Lantech IPES-0204DFT-4 User manual

Lantech
IPES-0204DFT-4
4 10/100TX PoE at/af + 1 10/100/1000T + 1 Dual Speed SFP Industrial Unmanaged Switch
IPES-0104GT-4
4 10/100TX PoE at/af + 1 10/100/1000T Industrial Unmanaged Switch
IES-0204DFT
4 10/100TX + 1 10/100/1000T + 1 Dual Speed SFP Industrial Unmanaged Switch
User Manual
V1.00
May-2016

Recommendation for Shielded network cables
STP cables have additional shielding material that is used to reduce external interference. The
shield also reduces the emission at any point in the path of the cable. Our recommendation is
to deploy an STP network cable in demanding electrical environments. Examples of
demanding indoor environments are where the network cable is located in parallel with
electrical mains supply cables or where large inductive loads such as motors or contactors are
in close vicinity to the camera or its cable. It is also mandatory to use an STP cable where the
power device (like IP camera) is used outdoors or where the network cable is routed outdoors.

Content
Overview.............................................................1
Introduction ..............................................................1
Features / Model List................................................2
Packing List..............................................................3
Safety Precaution.....................................................3
Hardware Description.........................................4
Dimensions ..............................................................4
Wiring the Power Inputs...........................................7
Wiring the Fault Alarm Contact................................8
LED Indicators..........................................................9
Dip Switch (IES-0204DFT / IPES-0204DFT-4)......10
RJ-45 Pin Assignments..........................................11
Cabling...................................................................13
Mounting Installation ........................................17
DIN-Rail Mounting..................................................17
Wall-Mount Plate Mounting (Optional)...................19
Hardware Installation........................................20

Installation Steps....................................................21
Troubleshooting................................................22
Recommendation for Shielded network
cables
STP cables have additional shielding material that is used to reduce external interference.
The shield also reduces the emission at any point in the path of the cable. Our
recommendation is to deploy an STP network cable in demanding electrical
environments. Examples of demanding indoor environments are where the network
cable is located in parallel with electrical mains supply cables or where large inductive
loads such as motors or contactors are in close vicinity to the camera or its cable. It is
also mandatory to use an STP cable where the power device (like IP camera) is used
outdoors or where the network cable is routed outdoors.

Important Notice
Lantech Communications Global, Inc. reserves the right to modify the
equipment, its specification or this manual without prior notice, in the
interest of improving performance, reliability, or servicing. At the time of
publication all data is correct for the operation of the equipment at the
voltage and/or temperature referred to. Performance data indicates typical
values related to the particular product.
No part of this documentation or information supplied may be divulged to
any third party without the express written consent of Lantech
Communications Global Inc. Products offered may contain software which is
proprietary to Lantech Communications Global Inc. The offer or supply of
these products and services does not include or infer any transfer of
ownership.
Interference Issues
This Equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
commercial or industrial installation. This equipment generates, uses, and
can radiate radio frequency energy. It may cause harmful interference to
radio communications if the equipment is not installed and used in
accordance with the instructions.

FCC Warning
This Equipment has been tested and found to comply with the limits for a
Class-A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy. It may cause harmful interference
to radio communications if the equipment is not installed and used in
accordance with the instructions. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

1
Overview
Introduction
The unmanaged industrial switch is a cost-effective solution and meets
the high reliability requirements demanded by industrial applications.
High-Speed Transmissions
The Industrial switch includes a switch controller that can automatically
sense transmission speeds (10/100/1000 Mbps). The RJ-45 interface
can also be auto-detected, so MDI or MDI-X is automatically selected
and a crossover cable is not required. All Ethernet ports have memory
buffers that support the store-and-forward mechanism. This assures
that data is properly transmitted.
Dual Power Inputs
To reduce the risk of power failure, the Industrial switch provides dual
power inputs. When power failure occurs, the device will automatically
switch to the secondary power input.
Flexible Mounting
The industrial switch is extremely compact and can be mounted on a
DIN-rail or a panel, so it is suitable for any space-constrained
environment.
Wide Operating Temperature
The operating temperature of the Industrial switch is in the range
between -20 ~ 60oC or -40 ~ 75oC. With such a wide range, you can use
the Industrial switch in some of the harshest industrial environments
that exist.
Easy Troubleshooting
LED indicators make troubleshooting quick and easy. Each RJ45 port
has 2 LED indicators that display the link status, transmission speed
and collision status. Also other LED indicators help you diagnose the
system immediately.

