Lantronix xPrintServer User manual

Part Number 900-640-R
Revision A November 2012
xPrintServer
Office Edition
User Guide

xPrintServer User Guide 2
Copyright & Trademark
© 2012 Lantronix, Inc. All rights reserved. No part of the contents of this book may be transmitted
or reproduced in any form or by any means without the written permission of Lantronix.
Lantronix® is a registered trademark and xPrintServer™ is a trademark of Lantronix, Inc.
Windows®, Active Directory® and Internet Explorer® are registered trademarks of Microsoft
Corporation. Mozilla® and Firefox® are registered trademarks of the Mozilla Foundation.
Chrome™ is a trademark of Google. AirPrint™ is a trademark of Apple Inc. and Apple®, OS X®,
Safari®, iTunes®, Bonjour®, iPod®, iPad® and iPhone® are registered trademarks of Apple Inc.
iOS® is a registered trademark of Cisco. Opera™ is a trademark of Opera Software ASA. All
other trademarks and trade names are the property of their respective holders.
Contacts
Lantronix Corporate Headquarters
167 Technology Drive
Irvine, CA 92618, USA
Toll Free: 800-526-8766
Phone: [phone]
Fax: [phone]
Technical Support
Online: www.lantronix.com/support
Sales Offices
For a current list of our domestic and international sales offices, go to the Lantronix web site at
www.lantronix.com/about/contact.
Disclaimer & Revisions
The information in this guide may change without notice. The manufacturer assumes no
responsibility for any errors that may appear in this guide.
Revision History
Date
Rev.
Comments
November 2012
A
Initial document for firmware release 3.0.0-16.

xPrintServer User Guide 3
Table of Contents
Copyright & Trademark ___________________________________________________ 2
Contacts_______________________________________________________________ 2
Disclaimer & Revisions ___________________________________________________ 2
Revision History_________________________________________________________ 2
List of Figures __________________________________________________________ 6
List of Tables ___________________________________________________________ 6
1: Introduction 7
Network, Home and Office Editions__________________________________________ 7
Key Features ___________________________________________________________ 7
Supported iOS Devices ___________________________________________________ 8
Supported Printers and Printer Protocols _____________________________________ 8
Supported DHCP Configuration ____________________________________________ 8
Supported Browsers _____________________________________________________ 9
Product Information______________________________________________________ 9
Serial Number_______________________________________________________ 9
IP Address__________________________________________________________ 9
2: Installation 10
Package Contents ______________________________________________________ 10
User-Supplied Items ____________________________________________________ 10
Hardware Components __________________________________________________ 10
Ethernet LEDs______________________________________________________ 11
Status LEDs _______________________________________________________ 11
Installation Steps _______________________________________________________ 12
Topology Support ______________________________________________________ 13
3: Navigation and Printing 14
Finding the xPrintServer IP Address ________________________________________ 14
System Status on the Home Page _________________________________________ 16
Logging In ____________________________________________________________ 17
Local Authentication Login ____________________________________________ 18
Remote Authentication Login __________________________________________ 18
Logging Off ___________________________________________________________ 18
Navigation ____________________________________________________________ 19
Printing from an iOS Device ______________________________________________ 21
Printing from a Mac OS X Lion Desktop _____________________________________ 22
Setting Up Printing from a Windows 7 Desktop _______________________________ 23

xPrintServer User Guide 4
Performing Add Printer Setup__________________________________________ 23
Configuring a Default Printer___________________________________________ 25
Setting Up Printing from a Windows XP Desktop ______________________________ 25
Performing Add Printer Setup__________________________________________ 25
Configuring a Default Printer___________________________________________ 27
4: Configuration 28
User Administration _____________________________________________________ 28
Changing Passwords ________________________________________________ 28
Adding a New User__________________________________________________ 30
Deleting a User _____________________________________________________ 30
Printer Access Control (Protecting Printer Access)_____________________________ 31
Protecting Printer Access Using MS Active Directory Services ________________ 32
Viewing Configured Printers ______________________________________________ 33
Configuring Printers_____________________________________________________ 34
Enabling or Disabling Discovery________________________________________ 34
Configuring Printers through Auto Discovery ______________________________ 35
Configuring Printers through Discovery __________________________________ 36
Deleting All Configured Printers ___________________________________________ 37
Setting Real Time Clock _________________________________________________ 38
Assigning a Static IP Address to the xPrintServer _____________________________ 39
Admin Printer Configuration Options________________________________________ 39
Printing a Test Page _________________________________________________ 39
Purging Job History__________________________________________________ 40
Deleting a Printer ___________________________________________________ 40
Changing Printer Description __________________________________________ 41
Changing Printer Location ____________________________________________ 41
Showing Shared Printer Information_____________________________________ 42
Sharing a Printer ____________________________________________________ 43
Hiding a Printer _____________________________________________________ 43
Setting Printer Options _______________________________________________ 44
Updating Printer IP Addresses ____________________________________________ 45
Viewing and Exporting Print Jobs __________________________________________ 46
Renaming xPrintServer Device ____________________________________________ 47
Resetting the xPrintServer to Factory Defaults ________________________________ 48
Via the User Interface ________________________________________________ 48
Via the Hardware Reset Button ________________________________________ 48
Restarting the xPrintServer _______________________________________________ 48
Viewing Logs __________________________________________________________ 49
Printer Drivers _________________________________________________________ 50
Downloading Printer Drivers from the Internet _____________________________ 50
Exporting Printer Drivers______________________________________________ 51

