILER
*30307-02 CLIP MOUNT MERCURY TILTSWITCH
19 30307-01 SWITCH MERCURY TILTSWITCH
20 103-14 TUBE #1
21 70101-28 UNION ELBO 90 DEGREESTL 3/8"
22 51002-11 HOOD SPRING AGC
23 51002-05 SPRING COMPRESSION INNER-BROILER
24 80403-04 90 DEGREE FITTING W/#29 DRL NG
*80403-05 90 DEGREE FITTING W/#44 DRL LP
25 103-64 TUBE #3
26 70101-50 BRAS TBE TEE 3/8-3/8-1/4
27 103-70 TUBE #4
28 80502-03 VALVE SOLENOID GAS 24V
29 AGBS-A17 PILOT ASSEMBLY AGC
30 GCH-516-1 SENSE WIRE
31 GCH-515-1 SPARK WIRE
*70101-62 HOSE FLEX GAS 27" 1/2" NPT -3/8"T
*GCH-232-1 SEAL FIBER
*GCH-232-2 WASHER AGC
*74001-01 HOSE 1/4" DIA NEOPRENE LOW PRESS
*70101-61 FITTING 1/4" HB TO 1/2" NPT-M WT
*70505-07 CONDUIT CNNCTR 3/8" 90 DEGREE FLEX
*70505-06 CONDUIT CNNCTR 3/8" FLEX
*=NOT SHOWN
16 17 18 19
20
21
22&23
24
25
26
27
28
29 30 31

18
11. WIRING DIAGRAM

19
12. WARRANTY
Lang Manufacturing Limited Warranty
to Commercial Purchasers*
(Domestic U.S., Hawaii, &
Canadian Sales only.)
Lang Manufacturing Equipment (“Lang Equipment”)
has been skillfully manufactured, carefully inspected
and packaged to meet rigid standards of excellence.
Lang warrants its Equipment to be free from defects in
material and workmanship for (12) twelve consecutive
months, with the following conditions and subject to
the following limitations.
I. This parts and labor warranty is limited to Lang
Equipment sold to the original commercial
purchaser/users (but not original equipment
manufacturers), at its original place of installation, in
the continental United States, Hawaii and Canada.
Quartz elements are warranted for ninety(90) days from
the date of installation.
II. Damage during shipment is to be reported to the
carrier, is not covered under this warranty, and is the
sole responsibility of purchaser/user.
III. Lang, or an authorized service representative, will
repair or replace, at Lang’s sole election, and Lang
Equipment, including but not limited to, safety valves,
gas and electric components, found to be defective
during the warranty period. As to warranty service in
the territory described above, Lang will absorb labor
and portal to portal transportation costs (time &
mileage) for the first (12) twelve months from the date
of installation or eighteen (18) months from date of
shipment from Lang Manufacturing, which ever comes
first.
IV. This warranty does not cover routine general
maintenance, periodic adjustments, as specified in
operating instructions or manuals, and consumable
parts such as quartz elements, or labor costs incurred
for removal of adjacent equipment or objects to gain
access to Lang Equipment. This warranty does not
cover defects caused by improper installation,
abuse, careless operation, or improper maintenance
of equipment.
V. THIS WARRANTY IS EXCLUSIVE AND IS
IN LIEU OF ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING ANY
IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, EACH OF WHICH IS
HEREBY EXPRESSLY DISCLAIMED. THE
REMEDIES DESCRIBED ABOVE ARE
EXCLUSIVE AND IN NO EVENT SHALL LANG
BE LIABLE FOR SPECIAL, CONSEQUENTIAL
OR INCIDENTAL DAMAGES FOR THE
BREACH OR DELAY IN PERFORMANCE OF
THIS WARRANTY.
VI. Lang Equipment is for commercial use only. If
sold as a component of another(OEM)
manufacturer’s equipment, or if used as a consumer
product, such Equipment is sold AS IS and without
any warranty.