Lansdale LPBT Series Operating and maintenance manual

1
FEATURES
1. All sizes have been UL/FM certified and rated
to 300 psi.
2. All valves have an integral pre- ired
supervisory tamper s itch assembly. The
tamper s itch signals movement of the valve
disc from the full open position, hen
correctly ired.
3. S itch rating: 10 Amps/115 VAC-60Hz
0.5 Amps/28 VDC
4. All vlaves are furnished ith tamper s itch
assemblies for indoor and outdoor use.
5. A 1/4 turn valve ith slo closing and
opening ill prevent ater hammer and
shock from damaging the fire protection
system.
MODEL LPBT LPBG
TYPE Threaded end Grooved end
RATING 300 PSI
PN20 2065KPa
300 PSI
PN20 2065KPa
SIZE
1”, 1-1/4”,
1-1/2”, 2”,
2-1/2”
1-1/4”, 1-1/2”,
2”, 2-1/2”
INSTALLATION
1. The valve can be installed in any orientation
in a piping system ith standard ASME
B1.20.1 NPT or standard roll or cut grooved
pipe.
2. When threading to pipe, apply adequate
pipe sealants, use a rench to clamp on the
hexagon end of the valve.
3. The tamper has t o s itches: s itch-1 has
dual leads on the terminals. This s itch is
used for connection of the supervisory circuit
of a listed fire alarm control panel.
S itch 2 has a single lead and used for
connection of auxiliary equipment. All the
unused ires need to be capped ith lead
nuts and tucked into a jucntion box. All
connections need to be revie ed and
approved by the AHJ.
4. A No.14 green ire is fixed inside the s itch
housing. It is provided as a ground for the
housing.
5. Installation must comply ith NFPA 13 and
NFPA 72.
6. The valves are intended for use ith ANSI
B36.10 Schedule 40 and/or Schedule 80 pipe,
sizes 1”, 1-1/4”, 1-1/2”, 2” and 2-1/2”
IMO
–
REV1
-
510
Installation Maintenance
& Operating Instructions
POWERBALL 300
LPBT & LPBG SERIES
1” ~ 2 1/2”, THREADED
1 1/4”~2 1/2” GROOVED
www.Breccocorp.com

2
MAIN DIMENSIONS ─
──
─ UNIT:INCHES MATERIAL LIST
LPBT (Threaded Ends) NO.
NAME MATERIAL
SIZE 1” 1-1/4” 1-1/2” 2” 2-1/2” 1 BODY BRONZE ASTM 584 C83600
A 2.13 2.63 2.87 3.25 4.49 2 DISC SS304
H 4.94 5.13 5.59 6.13 6.58 3 HANDWHEEL ASTM A216 WCB
L 1.56 1.94 2.19 2.76 3.41 4 SEAT ASTM D2000 VITON
M 1.75 2.17 2.37 3.11 3.78 5 INDICATOR POWDER METAL FD0205 95HT
LPBG (Grooved Ends)
6 HOUSING BRASS ASTM B16 C36000
SIZE 1” 1-1/4” 1-1/2” 2” 2-1/2” 7 COVER BRASS ASTM B16 C36000
A 3.86 4.02 4.09 4.49
H 5.20 5.47 6.07 6.58
P 0.63 0.63 0.63 0.63
O 0.31 0.31 0.31 0.31
M 1.54 1.78 2.25 2.72
L 1.67 1.90 2.37 2.87
NOTE:
Grooved ends to AWWA C606 for steel pipe.
Packing Gland with Adjustable Glands shall be accessible for
tightening stem seals without the disassembly of the valve or
operator parts U.S. Patented 6629.683.B2

3
WIRING DIAGRAM
SWITCH SHOWN POSITION WITH VALVE IN FULL OPEN
SWITCH 1 : DUAL LEADS SOLDERED TO SWITCH TABS
SWITCH 2 : SINGLE LEADS SOLDERED TO SWITCH TABS
Green wire is provided as ground for the switch housing.
Switch rating: 10 Amps/ 115 VAC-60Hz 0.5 Amps/28 VDC
Installation must comply with NFPA 13 and NFPA 72.
Cap unused leads with wire nuts and tuck into a jucntion box (not provided).
Agent:

4