xPrintServer User Guide 5
Downloading Printer Drivers from a USB Flash Drive _______________________ 52
Managing Active Directory________________________________________________ 53
Updating Active Directory Configuration__________________________________ 53
Testing Remote User Authentication ____________________________________ 54
Saving Configuration ____________________________________________________ 55
Restoring Configuration__________________________________________________ 56
Proxy Server Configuration _______________________________________________ 57
Testing Proxy Server Connectivity ______________________________________ 58
5: Updating Firmware 59
Updating Firmware via the Lantronix Web Services Website _____________________ 59
Updating Firmware via a Local USB Port ____________________________________ 60
6: Technical Specifications 61
A: Technical Support 62
Diagnostic Support _____________________________________________________ 62
Contact Information_____________________________________________________ 62
B: Troubleshooting 63
Problems and Error Messages ____________________________________________ 63
C: Compliance 64
Declaration of Conformity ________________________________________________ 64
RoHS Notice __________________________________________________________ 65
D: Warranty 66
Index 67

xPrintServer User Guide 6
List of Figures
Figure 1-1 xPrintServer_____________________________________________________________ 7
Figure 1-2 Sample Product Information Label (Type 1) ____________________________________ 9
Figure 1-3 Sample Product Information Label (Type 2) ____________________________________ 9
Figure 1-4 Sample Serial Numbers on Hardware Devices__________________________________ 9
Figure 2-1 xPrintServer LEDs_______________________________________________________ 10
Figure 2-2 Sample xPrintServer Mounting Options ______________________________________ 12
Figure 2-3 Quick Connect Diagram __________________________________________________ 13
Figure 3-1 Serial Number __________________________________________________________ 14
Figure 3-2 Redirected to Login Prompt________________________________________________ 15
Figure 3-3 IP System Status Information on the Home Page_______________________________ 16
Figure 3-4 Login Prompt ___________________________________________________________ 17
Figure 3-5 Navigating the xPrintServer User Interface____________________________________ 19
Figure 3-6 Tabs Available for Users __________________________________________________ 20
Figure 3-7 Sample View of Native Print Menu __________________________________________ 21
Figure 3-8 Sample View of Printer Options_____________________________________________ 21
Figure 4-1 Changing Own Password _________________________________________________ 29
Figure 4-2 Changing Other User Passwords (Admin User Only)____________________________ 29
Figure 4-3 Adding or Deleting a User (Admin User Only)__________________________________ 30
Figure 4-4 Printer Access Control – Local Users ________________________________________ 31
Figure 4-5 Printer Access Control – Remote Users ______________________________________ 32
Figure 4-6 Printer Details and Pop-Up Command Menu __________________________________ 33
Figure 4-7 Printer Discovery Page ___________________________________________________ 34
Figure 4-8 Sample Printer Auto Discovery Report _______________________________________ 35
Figure 4-9 Expanding Detected Printers Information _____________________________________ 36
Figure 4-10 Admin Menu (Defaults to Time-zone Link) ___________________________________ 38
Figure 4-11 New Printer Description__________________________________________________ 41
Figure 4-12 New Printer Location ____________________________________________________ 41
Figure 4-13 Show Share Info Popup__________________________________________________ 42
Figure 4-14 Sample Printer Options __________________________________________________ 44
Figure 4-15 Printer IP Address Page _________________________________________________ 45
Figure 4-16 Print Job Details________________________________________________________ 46
Figure 4-17 Changing the xPrintServer Name __________________________________________ 47
Figure 4-18 Logs_________________________________________________________________ 49
Figure 4-19 Drivers List Tab ________________________________________________________ 50
Figure 4-20 Export Drivers Button ___________________________________________________ 51
Figure 4-21 Loaded Drivers Tab_____________________________________________________ 52
Figure 4-22 Active Directory Configuration_____________________________________________ 53
Figure 4-23 Saving Configuration ____________________________________________________ 55
Figure 4-24 Restoring Configuration__________________________________________________ 56
Figure 4-25 Configuring Proxy Server ________________________________________________ 57
Figure 5-1 Firmware Update Options _________________________________________________ 59
List of Tables
Table 2-1 Status LED, Top of Device _________________________________________________ 11
Table 4-1 Comparing Admin and Non-Admin User Privileges ______________________________ 28
Table 6-1 Technical Specifications ___________________________________________________ 61