2
Features / Model List
Store-and-Forward switching architecture
8K MAC address table
Supports full/half duplex flow control
IEEE 802.3at/af PoE+ standard (PoE models)
Supports MDI/MDI-X auto-crossover
Relay contact to connect with alarm system
Provides flexible mounting: DIN-rail, Panel Mounting*
Model Name
10/100TX
10/100/1000T
100/1000M
SFP
Power
Supply
Operating
Temperature
IPES-0104GT-4-48V
4 (PoE)
1
0
45~57VDC
-20 ~ 60℃
IPES-0104GT-4-48V-E
4 (PoE)
1
0
45~57VDC
-40 ~ 75℃
IPES-0104GT-4-12V
4 (PoE)
1
0
9.5~57VDC
-20 ~ 60℃
IPES-0104GT-4-12V-E
4 (PoE)
1
0
9.5~57VDC
-40 ~ 75℃
IPES-0204DFT-4-48V
4 (PoE)
1
1
45~57VDC
-40 ~ 75℃
IPES-0204DFT-4-12V
4 (PoE)
1
1
9.5~57VDC
-40 ~ 75℃
IES-0204DFT
4
1
1
9.5~60VDC
-40 ~ 75℃
*Optional

3
Packing List
1 x Industrial Ethernet Switch (w/ terminal block and DIN-Rail kit)
Caps for RJ45-port and SFP-port
Safety Precaution
Attention
If DC voltage is supplied by an external circuit, please use a
protection device on the power supply input.

4
Hardware Description
In this paragraph, we will introduce the Industrial switch’s dimensions,
port, cabling information, and wiring installation.
Dimensions
IPES-0204DFT-4-48V:
35 x 152 x 105 mm (W x H x D)

5
IPES-0204DFT-4-12V:
43 x 152 x 105 mm (W x H x D)
IPES-0104GT-4-48V / IPES-0104GT-4-48V-E:
35 x 152 x 105 mm (W x H x D)

6
IPES-0104GT-4-12V / IPES-0104GT-4-12V-E:
43 x 152 x 105 mm (W x H x D)
IES-0204DFT:
35 x 152 x 105 mm (W x H x D)

7
Wiring the Power Inputs
Please follow the steps below to insert the power wires.
Note
The wire gauge for the terminal block should be in the range
between 12~ 24 AWG.
V+ V-
V+ V1-
1. Insert the positive and negative wires into the V+ and V-
contacts on the terminal block connector.
2. Tighten the wire-clamp screws to prevent the DC wires
from loosing.

8
Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block connector
as the picture shows below. Inserting the wires, the switch will detect the
fault status of the power failure, or port link failure (available for managed
model) and then forms an open circuit. The following illustration shows an
application example for wiring the fault alarm contacts.
[NOTE]
The wire gauge for the terminal block should be in the range
between 12 ~ 24 AWG.
Insert the wires into the fault alarm contacts

9
LED Indicators
IES-0204DFT
IPES-0104GT-4-48V
IPES-0104GT-4-48V-E
IPES-0104GT-4-12V
IPES-0104GT-4-12V-E
IPES-0204DFT-4-48V
IPES-0204DFT-4-12V

