Lantech IES-22812F-2P User manual

User Manual
V1.01
Nov-2010
Lantech
IES-22812F-2P
12 100FX + 8 10/100TX + 2 1000 SFP Industrial Power
Station L2 Plus Managed Switch

FCC Warning
This Equipment has been tested and found to comply with the limits for a Class-A
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy. It may
cause harmful interference to radio communications if the equipment is not installed
and used in accordance with the instructions. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

Content
Chapter 1 Introduction............................................ 1
1.1 Hardware Features ...................................................1
1.2 Software Features.....................................................2
1.3 Package Contents.....................................................4
Chapter 2 Hardware Description............................ 5
2.1 Physical Dimensions.................................................5
2.2 Front (LED) Panel .....................................................5
2.3 Rear Panel ................................................................6
2.4 LED Indicators...........................................................7
Chapter 3 Hardware Installation ............................ 9
3.1 Rack-mounted Installation.........................................9
3.2 Cabling....................................................................11
3.3 Wiring the Power Inputs..........................................14
3.4 Wiring the P-Fail Alarm Contact..............................15
Chapter 4 Network Application ............................ 16
4.1 X-Ring Application...................................................17
4.2 Coupling Ring Application.......................................18
4.3 Dual Homing Application.........................................19
Chapter 5 Console Management .......................... 20
5.1 Connecting to the Console Port ..............................20
5.2 Pin Assignment .......................................................20
5.3 Login in the Console Interface ................................21
5.4 CLI Management.....................................................22

5.5 Commands Level ....................................................22
Chapter 6 Web-Based Management ..................... 24
6.1 About Web-based Management .............................24
6.2 Preparing for Web Management.............................24
6.3 System Login...........................................................25
6.4 System Information .................................................26
6.5 IP Configuration ......................................................27
6.6 DHCP Server ..........................................................28
6.6.1 System configuration ..............................................29
6.6.2 Client Entries...........................................................30
6.6.3 Port and IP Bindings ...............................................31
6.7 TFTP .......................................................................32
6.7.1 Update Firmware ....................................................32
6.7.2 Restore Configuration.............................................33
6.7.3 Backup Configuration..............................................34
6.8 System Event Log...................................................35
6.8.1 Syslog Configuration...............................................35
6.8.2 System Event Log—SMTP Configuration...............37
6.8.3 System Event Log—Event Configuration................39
6.9 Fault Relay Alarm....................................................41
6.10 SNTP Configuration ................................................42
6.11 IP Security...............................................................46
6.12 User Authentication.................................................48
6.13 Advanced Configuration..........................................49
6.13.1 Broadcast Storm Filter............................................49
6.13.2 Aging Time.............................................................51

6.13.3 Jumbo Frame.........................................................52
6.14 Port Statistics ..........................................................53
6.15 Port Counters..........................................................55
6.16 Port Control.............................................................58
6.17 Port Trunk................................................................60
6.17.1. Aggregator setting.................................................60
6.17.2. Aggregator Information..........................................62
6.17.3. State Activity..........................................................66
6.18 Port Mirroring...........................................................68
6.19 Rate Limiting ...........................................................69
6.20 VLAN configuration .................................................70
6.20.1. Port-based VLAN ..................................................70
6.20.2. 802.1Q VLAN........................................................74
6.21 Rapid Spanning Tree ..............................................79
6.21.1. System Configuration............................................79
6.21.2. Port Configuration .................................................81
6.22 SNMP Configuration ...............................................83
6.22.1. System Configuration............................................83
6.22.2. Trap Configuration.................................................85
6.22.3. SNMPV3 Configuration.........................................86
6.23 QoS Configuration...................................................89
6.24 IGMP Configuration.................................................91
6.25 Pro-Ring ..................................................................93
6.26 LLDP Configuration.................................................95
6.27 Security—802.1X/Radius Configuration..................96
6.27.1. System Configuration............................................96
6.27.2. Port Configuration .................................................97