xPrintServer User Guide 7
1: Introduction
The xPrintServer is a patent-pending AirPrint print server which provides wireless printing
capabilities for iPad, iPhone and other devices with iOS-enabled AirPrint applications for
unlimited network printers and 8 USB printers (USB hub not included). xPrintServer Office
Edition also enables printing to USB printers from Mac OS X Lion and Windows (XP, 7). Simply
plug the xPrintServer into your network (router or switch with wireless access point), then plug
your USB printer(s) into the xPrintServer. Within seconds the xPrintServer will auto-discover your
printers to enable printing from iPads and iPhones.
Figure 1-1 xPrintServer
Network, Home and Office Editions
The xPrintServer comes in Network, Home and Office editions. This user guide documents the
features and functionality of the xPrintServer Office Edition.
Key Features
No additional software is needed on the iOS device
Simple configuration
Supports up to 8 USB printers via USB hub and an unlimited number of network-attached
printers.
Note: Up to 10 network-attached printers is recommended for optimal performance. Print jobs
process one at a time regardless of the number of configured printers. The xPrintServer includes
one USB port as a part of the unit; an additional USB hub for connecting additional USB printers
is not included.
Automatic printer discovery and configuration (for supported printers)
Security features
External LED status indicator
Configuration via browser (HTTP)

1: Introduction
xPrintServer User Guide 8
Supported iOS Devices
xPrintServer supports all iOS-enabled AirPrint applications. AirPrint is included in all newer
generation Apple® devices with iOS 4.2 and later. These include:
iPad (all versions)
iPhone (3GS or later)
iPod Touch (3rd generation or later)
Supported Printers and Printer Protocols
See http://www.lantronix.com/it-management/mobile-print-servers/supported-printer-list.html for
the latest list of all supported printers. This list is periodically updated with new printers.
Supported DHCP Configuration
xPrintServer supports both DHCP and Static IP Address Assignments. The following items are
configured via Static IP or DHCP.

1: Introduction
xPrintServer User Guide 9
Supported Browsers
Lantronix supports the latest version of Internet Explorer, Mozilla Suite, Mozilla Firefox, Safari,
and Chrome.
Product Information
You will need the serial number of your xPrintServer device when setting up your xPrintServer
user interface. The serial number can be found on the product information label adhered to your
device. One of two types of product information labels will be adhered to your xPrintServer
device (see Figure 1-2 or Figure 1-3 below).
Figure 1-2 Sample Product Information Label (Type 1)
Figure 1-3 Sample Product Information Label (Type 2)
Serial Number
A serial number is a unique, identifying number specific to each hardware device including an
xPrintServer, printer or any Apple iOS device.
Figure 1-4 Sample Serial Numbers on Hardware Devices
IP Address
Every device connected to an IP network must have a unique IP address.The xPrintServer gets
a unique IP address from the DHCP server on your network (default method) or can be manually
configured with a static IP address.
Bar Code
Product Revision
Serial Number
Part Number
Manufacturing
Code Date
Country of Origin
Manufacturing
Code Date
Product Revision
Country
of Origin
Datamatrix
Bar Code
Part Number
Serial
Number
00-80-A3-8E-00-63
or
00:80:A3:8E:00:63
or
0080A38E0063

xPrintServer User Guide 10
2: Installation
This chapter describes how to install your xPrintServer.
Package Contents
Your xPrintServer product package includes the following:
One (1) xPrintServer
One (1) Quick Start Guide
One (1) RJ-45 Ethernet Cable (3 ft)
One (1) Power Supply with Regional Adapters
Mounting Bracket with Two (2) Screws
Four (4) Rubber Feet
User-Supplied Items
You also need the following items to install and operate your xPrintServer:
A working power outlet
WI-FI Access Point
Network-Attached Printer (wired or wireless)
USB Printer (if any)
Your iOS device (e.g., iPad, iPhone) with connection to the network via WI-FI
Hardware Components
There is one USB port, one power input, one Ethernet port, and two types of LED indicators on
the xPrintServer. The LEDs provide information about device activity and status.
Figure 2-1 xPrintServer LEDs
Power Input
USB Port
Status LED
Ethernet Port
Right LED
Left LED