10
The LED indicators located on the front panel display the power status
and network status of the Industrial switch; each has their own specific
meaning as the table shown below.
LED
Color
Description
PWR1
Green
On
Power input 1 is active
Off
Power input 1 is inactive
PWR2
Green
On
Power input 2 is active
Off
Power input 2 is inactive
Fault
Red
On
Power input 1 or 2 is inactive
Off
Power input 1 and 2 are both functional, or no power
inputs
6
Green
On
A network device is detected.
Blinking
The port is transmitting or receiving packets from
the TX device.
LNK/ACT
Green
On
A network device is detected.
Blinking
The port is transmitting or receiving packets from
the TX device.
FDX/COL
Yellow
On
Full-duplex mode
Blinking
Collision occurs
PoE
Yellow
On
The port is operating in PoE mode.
Off
The port is not operating in PoE mode.
Dip Switch (IES-0204DFT / IPES-0204DFT-4)
The SFP speed can be selected by switching the DIP switch.
(The DIP switch will not work when switch is in power on status, please set the DIP then
power on the switch.)

11
RJ-45 Pin Assignments
The UTP/STP ports will automatically sense for Fast Ethernet
(10Base-T/100Base-TX) or Gigabit Ethernet
(10Base-T/100Base-TX/1000Base-T) connection. Auto MDI/MDIX means that
the switch can connect to another switch or workstation without changing
straight through or crossover cabling. See the figures below for straight
through and crossover cable schema.
10/100Base-TX Pinouts
Pin Number
Assignment
1
Tx+
2
Tx-
3
Rx+
6
Rx-
Note
“+” and “-” signs represent the polarity of the wires that make up
each wire pair.
The table below shows the 10Base-T/100Base-TX MDI and MDI-X port
pinouts.
Pin Number
MDI-X Signal Name
MDI Signal Name
1
Receive Data plus (RD+)
Transmit Data plus (TD+)
2
Receive Data minus (RD-)
Transmit Data minus (TD-)
3
Transmit Data plus (TD+)
Receive Data plus (RD+)
6
Transmit Data minus (TD-)
Receive Data minus (RD-)

12
10/100Base-TX Cable Schema
Straight Through Cable Schema
Crossover Cable Schema
10/100/1000Base-T Pinouts
The table below describes the gigabit Ethernet RJ-45 pinouts.
Pin
Signal name
Description
1
BI_DA+
Bi-directional pair A+
2
BI_DA-
Bi-directional pair A-
3
BI_DB+
Bi-directional pair B+
4
BI_DC+
Bi-directional pair C+
5
BI_DC-
Bi-directional pair C-
6
BI_DB-
Bi-directional pair B-
7
BI_DD+
Bi-directional pair D+
8
BI_DD-
Bi-directional pair D-

13
10/100/1000Base-T Cable Schema
The following two figures illustrate the 10/100/1000Base-T cable
schema.
Straight Through Cable Schema
Crossover Cable Schema
Cabling
Use unshielded twisted-pair (UTP) or shielded twisted-pair (STP)
cable for RJ-45 connections: 100Ω Category 3, 4 or 5 cable for
10Mbps connections, 100Ω Category 5 cable for 100Mbps, or 100Ω
Category 5e/above cable for 1000Mbps connections. The cable
between the switch and the link partner (switch, hub, workstation, etc.)
must be less than 100 meters (328 ft.) long.
Fiber segment using single-mode connector type must use9/125 µm
single-mode fiber cable. User can connect two devices in the distance

14
up to 30km.
Fiber segment using multi-mode connector type must use 50 or
62.5/125 µm multi-mode fiber cable. User can connect two devices
up to 2kmdistances.
Gigabit / 100M SFP port:
The small form-factor pluggable (SFP) is a compact optical transceiver
used in optical communications for both telecommunication and data
communications. The SFP slots supporting Gigabit speed up to
1000Mbps. –DSFP/-DFT models support dual speed 100M or 1000Mbps.
They are used for connecting to the network segment with single or
multi-mode fiber. You can choose the appropriate SFP transceiver to plug
into the slots. Then use proper multi-mode or single-mode fiber according
to the transceiver. With fiber optic, it transmits at speed up to 1000 Mbps
or dual speed (-DSFP/-DFT models) and you can prevent noise
interference from the system.
To connect the transceiver and LC cable, please follow the steps shown
below:
First, insert the transceiver into the SFP module. Notice that the triangle
mark is the bottom of the module.
Transceiver to the SFP module