6.27.3. Misc Configuration.................................................98
6.28 MAC Address Table..............................................100
6.28.1. Static MAC Address............................................100
6.28.2. MAC Filtering.......................................................102
6.28.3. All MAC Addresses .............................................103
6.28.4. MAC Address Table—Multicast Filtering.............104
6.29 Access Control List ...............................................106
6.30 Factory Default......................................................107
6.31 Save Configuration................................................108
6.32 System Reboot......................................................109
Troubleshooting ................................................... 110
Appendix A — RJ-45 Pin Assignment................... 111
Appendix B — Command Sets.............................. 114
Commands Set List...........................................................114
System Commands Set.....................................................114
Port Commands Set..........................................................118
Trunk Commands Set .......................................................120
VLAN Commands Set.......................................................122
Spanning Tree Commands Set.........................................124
QOS Commands Set.........................................................127
IGMP Commands Set .......................................................128
Mac / Filter Table Commands Set.....................................129
SNMP Commands Set......................................................131
Port Mirroring Commands Set...........................................134
802.1x Commands Set......................................................135
TFTP Commands Set........................................................138
SystemLog, SMTP and Event Commands Set .................139

SNTP Commands Set.......................................................142
Pro-Ring Commands Set...................................................144
LLDP Command Set .........................................................145
Access Control List Command Set....................................146

1
Chapter 1 Introduction
1.1 Hardware Features
Switch Architecture Back-plane (Switching Fabric): 8Gbps
Packet throughput ability(Full-Duplex): 11.9Mpps @64bytes
Transfer Rate 14,880pps for Ethernet port
148,800pps for Fast Ethernet port
1,488,000pps for Gigabit Fiber Ethernet port
Packet Buffer 4Mbits
Mac Address 8K MAC address table
Flash ROM 4Mbytes
DRAM 64Mbytes
Jumbo Frame 9022bytes (for Gigabit ports)
Connector 10/100TX: 8 x RJ-45
100FX : 12 x SC
Gigabit Mini-GBIC: 2 x Mini-GBIC sockets
Console port: RJ-45 type
Network Cable 10Base-T: 2-pair UTP/STP Cat. 3, 4, 5 cable
EIA/TIA-568 100-ohm (100m)
100Base-TX: 2-pair UTP/STP Cat. 5/5E cable
EIA/TIA-568 100-ohm (100m)
Optical Cable Multi-mode: 50/125um~62.5/125um
Single-mode: 9/125um
Protocol CSMA/CD
The 8 10/100TX + 12 100FX + 2 Gigabit Mini-GBIC Managed Industrial Switch is
a cost-effective solution and meets the high reliability requirements demanded
by industrial applications. The 8 10/100TX + 12 100FX + 2 Gigabit Mini-GBIC
Managed Industrial Switch can be easily managed through the Web GUI. Using
fiber port can extend the connection distance that increases the network
elasticity and performance. It provides the X-Ring function that can prevent the
network connection failure, and meets the standard of IEC-61850-3 and IEEE-
1613 for the substation environment applications.

LED Front Panel
Per unit: Power 1 (Green), Power 2 (Green), P-Fail (Red),
R.Master (Green)
Port1~22 : Link/Activity (Green), Port13~20: 100M (Green)
Rear Panel
Per unit: Power 1 (Green), Power 2 (Green), P-Fail (Red),
R.Master (Green)
Port1~22 : Link/Activity (Green), Port13~20: Full-duplex
(Amber)
Reverse Polarity
Protection Present
Overload Current
Protection Present
Power Supply AC/DC
Power
Consumption 27.6 Watts max. @ 110 VDC
26.2 Watts max. @ 110 VAC
Operating Humidity 5% to 95% (Non-condensing)
Operating
Temperature Wide Operating Temperature (-40℃~85℃)
Storage
Temperature -40 to 85℃℃
Case Dimensions Metal case. IP-30, 440mm (W) x 44mm (H) x 280mm (D)
Installation DIN-rail and Wall-mount Design
1.2 Software Features
Management SNMP v1 v2c, v3 / Web / Telnet / CLI
SNMP MIB RFC 1215 Trap, RFC1213 MIBII, RFC 1157 SNMP MIB,
RFC 1493 Bridge MIB, RFC 2674 VLAN MIB, RFC 1643 ,
RFC 1757, RSTP MIB, LLDP MIB, Private MIB
VLAN Port Based VLAN
IEEE 802.1Q Tag VLAN (256 entries)/ VLAN ID (Up to 4K,
VLAN ID can be assigned from 1 to 4094.)
GVRP (256 Groups)
Port Trunk with
LACP LACP Port Trunk: 13 Trunk groups/Maximum 4 trunk
members
LLDP Support LLDP to allow switch to advise its identification and
capability on the LAN
2
IES-22812F-2P: 100~240V
IES-22812F-2P:

Spanning Tree Support IEEE802.1w Rapid Spanning Tree
Pro-Ring Support X-Ring, Dual Homing, Couple Ring Topology.
Provide redundant backup feature and the recovery time
below 10ms.
Quality of Service The quality of service determined by port, Tag and IPv4
Type of service, IPv4 Different Service
Class of Service Support IEEE802.1p class of service, per port provides 4
priority queues
Port Security Support 50 entries of MAC address for static MAC and
another 50 for MAC filter
Port Mirror Support 3 mirroring types: “RX, TX and Both packet”.
IGMP Support IGMP snooping v1,v2
256 multicast groups and IGMP query
IP Security Support 10 IP addresses that have permission to access the
switch management and to prevent unauthorized intruder.
Login Security Support IEEE802.1x Authentication/RADIUS
Bandwidth Control Support ingress packet filter and egress packet limit
The egress rate control supports all of packet type and the
limit rates are 0~100Mbps for Port1~20 and 0~1000Mbps for
Port21/22.
Flow Control Support Flow Control for Full-duplex and Back Pressure for
Half-duplex
System Log Support System log record and remote system log server
SMTP Support SMTP Server and 6 e-mail accounts for receiving
event alert
Relay Alarm Provides one relay output for port breakdown & power failure
Alarm Relay current carrying ability: 1A @ DC24V
SNMP Trap Up to 3 Trap stations
Cold start, Warm start, Port link up, Port link down,
Authentication Failure, Port fault relay alarm, X-Ring
topology change
DHCP Provide DHCP Client/ DHCP Server functions
DNS Provide DNS client feature and support Primary and
Secondary DNS server
SNTP Support SNTP to synchronize system clock in Internet
Firmware Update Support TFTP firmware update, TFTP backup and restore.
Configuration
Upload and Support binary configuration file for system quick installation
3

Download
ifAlias Each port allows an alphabetic string of 128-byte assigned
as its own unique name via the CLI or SNMP interface.
1.3 Package Contents
Please refer to the package content list below to verify them against the checklist.

User manual x 1
Mounting plate x 2
RJ-45 to DB9-Female cable x 1
Compare the contents of the industrial switch with the standard checklist above. If any
item is damaged or missing, please contact the local dealer for service.
4
12 100FX + 8 10/100TX + 2 1000 SFP Industrial Power Station L2+ Managed Switch x 1

5
Chapter 2 Hardware Description
In this paragraph, we will describe the Industrial switch’s hardware spec, port, cabling
information, and wiring installation.
2.1 Physical Dimensions
Mechanical Dimensions
2.2 Front (LED) Panel
Front Panel of the industrial switch
12 100FX + 8 10/100TX + 2 1000 SFP Industrial Power Station L2+ Managed Switch
dimensions (W x H x D) are 440mm x 44mm x 280mm as the figure shown below.
The figure below illustrates the front panel of the 12 100FX + 8 10/100TX + 2 1000 SFP
Industrial Power Station L2+ Managed Switch.