2: Installation
xPrintServer User Guide 11
Ethernet LEDs
There are two LEDs located on the upper left and right corners of the Ethernet socket
(see Figure 2-1). These indicate the status of the connection.
Left LED
Green ON, 100Mbps Ethernet Link
Green Blinking, 100Mbps Activity
Orange ON, 10Mbps Ethernet Link
Orange Blinking, 10Mbps Activity
OFF, No Ethernet Link
Right LED
Always OFF
The Ethernet port can connect to an Ethernet (10Mbps) or Fast Ethernet (100Mbps) network.
Status LEDs
The Status LED on the xPrintServer device is incorporated into the “X” letter of the Lantronix logo
on the top of the device. The behavior of this LED indicates the type of activity occurring in the
xPrintServer device. The Status LED color is orange when lit, and unique display patterns
indicate the specific type of activity. The LED may display a solid light, display no light, slowly
glow on, slowly glow off, or flash on/off.
Table 2-1 Status LED, Top of Device
Orange “X” LED
Description
Solid
A continuous solid light indicates the power is on or the device is booting.
OFF
No light indicates the power is off.
Blinking
Even blinking pattern indicates the device is printing.
Glow/Dim
(Repeating Pattern)
Pulsating pattern of glowing and dimming light cycle occurring once every three
seconds. Indicates the device is booted, idle and waiting for a job.
Code 1
A repeating pattern of a single flash followed by two seconds of
no light indicates the device is obtaining the DHCP address.
Note: Codes 1
through 7
indicate a
grouped number
of flashes in the
Orange “X” LED
separated by a
two second
interval where
the light is off.
The specific
code/number of
flashes
separated by a
two second no-
light interval
indicates a
specific status as
Code 2
A repeating pattern of two flashes followed by two seconds of no
light indicates there are no configured printers.
Code 3
A repeating pattern of three flashes followed by two seconds of no
light indicates a factory default reset.
Code 4
A repeating pattern of four flashes followed by two seconds of no
light indicates a successful firmware update.
Code 5
A repeating pattern of five flashes followed by two seconds of no
light indicates a failed firmware update.
Code 6
A repeating pattern of six flashes followed by two seconds of no
light indicates a printing error.
Code 7
A repeating pattern of seven flashes followed by two seconds of
no light indicates printer discovery is in process.

2: Installation
xPrintServer User Guide 12
Orange “X” LED
Description
Code 8
A repeating pattern of eight flashes followed by two seconds of no
light indicates USB device (printer or flash drive) discovery is in
progress.
described in the
grey cells to the
left.
Installation Steps
With all xPrintServer package contents and the requisite user-supplied items listed above, you
may begin installation.
1. Make sure printing from your Windows or Mac computer (from which the USB printer is
directly attached) is working before proceeding. If you are installing a new USB printer, this
may require downloading and installing printer drivers to your desktop from the printer
manufacturer.
2. Position the xPrintServer device. The xPrintServer can simply be placed as it is on a desk or
other secure flat surface. Here are additional options:
- To install the rubber feet on the xPrintServer (for added grip and stability on a flat
surface), peel to unveil the adhesive strip on each rubber foot and press one foot onto
each of all four bottom corners of the xPrintServer.
- To secure the xPrintServer into a server rack, utilize the included mounting bracket and
screws. There are a variety of ways to mount the bracket and then the xPrintServer unit,
including the two sample methods in Figure 2-2.
Figure 2-2 Sample xPrintServer Mounting Options
or

