Lantech IPES-3408GSFP User manual

Lantech
IPES-3408GSFP
4 1000 SFP +8 10/100TX L2 + PoE
Industrial Managed Switch
User Manual
Beta.04
July. 2013

Recommendation for Shielded network cables
STP cables have additional shielding material that is used to reduce external interference. The
shield also reduces the emission at any point in the path of the cable. Our recommendation is
to deploy an STP network cable in demanding electrical environments. Examples of
demanding indoor environments are where the network cable is located in parallel with
electrical mains supply cables or where large inductive loads such as motors or contactors are
in close vicinity to the camera or its cable. It is also mandatory to use an STP cable where the
power device (like IP camera) is used outdoors or where the network cable is routed outdoors.

FCC Warning
This Equipment has been tested and found to comply with the limits for a
Class-A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy. It may cause harmful interference to radio
communications if the equipment is not installed and used in accordance
with the instructions. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

1
Chapter 1 Introduction
The IPES-3408 series Managed Industrial Switch is a cost-effective solution and meets
the high reliability requirements demanded by industrial applications. Using fiber port can
extend the connection distance that increases the network elasticity and performance.
1.1 Hardware Features
Standard
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX
IEEE802.3z Gigabit fiber
IEEE802.3x Flow Control and Back Pressure
IEEE802.3ad Port trunk with LACP
IEEE802.1d Spanning Tree
IEEE802.1w Rapid Spanning Tree
IEEE802.1s Multiple Spanning Tree
IEEE 802.3ad Link Aggregation Control Protocol (LACP)
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
IEEE 802.1X User Authentication (Radius)
IEEE802.1p Class of Service
IEEE802.1Q VLAN Tag
IEEE802.3at/af Power over Ethernet
IEEE 802.3az Efficient Energy Ethernet
Switch
Architecture
Back-plane (Switching Fabric): 9.6Gbps
Packet throughput ability (Full-Duplex): 23.8Mpps
@64bytes
Transfer Rate
14,880pps for Ethernet port
148,800pps for Fast Ethernet port
1,488,000pps for Gigabit Fiber Ethernet port
MAC Address
16K MAC address table

2
Connector
10/100TX: 8 x RJ-45 type connector
Mini-GBIC: 4 x 1000 SFP Sockets
Power & P-Fail connector: 1 x 6-pole terminal block
RS-232 connector: 1 x RJ-45 type connector
Network Cable
10Base-T: 2-pair UTP/STP Cat. 3, 4, 5 cable
EIA/TIA-568 100-ohm (100m)
100Base-TX: 2-pair UTP/STP Cat. 5/ 5E cable
EIA/TIA-568 100-ohm (100m)
Optical Fiber
Multi-mode: 50/125um~62.5/125um; Single mode: 9/125um
Wavelength: 850nm (Multi-mode) / 1310nm (Single-mode)
Protocol
CSMA/CD
LED
Per unit: Power 1 (Green), Power 2 (Green), P-Fail (Red)
Ethernet port: Link/Activity (Green), Speed (Green); Mini-
GBIC: Link/Activity (Green)
Power Supply
48~56VDC, Redundant power input with 1500VDC isolation
-48VDC is single power input
Power
Consumption
10Watts (switch)/ 240Watts(with PoE)
Operating
Humidity
5% to 95% (Non-condensing)
Operating
Temperature
-20oC ~ 60oC
Storage
Temperature
-40oC ~ 85oC
Case Dimension
Metal case. IP-30,
65 (W) x 105 (D) x 152 (H) mm
Installation
DIN rail and wall mount ear
EMI
FCC Class A, CE EN61000-4-2, CE EN61000-4-3, CE EN-
61000-4-4, CE EN61000-4-5,
CE EN61000-4-6, CE EN61000-4-8, CE EN61000-4-11, CE
EN61000-4-12, CE EN61000-6-2, CE EN61000-6-4