2.3 Rear Panel
The 12 fiber ports, 8 copper ports, 2 SFP ports, console port and terminal block are
located on the rear panel of the Managed Industrial Switch.
Front Panel of the industrial switch
6

2.4 LED Indicators
The diagnostic LED indicators located on the front panel & rear panel of the industrial
switch provide real-time information of the system and optional status. The following
table provides description of the LED status and their meanings for the switch.
Front Panel
LED Color Status Meaning
On The switch is the MASTER device of the X-Ring group
R.M. Green Off The switch is not the MASTER device of the X-Ring group
On
zPower1 is inactive
zPower2 is inactive
zPort Link-down
zPort Link-broken
P-Fail Red
Off No failure occurs
On Power 1 is active
P1 Green Off Power 1 is inactive
On Power 2 is active
P2 Green Off Power 2 is inactive
On 1000M (21, 22)
100M (1 ~ 20)
SPD Green
Off 10M (13 ~ 20)
On The port is connected to network
Blinking Packet transmitting/receiving
LNK/ACT Green
Off Not connected to network
7

Rear Panel
LED Color Status Meaning
On The switch is the MASTER device of the X-Ring group
R.M. Green Off The switch is not the MASTER device of the X-Ring group
On
zPower1 is inactive
zPower2 is inactive
zPort Link-down
zPort Link-broken
P-Fail Red
Off No failure occurs
On Power 1 is active
P1 Green Off Power 1 is inactive
On Power 2 is active
P2 Green Off Power 2 is inactive
On The port is connected to network
Blinking Packet transmitting/receiving
LNK/ACT
(Port 1~22) Green
Off Not connected to network
On Full-duplex
FDX
(Port 13~20) Amber Off Half-duplex
8

9
Chapter 3 Hardware Installation
3.1 Rack-mounted Installation
A. Position one bracket to align with the holes on one side of the switch and secure
it with the smaller bracket screws. Then attach the remaining bracket to the other
side of the Switch.
Figure 2-4. Attach mounting brackets with screws
B.
The 12 100FX + 8 10/100TX + 2 1000 SFP Industrial Power Station L2+ Managed Switch
comes with a rack-mounted kit and can be mounted in an EIA standard size, 19-inch Rack.
The Switch can be placed in a wiring closet with other equipment.
Perform the following steps to rack mount the switch:
After attaching the mounting brackets, position the 12 100FX + 8 10/100TX + 2
1000 SFP Industrial Power Station L2+ Managed Switch in the rack by lining
up the holes in the brackets with the appropriate holes on the rack. Secure
the Switch to the rack by a screwdriver with the rack-mounting screws.

Figure 2-5. Mount the Switch in 19” Rack
Note: For proper ventilation, allows about at least 4 inches (10 cm) of clearance on
the front and 3.4 inches (8 cm) on the back of the Switch. This is especially important
for enclosed rack installation.
10

11
3.2 Cabling
Twisted-pair segment can be established by using unshielded twisted pair (UTP) or
shielded twisted pair (STP) cabling. The cable between the link partner (switch, hub,
workstation, etc.) and the switch must be less than 100 meters (328 ft.) long and
comply with the IEEE 802.3ab 1000Base-T standard for Category 5e or above.
The small form-factor pluggable (SFP) is a compact optical transceiver used in optical
communications for both telecommunication and data communication applications.
Please note that you must use the class I optical transceivers which conform to U.S.
code of federal regulation, 21 CFR 1040.
To connect the transceiver and LC cable, please follow the steps shown as below:
First, insert the transceiver into the mini-GBIC slot. Notice that the triangle mark
indicates bottom of the slot.
Transceiver to the SFP slot
Make sure the transceiver is aligned correctly and then slide it into the mini-GBIC slot
until a click is heard.

Transceiver Inserted
Second, insert the fiber cable of LC connector into the transceiver.
LC connector to the transceiver
12

13
To remove the LC connector from the transceiver, please follow the steps shown
below:
First, press the upper side of the LC connector from the transceiver and pull it out to
release.
Remove LC connector
Second, push down the metal loop and pull the transceiver out by the plastic part.
Transceiver pulled out from the SFP slot