2: Installation
xPrintServer User Guide 13
3. Connect the USB printer cable to the USB port of the xPrintServer (if any).
4. Connect the network cable from the wireless router/switch to the xPrintServer.
5. Power on the xPrintServer with the supplied power cord. The xPrintServer will automatically
set-up all printers on your network and/or USB-connected printers.The glowing “X” will blink
quickly for about 30 seconds, and then it will pulse slowly to show it’s ready for printing.
6. Monitor the LEDs on the xPrintServer for activity and status information (see Ethernet LEDs
and Status LEDs).
Figure 2-3 Quick Connect Diagram
Topology Support
The xPrintServer is hardwired (via standard CAT-5) cabling to a router, switch or hub. The system
requires an Access Point (A/P) be also hardwired and connected to the network. The iOS devices
associates with the A/Pand communicates to the xPrintServer when a print job is ready to be
processed. The xPrintServer communicates with network attached printer(s); the printers may
either be wired or wirelessly connected to the network.
For the xPrintServer to auto-detect printers on bootup, the xPrintServer and printers must be on
the same subnet. After auto-detection has been completed, the xPrintServer can then be
relocated to a different subnet (WI-FI connected subnet that iOS devices are connected to)
assuming that subnet can route to the previous subnet.
The xPrintServer uses Zeroconf to advertise print services to the iOS device(s) and requires
either one or both of the following:
Both the iOS device and the xPrintServer are on the same subnet.
The iOS device and xPrintServer are on different subnets but multicast traffic is
communicated between the subnets.
Multicast configuration and support can be found in the Lantronix knowledgebase. You may
perform word searches, such as for “multicast”, at http://www.lantronix.com/resources/.

xPrintServer User Guide 14
3: Navigation and Printing
This chapter explains how to navigate and use your xPrintServer user interface including
directions on how to login and log out, how to change your password, and most importantly, how
to print from your iOS device.
Finding the xPrintServer IP Address
Use these directions to find your device IP address through which you may log into your
xPrintServer device. Internet access is required.
Every xPrintServer device has a unique, identifying serial number that can be found on the
product information label (see Figure 1-2). As part of the initialization/boot up process, the
xPrintServer will automatically register its IP address and associated serial number with the
Lantronix Web Services website (http://www.lantronix.com/findmyxprintserver) which in turn
provides the unique IP address of the xPrintServer device. You may then use the xPrintServer IP
address to log into the user interface for printing management.
Use these directions to find the IP address of a new xPrintServer device.
1. Open an internet web browser. See Supported Browsers.
2. Enter http://www.lantronix.com/findmyxprintserver into the web browser address bar.
3. Press Enter on the keyboard. You will be prompted for the xPrintServer serial number.
4. Enter the serial number of your xPrintServer.The serial number can be found on the
product information label attached to your xPrintServer packaging (see Figure 1-2). It is an
alphanumeric set of 12 characters.
Figure 3-1 Serial Number

3: Navigation and Printing
xPrintServer User Guide 15
5. Click the Go! button. You will be redirected to your xPrintServer URL, after which a login
prompt will appear.
Figure 3-2 Redirected to Login Prompt
6. Enter the default Admin user login information.
User Name: admin
Password: PASS
You will be redirected to your xPrintServer device URL where you will see the
System Status on the Home Page.
7. Take note of the IP address of your xPrintServer device for all future logins.
Note: Your xPrintServer IP address is assigned by DHCP by default, however, you can manually
configure a static IP address. See Assigning a Static IP Address to the xPrintServer.
Note: Upon initial login, modify the default “PASS”
password as soon as possible for security reasons.
See Changing Passwords.
Admin User
Default Login
User Name: admin
Password: PASS

3: Navigation and Printing
xPrintServer User Guide 16
System Status on the Home Page
You will see your xPrintServer System Status information on the Home page whenever you
log into your xPrintServer URL.
Figure 3-3 IP System Status Information on the Home Page
The System Status information includes your IP address along with other important system
status information:
Edition
The edition of xPrintServer (Office Edition).
Version
The current version of your firmware.
Name
The configurable name for the xPrintServer device. The default name is xPrintServer.
IP Address
The unique IP address associated with your xPrintServer device. This IP address may
be used to directly pull up the user interface of a connected and live xPrintServer.
Serial Number
The unique serial number associated with the xPrintServer device which should match
what is on the product information label.
Up time
The amount of time the xPrintServer has been operational since powered on or last
restarted.
Configured Printers
The number of total discovered printers available for use on iOS devices.
Current Status
The current status of the xPrintServer.