3
Stability Testing
IEC60068-2-32 (Free fall), IEC60068-2-27 (Shock),
IEC60068-2-6 (Vibration)

4
1.2 Software Features
Management
SNMP v1 v2c, v3/ Web/Telnet/CLI
SNMP MIB
RFC 1215 Traps MIB,
RFC 1213 MIBII,
RFC 1157 SNMP MIB,
RFC 1493 Bridge MIB,
RFC 2674 VLAN MIB,
RFC 1643 EtherLike,
RFC 1757 RMON,
RSTP MIB,
Private MIB,
LLDP MIB
ITU G.8032
Support ITU G.8032 v2 for Ring protection in less than
10ms for self-heal recovery < 256 switches which can be
compatible with other ITU G.8032 metro switches
Support various ring/chain topologies
Ring covers data & multicast* packets
Pro-Ring 2se*
Self-healing recovery in less than 20ms for Single Ring
topology < 50switches
User friendly UI
Auto topology drawing
Topology demo
Auto configuration for G.8032*
Port Trunk with
LACP
LACP Port Trunk: 4 Trunk groups/Maximum 4 trunk
members
Load balancing through LACP to distribute load*
LLDP
Supports LLDP to allow switch to advise its identification
and capability on the LAN

5
CDP
Cisco Discovery Protocol for topology mapping
PoE
Management
PoE Detection to check if PD is hang up then restart
the PD
PoE Scheduling to On/OFF PD upon routine time
table
VLAN
Port Based VLAN
IEEE 802.1Q Tag VLAN (256 entries)/ VLAN ID (Up to 4K,
VLAN ID can be assigned from 1 to 4096.)
GVRP (256 Groups)*,GMRP*, MVRP (Multi VLAN
Registeration)*, QinQ
IPv6
Support dual stack for IPv4 and IPv6
Support Plug and Play function
IPv6 Logo Committee certified
Perform with following RFCs:
1. RFC 2460 –IPv6 Specification
2. RFC 4861 –Neighbor Discovery for IPv6
3. RFC 4862 –IPv6 Stateless Address Auto-configuration
4. RFC 1981 –Path MTU Discovery for IPv6
Network Security
Support 10 IP addresses that have permission to access
the switch management and to prevent unauthorized
intruder.
802.1X access control for port based and MAC based
authentication/MAC-IP-Port binding
Management access control with priority *
256 Policy based Access Control List*
SSL/ SSH for Management

6
TACACS+ for Authentication*
SMTP/Text SMS
Supports SMTP Server and 6 e-mail accounts for
receiving event alert; can send SMS text alert via mobile
Spanning Tree
Supports IEEE802.1d Spanning Tree and IEEE802.1w
Rapid Spanning Tree, IEEE802.1s Multiple Spanning Tree
Quality of Service
The quality of service determined by port, Tag and IPv4
Type of service, IPv4 Different Service
Class of Service
Supports IEEE802.1p class of service, per port provides 4
priority queues
IP Security
Supports 10 IP addresses that have permission to access
the switch management and to prevent unauthorized
intruder.
Login Security
Supports IEEE802.1X Authentication/RADIUS
Port Mirror
Support 3 mirroring types: “RX, TX and Both packet”
IGMP
Support IGMP snooping v1,v2,v3; Supports IGMP static
route
256 multicast groups and IGMP query
Multicast VLAN
Registration*
MVR enables multicast packets go through VLAN for VOD
application
Bandwidth
Control
Support ingress packet filter and egress packet limit.
The egress rate control supports all of packet type.
Ingress filter packet type combination rules are
Broadcast/Multicast/Flooded Unicast packet,
Broadcast/Multicast packet, Broadcast packet only and all
types of packet.
The packet filter rate can be set an accurate value through

7
the pull-down menu for the ingress packet filter and the
egress packet limit.
RTC
Built-in Real Time Clock to keep track of time always
Flow Control
Supports Flow Control for Full-duplex and Back Pressure
for Half-duplex
System Log
Supports System log record and remote system log server
SMTP
Supports SMTP Server and 6 e-mail accounts for receiving
event alert
Relay Alarm
Provides one relay output for port breakdown, power fail
Alarm Relay current carry ability: 1A @ DC24V
SNMP Trap
1. Topology Change
2. Power Trap
3. MAC-Violation
DHCP
Provides DHCP Client/ DHCP Server/ Port and IP Binding
DNS
Provides DNS client feature and supports Primary and
Secondary DNS server
SNTP
Supports SNTP to synchronize system clock in Internet
Firmware Update
Supports TFTP firmware update, TFTP backup and restore.
Configuration
Upload/Download
Supports text configuration file for system quick installation;
Support factory reset button to restore all settings back to
factory default.

