Lapcon LAMP LDD-S User manual

1-2mm
2-3mm
26 (Screw hole forstri ke)
D
Unit:mm
markthescrewholeshownonthetemplate.
③
・Closingpoweradjustment
Loosenadjustmentscrew,adjuststrikeplatepositionandre-tighten
・Thisdampermaynotbeabletoslowdownthedoorifitisclosedwithexcessiveforce.
・ThisproductisaSURFACEMOUNTTYPEdoorcloserdamperintendedtobeappliedontheheadframe.
・Thedamperfunctionreducesdoorslammingsoundsandthedoorbeginstocloseslowly
Installation
theClosingpoweradjustmentscrew.
・Attachthecoversforthemainunitandthe
●
Indicator
High
justbeforethecompleteclosingandclosescompletely.
Closingpoweradjustmentscrew
(Surfacemounted)
Installationandusagenotices
・TheLDDmaynotpullthedoorcompletelyclosedwhenusingandoverlyhardlatch.
Installationinstructions
LapconDoorDamper
・Sugatsune'swarantyisfortheproductitselfanddoesnotextendtotheinstallationasawhole.
・Thestrikeplateisfeaturedwithvertical/horizontaladjustmentfunctions.
Partslist
・Despiteextensivein-housetesting,werecommendthatyoutestyourinstallationforproper
interactionbetweenthehingeandtheLDDdamper.
LDD-S
・Featuredwiththefunctionofdoor-closingpoweradjustment.
*LDD-Sbody:1pcs *Bodycover:1pcs
Readthismanualthoroughlyforproperandsafeinstallation.Pleaseretainthismanualforfuture
reference.
*Strikeplateunit:1pcs *Strikeplatecover:1pcs
Bodyinstallationscrew:2pcs
(nominal4×16)
InstructionManual(thismanual):1
Strikeplateinstallationscrew:2pcs
・Quickandeasytoinstall.Justmountitclosetotheverticalframeanddoorstop.(*Dependsontheframewidth.)
Body
Left-handopeningtype(LDD-S-L)issymmetricallyopposed.
4.Attachingthecovers
Verticaladjustmentscrew
Verticaladjustmentrange:+3,-2mm
Suggestedhinge
strikeplatewhilekeepingthedooropen.
Thisonlychangesthefinalclosingpower,notthe
Low
HigheLower
dampingforceoftheLDD-S.
screw.
Checkrollerpositionandadjustfurtherifnecessary.
Whenadjustmentiscompleted,openandclosethedoorseveraltimes
inordertocheckproperfunctionoftheLDD-S.
Checkingbeforetheinstallation
*RIGHTHANDTYPE(LDD-S-R)SHOWN.LEFTHANDTYPE(LDD-S-L)SYMETRICALLYOPPOSITE.
・Concealedhinge
Installation
・
IfCisbetween20mmand25mm:
Templateforstrikeplate:1pc
(nominal3.5×30)
Strike
Thisdrawingshowsaright-handopeningtype(LDD-S-R).
Productfunctionsandfeatures
Incaseoffailure,Sugatsune'sliabilityislimitedtothereplacementoftheproductsbyasimilarone.
・Thecompanyisconductingstrictcheckontheproducts,however,ifanydefectsarefoundonthe
product,contactretailer.
・Thewarrantyperiodisoneyearafterthedayofshipment.Thecompanysresponsibilityshallbe
limitedtoreplacementoftheproduct.
Installandfullyadjustthedoor,hingesandframebeforeinstallingtheLDD-S
2.Strikeplateinstallationprocedure
・Thisproductisforindooruseonly.Donotuseinlocationswhereitisindirectcontactwithwater.
Applicabledoorspecifications
・Doorweightrange:15-40kg(33.6-88lbs.)
・Thisdampereffectivenessmaybelessenedwhenuseinanenvironmentsubjecttostrongdrafts.
・Maximumdoorwidth:900mm(36")

3.Adjustments
Ｒ
・Butthinge (DimensionDmustbe60mmorless)
・Standardtemperatureofuseis0to40℃.
 MountingpositionandinstallationscrewholesdependonthetopframemountingwidthC
FIG1-A
・
IfCis25mmormore:
FIG1-B
OR
FIG2
Squarehole
Left-handopening Right-handopening

1.Mainunitinstallationprocedure
FIG3
Adjustthetemplatesothatitisparallelewiththetopofthedoorand
inthesquareholeshownonthetemplate.
Screwholes
FIG4
screwsprovided.
:Fixthestrikeplatewiththeinstallation
thestrikeplate.(Seebelow.)
beforeopeningandclosingthedoor.
Proceedwiththefinaladjustment
FIG4
FIG5
Ifnecessary,carryoutverticaland/orhorizontaladjustmentsto
theguidegrooveon thestrikeplateasshown.
:ClosethedoorcarefullyandmakesurethattherollerentersintoFIG5
Checkyoudooropeningside
・Ifthehingesareonyourrightwhenpullingthedooropen,choosethe"Right-hand"openingtype.
・Ifthehingesareonyourleftwhenpullingthedooropen,choosethe"Left-hand"openingtype.
Sizeofdoorstopperandtopframe(applicablesizerange)
A-Maximumheightofdoorstopper:15mm
B-Distancefromdoortothebackofthedoorstopper
(=doorstopper+packingthickness):23-33mm
C-Minimumtopframemountingwidth:20mm
FIG2-3 :①Deploythearmandclosethedoorslowlyuntilthearmtouchesthedoor.

②Insertthetemplatebetweenthearmandthedoorsothatthearmrollerfits
Horizontaladjustmentscrew
Horizontaladjustmentrange:±3mm
Closingpowerofthedoorcanbeadjustedbyturning
Topframe
Doorstop
Door
B
A
C
132
32.５
50
152
(Thisdrawingshowsaright-handopeningtype(LDD-S-R).Left-handopeningtype(LDD-S-L)issymmetricallyopposed.)
Centerofbutthinge
Installationdrawing
Door
Hingesidemountingframe
Body
Strike
17.5
60
9
198
35
212
Doorstop
:LineuptheLDD-Sbodywiththetopdoorstopandhinge
sidemountingframe.Fixthebodywiththeprovidedbody
installationscrews.
Doorstop
FIG1-A
Hingesidemountingframe
Screwholes
FIG1-B :LineuptheLDD-Sbodywiththetopdoorstopand25mm
awayfromthehingesidemountingframe.Fixthebodywith
theprovidedbodyinstallationscrews.
C
Screwholes
Hingesidemountingframe
mm25
C
Arm
R
+
−