3: Navigation and Printing
xPrintServer User Guide 17
Time-zone
The configured time zone (can be changed through the Admin page).
Status Time
The time at which the system status information you see on the screen was captured.
Locator LED
Clicking the light bulb will cause the “X” LED on top of the xPrintServer unit to blink
rapidly. Clicking the light bulb again turns off this feature. This feature is useful in
situations where you wish to identify a specific xPrintServer amongst multiple units.
Logging In
Once the xPrintServer is installed (see Installation Steps) and the IP address discovered (see
Finding the xPrintServer IP Address and Initial Login), you may follow these directions to login to
xPrintServer via Local or Remote Authentication at any time.
Note: The xPrintServer does not use the MS Active Directory services for xPrintServer GUI
authentication. It will only use the locally configured user database for the xPrintServer GUI
authentication.
Figure 3-4 Login Prompt
To Login:
1. Open an internet web browser.
2. Enter the IP address of your xPrintServer device.
Note: If Bonjour is installed on your computer or Mac, you may also access the user interface by
entering:
xPrintServer.local
3. Enter your login information when prompted.
User Name
Password
You are logged into the xPrintServer user interface when you see System Status on the Home
Page.

3: Navigation and Printing
xPrintServer User Guide 18
Local Authentication Login
Logging in through local authentication logs you directly into the xPrintServer unit through the
local database.
Remote Authentication Login
Remote authentication allows authentication of users through Microsoft Active Directory. This is
a feature that can be enabled by the Admin user. If Active Directory is enabled, the xPrintServer
communicates with a remote server to authenticate user passwords (see Managing Active
Directory). The Admin user must first establish a remote authentication user name and password
in Microsoft Active Directory. Once established, users using remote authentication can follow the
same steps under Local Authentication Login to login. Remote authentication is disabled by
default.
Note: Though the xPrintServer supports remote authentication using MS Active Directory, it is
only used for authenticating print jobs sent to xPrintServer-protected printers. The xPrintServer
GUI access will only authenticate against the xPrintServer-configured local user database.
Logging Off
1. Click the Log-Off tab located at the top far right of any xPrintServer user interface page. You
will be prompted to close out of your browser window.
2. Close out of your browser to completely log off.

3: Navigation and Printing
xPrintServer User Guide 19
Navigation
Basic navigation features for the xPrintServer user interface are outlined in this section.
Figure 3-5 Navigating the xPrintServer User Interface
Sometimes multiple pages are
necessary to list all the items in
the Printers, Jobs and Logs
pages. In these circumstances,
page navigation features will
become available at the bottom of
the screen.
Double-click to sort
table information by
column heading
Links
available for each
page are listed here
When a specific printer
on the Printers
page is clicked, details
about this printer will
appear in grey fields
beneath the printer list.
See Figure 4-6.
Search
Clicking the
button beside a
particular table list
item will pull up the
popup command
menu associated
with that item.
Tabs allow you to move between
xPrintServer pages and to Log-Off
Go to the first page Go to the last page
Go backward one page… Go to the next page

3: Navigation and Printing
xPrintServer User Guide 20
As illustrated above, basic navigation features for the xPrintServer user interface include the
following:
Tabs
All the functionality of your xPrintServer user interface is divided between the Home, Admin,
Jobs, Printers, Logs and Log-Off tabs located across the top of the user interface.Only the
Admin user has full access to the functionality of all tabs within the xPrintServer user
interface. Non-Admin users only have access to the Home, Jobs and Log-Off tabs. See
Figure 3-6 to compare Admin user and Non-Admin user access. Access these pages by
clicking the same-named tab along the top of the screen. For instance, click the Jobs tab to
get to the Jobs page or click Home to get to the Home page.
Links
Click to select from the links/commands available for each page. All links available for a
particular web page are displayed along the left side. For instance, links to Active,
Completed and All jobs are available on the left side of the Jobs page.
Search
A Search field is available for the Jobs, Printers and Users tabs. The search field features
dynamic filtering that provides results based on the search string entered into the search
field. The results dynamically update according to the search parameters entered in the
search field. Deleting all contents of the Search field removes the filter and will show all
results.
Button
This button may be found beside all items listed on the Jobs and Printers pages. Click the
button beside a particular print job or printer on these pages to pull up a popup command
menu with commands that are available for that item.
Log-Off Tab
A Log-Off tab located at the far upper right of every xPrintServer user interface page allows
you to logout easily.
Figure 3-6 Tabs Available for Users
Non-Admin users
have access to only
the Home, Jobs
and Log-Off tabs.
The Admin User has access
to all seven tabs of the
xPrintServer user interface
(Home, Admin, Jobs,
Printers, Users, Logs and
Log-Off).