8
ifAlias
Each port allows an alphabetic string of 128-byte assigned
as its own unique name via the SNMP or CLI interface

9
Chapter 2 Hardware Description
In this paragraph, it will describe the Industrial switch’s hardware spec, port, cabling
information, and wiring installation.
2.1 Physical Dimension
65 (W) x 105 (D) x 152 (H) mm
2.2 Front Panel
Front Panel of the industrial switch

10
2.3 Top View
The top panel of the Industrial Managed Industrial Switch has one terminal block
connector of two DC power inputs and one fault alarm.
Top Panel of the industrial switch

11
2.4 LED Indicators
The diagnostic LEDs that provide real-time information of system and optional status are
located on the front panel of the industrial switch. The following table provides the
description of the LED status and their meanings for the switch.
LED
Color
Status
Meaning
PWR
Green
On
The switch unit is power on
Off
No power
PWR1
Green
On
Power 1 is active
Off
Power 1 is inactive
PWR2
Green
On
Power 2 is active
Off
Power 2 is inactive
FAULT
Red
On
Power or port failure
Off
No failure
P1 ~ P12
Link/Ack
On
A network device is detected.
Blinking
The port is transmitting or receiving packets
from the TX device.
Off
No device attached
FDX/COL
On
The port is operating in full-duplex mode.
Blinking
Collision of Packets occurs.
Off
The port is in half-duplex mode or no device
is attached.

12
Chapter 3 Hardware Installation
In this paragraph, we will describe how to install the IPES-3408 series Managed
Industrial Switch and the installation points attended to it.
3.1 Installation Steps
1. Unpack the Industrial switch
2. Check if the DIN-Rail is screwed on the Industrial switch or not. If the DIN-Rail is not
screwed on the Industrial switch, please refer to DIN-Rail Mounting section for DIN-
Rail installation. If users want to wall mount the Industrial switch, please refer to Wall
Mount Plate Mounting section for wall mount plate installation.
3. To hang the Industrial switch on the DIN-Rail track or wall.
4. Power on the Industrial switch. Please refer to the Wiring the Power Inputs section
for knowing the information about how to wire the power. The power LED on the
Industrial switch will light up. Please refer to the LED Indicators section for indication
of LED lights.
5. Prepare the twisted-pair, straight through Category 5 cable for Ethernet connection.
6. Insert one side of RJ-45 cable (category 5) into the Industrial switch Ethernet port
(RJ-45 port) and another side of RJ-45 cable (category 5) to the network device’s
Ethernet port (RJ-45 port), ex: Switch PC or Server. The UTP port (RJ-45) LED on
the Industrial switch will light up when the cable is connected with the network device.
Please refer to the LED Indicators section for LED light indication.
[NOTE]
Make sure that the connected network devices support MDI/MDI-X. If it does not
support, use the crossover category-5 cable.
7. When all connections are set and LED lights all show in normal, the installation is
complete.

13
3.2 DIN-Rail Mounting
The DIN-Rail is screwed on the industrial switch when out of factory. If the DIN-Rail is
not screwed on the industrial switch, please see the following pictures to screw the DIN-
Rail on the switch. Follow the steps below to hang the industrial switch.

14
1. First, insert the top of DIN-Rail into the track.
2. Then, lightly push the DIN-Rail into the track.
3. Check if the DIN-Rail is tightened on the track or not.
4. To remove the industrial switch from the track, reverse above steps.

15
3.3 Wall Mount Plate Mounting
Follow the steps below to mount the industrial switch with wall mount plate.
1. Remove the DIN-Rail from the industrial switch; loose the screws to remove the DIN-
Rail.
2. Place the wall mount plate on the rear panel of the industrial switch.
3. Use the screws to screw the wall mount plate on the industrial switch.
4. Use the hook holes at the corners of the wall mount plate to hang the industrial
switch on the wall.
5. To remove the wall mount plate, reverse the above steps.

16
3.4 Wiring the Power Inputs
Please follow the steps below to insert the power wire.
1. Insert AC or DC power wires into the contacts 1 and 2 for power 1, or 5 and 6 for
power.
2. Tighten the wire-clamp screws for preventing the wires from loosing.
[NOTE]
The wire gauge for the terminal block should be in the range between 12 ~ 24
AWG.

17
3.5 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block connector as the picture
shows below. Inserting the wires, the switch will detect the fault status of the power
failure, or port link failure (available for managed model) and then forms an open circuit.
The following illustration shows an application example for wiring the fault alarm contacts.
[NOTE]
The wire gauge for the terminal block should be in the range between 12 ~ 24
AWG.
Insert the wires into the fault alarm contacts