Lang onyxTOUCH User manual
Quick start guide version 1.0
Quick start guide onyxTOUCH version 1.0
LANG AG
01.01.2016
Page 2 of 6
onyxTOUCH quick start guide version 1.0
1. What comes with your onyxTOUCH?......................................................................................... 3
2. Installation ............................................................................................................................... 3
2.1 Mechanical Installation ................................................................................................................. 3
2.2 Software Installation ..................................................................................................................... 3
3. Calibration ............................................................................................................................... 4
5. Technical data onyxTOUCH ....................................................................................................... 5
Quick start guide onyxTOUCH version 1.0
LANG AG
01.01.2016
Page 3 of 6
1. What comes with your onyxTOUCH?
The onyxTOUCH is a multi touch display which works with InGlass touch technology based
on total internal reflection of light. Following accessories are included:
Power supply cable for the display
Remote control for the display
Mains adaptor incl. cable
USB cable (USB Type A Male / A Male)
USB extension cable (USB Type A)
USB stick including all necessary documentation and software
2. Installation
2.1 Mechanical Installation
As onyxTOUCH display components are always LCD, some installations are not allowed.
This could be an installation in a table or maybe in portrait mode. Please make sure the
display manufacturer allows the way you want to install the display. In some cases it might
be necessary to install additional fans to guarantee a safe ventilation of the display.
2.2 Connection to PC
To use the system with a PC please connect the USB cable (Type A Male / A Male) with an
USB 2.0 port of the PC. Note that you have to use USB 2.0 because compatibility is not
complete at USB 3.0. If necessary you can also use the USB extension. Plug in the mains
adaptor at the onyxTOUCH and fix the nut carefully. Make sure that each cable is clipped to
the cable anchorage to prevent broken controller parts.
2.3 Installation on Linux/Android
onyxTOUCH supports ARM/Linux and ARM/Linux/Android, for both X86 and ARM. If the
Linux Kernel version is 3.5 or higher, the HID multitouch driver is included in mainline Kernel
and will work out-of-the-box. If 3.4 or older, you may need to apply a patch to add multitouch
support ("hid-multitouch driver with autodetection").
Quick start guide onyxTOUCH version 1.0
LANG AG
01.01.2016
Page 4 of 6
2.4 Installation on Windows
onyxTOUCH supports Windows since Windows 7.
If you are using a Windows system there is no driver installation necessary, the onyxTOUCH
will be recognised as a HID device. Just connect the mains adapter and USB cable like
described above and the device will be shown in the device manager after a few seconds.
If it is not shown and the touch function doesn’t work, please make sure that everything is
connected correctly. Furthermore you can contact the support directly:
info@solutions4interactivity.com
3. Calibration
Generally there is no calibration necessary. If you need to calibrate the onyxTOUCH you
have to use a Windows system. Please go to the Windows calibration function under Tablet
PC Settings (Figure 1)
Before calibrating - make sure your display is set to its native resolution - otherwise problems
might occur on the display side causing the offset error.
Please Note that Windows 8 has a tool built-in. Search for “calibrate” in Windows and it will
show up.
Figure 1 Tablet PC Settings
Quick start guide onyxTOUCH version 1.0
LANG AG
01.01.2016
Page 5 of 6
5. Technical data onyxTOUCH
Interface
Connection USB 2.0 (Hi Speed)
connector type A
Operating system Windows 7 / 8 / 10, Linux, Android
MAC OS (via 3rd party driver)
Software interface HID, native Windows 7 / 8 / 10 touch commands
TOUCH
Technology InGlass Touch Technology
Frame rate 100 FPS
Response time 15 - 25 ms
Touch points detects up to 20 touch points simultaneously
Touch point accuracy < 2 mm
Method detects any kind of object with soft surface
(Finger, gloved finger, grounded stylus,...)
Stylus Tip Size min. 4 mm
Optional Features 10-bit pressure detection
Mechanical Data
Materials black coated stainless steel, glass
Cover Front Glass Type chemically strengthened soda lime
Cover Front Glass Thickness 3.2 mm single glass
Warranty 24 months, excluded: Protection glass,
USB cable
Quick start guide onyxTOUCH version 1.0
LANG AG
01.01.2016
Page 6 of 6
Imprint:
LANG AG
Schlosserstraße 8
51789 Lindlar
Germany
Telephone +49 (0)2266 4764-0
Fax +49 (0)2266 4764-43
E-Mail [email protected]
www.lang-ag.com
Table of contents
