Lark-Wi Smart Keypad Deadbolt Installation instructions
1
1
www.lark-wi.com/support
Let’s get started!
Need help? We’re here for you.
Visit us online at www.lark-wi.com/support
Smart Keypad Deadbolt
2
2
What’s in the box
3
3
What you’ll need...
Lark-Wi is designed to use wireless to communicate with your phone. Your phone will
then communicate with the server using the cellular or data connection on the device.
Your authorized smart phone will need to have internet connection - either wireless or
cellular data - to operate the lock.
Lark-Wi does require an internet connection for initial Lark-Wi setup (with the mobile
app), Create an account or account login, add smart lock and firmware update.
Mobile Device
iOS 9 (or greater) Apple iPhone®: iPhone 4s, 5, 5s, 6, 6 Plus, 6s, 6s Plus, 7,8,x.
Android:
Compatible with many Android phones running Android 5.0 or greater.
Four AA 1.5v alkaline batteries, we recommend the 4 x lithium 1.5 V battery.
4
4
Easy Install
Mark The Door With Template
Select the height and backset as desired on the door face ; use the TEMPLATE as an indi-
caon to mark the center of the circle on the door face and the center of the door edge.
Drill Holes
Using the marks as a guide to drill a hole Ø2-1/8” (54mm) through the door face for the
lockset, then a hole of Ø1”(25.4mm) for latch .
5
5
Easy Install
Install Latch
a) Insert the latch and ensure it is paralleled to the door face.
Mark the outline of the faceplate, then take out the latch.
b) Chisel 1/8” (3mm) deep along the outline to allow the faceplate to be aligned with the door edge.
c) Insert the latch and ghten it with screws.
Note : please use tapping screws for metal door.
Install Strike
a) To idenfy the center of strike :
close the door, on the basis of the faceplate mark horizontal center line of strike.
Ensure the center of faceplate and the center of strike are aligned.
b) Use the mark as a guide outlines the strike.
Chisel 5/64” (2mm) deep along the strike outline to allow the strike to be aligned with the doorframe.
c) Insert the strike and ghten it with screws.
Note : please use ”tapping screws” for metal door.
6
6
Easy Install
Install Keypad Assembly
a) Ensure the latch bolt must be retracted.
b) Please refer to the diagram below for Cylinder Installaon. Place deadbolt against keypad with tailpiece in horizontal posion inserted through hub of the latch.
c) Pass the IC wire under the latch to the interior side of the door.
7
7
Easy Install
Install Inside Mounng Plate
Pass the IC wire through the wire hole of the mounng plate.
Fix the mounng plate with screws.
If outside lock assembly is lopsided, please loosen the screws to adjust it's posion
and ghten the screws again.
Install receiver module
Connect the IC wire and ensure the tailpiece is engaged with turn piece, then aach
receiver module to the door with screws.
It's oponal to use wood screws. (Wood screws only for wood door)
8
8
Prepare
Adjusng Turn Piece
Turn the turn piece to le for 45 degrees when it's right-handed door.
Turn the turn piece to right for 45 degrees when it's le handed door.
Baeries Installaon
Remove the baery cover (push it up and pull it out).
Insert 4 (AA) 1.5V alkaline baeries and put the baery cover back to the receiver
module.
9
9
Prepare
Download the Lark-Wi app.
Download the lark-wi app from apple store :
Search Apple Store, used Keywords: Lark-Wi , Then select: Lark-Wi
When using your smartphone to lock and unlock the door, make sure the
smartphone is on, Bluetooth is enabled, and the Lark-Wi app is running.
Your authorized smart phone will need to have internet connection - either
wireless or cellular data - to operate the lock.
10
10
Create an Account
Follow the instructions inside the app to create an account, enroll register with your smartphone first .
○
1
1、Open the Lark-Wi app, Select GET STARTING .
2、You can read the Lark-Wi Privacy Policy, Terms of Service and End User License Agreement by tapping the link at the bottom
of the screen. When you are ready to continue, tap I Agree.
3、Enter Your First Name, Last Name.
4、Lark-Wi requires your password to be at least 8 characters long .
○
2○
3○
4
11
11
Create an Account use e-mail (Step 5-8)
Follow the instructions inside the app to create an account, enroll register with your smartphone first .
○
5
5、Take a profile photo or upload one from your phone. Profile photos help Lark-Wi users verify each others’ identities when inviting
and managing access.
6、Select the phone number for your country.
7、For example, you can search for a US mobile phone code of 1
8、If you see a prompt that your region does not support SMS authentication, you only need to use e-mail to register your account,
then you can choose skip
○
6○
7○
8
12
12
Create an Account use e-mail (Step 9-12)
Follow the instructions inside the app to create an account, enroll register with your smartphone first .
9
9、Enter the email address you'd like to use for your account. Again, it’s important to use your real email address.
10、Enter the e-mail, click Next, we will send a verification code to the input of your mailbox, you may need to wait a few minutes,
your mailbox will receive the 6-bit verification code;
11、Please enter your verification code and you get it from your mailbox
12、Click Next, you complete your account registration
10 11 12
13
13
Set up a lock Step 1
○
1
1、Make sure your smart lock is in the reset state, or you just reset your smart lock , than Tap Set Up a Lock.
2、Read the Instructions and Tap Start Setup. The Lark-Wi App Will Begin Scanning For Your Lock.
If no locks found:
- Confirm that the battery has been installed.
- Make sure you're standing in front of the lock.
- Confirm that Bluetooth is enabled on your phone.
3、Choose a lock.
Note: If your Smart Lock uses less than the 2.8 version of APP, you will need to follow the instructions to update the firmware
○
2○
3
Reset - Press for more than 15 seconds and hear the music.
14
14
Set up a lock Step 2
○
4
4、Choose a Name for Your Lock.
5、You Can Add the Lock to an Existing House, or Add a
New House.
6、The App is Scanning For Your Lock, tap continue.
○
5○
6
15
15
Set up a lock Step 3
○
7
7、Beginning the Calibration Process. Follow the Onscreen Instructions
Rotate Your Lock to Unlock .
8、tap continue.
9、Tap the Green Circle to Test Your Lock, Your Lock is Ready to Use.
○
8○
9
16
16
Control My Lock With Lark-Wi App
The Lark-Wi Smart Lock is simple to use. Approach your door and open the Lark-Wi app in your
smartphone.
The red circle indicates that your door is locked. Tap the red circle to unlock your door.
The green circle indicates that your door is unlocked. Tap the green circle to lock your door.
To activate this fea-
ture you must be in
range of your lock.
17
17
Activity Feed
If you are an owner of an Lark-Wi Smart Lock,
you’ll notice an “history” tab in the Home area of the
Lark-Wi app. This opens the Lark-Wi Activity Feed
screen. The Activity Feed shows all of the Lark-Wi Ac-
tivity events in your house, with the most recent event
showing at the top.
All events in your feed are connected with a continu-
ous light gray line. Sometimes events at your door are
related to each other. When these collections of events
occur at the same door with the same user in the same
time span, we call them “stories” and connect them
with a thicker, darker gray line.
18
18
Lock Settings
Tap the Setting Gear Icon Above the Lock Circle.
In the Lock Settings:
Change My Lock Name.
Enable/Disable Lock Sounds.
Enable Auto-Lock .
Find My Lock's Serial Number.
Delete My Lock.
Calibration.
Updating Lock Firmware.
19
19
Send an invite
With Lark-Wi Smart Lock you can choose family, friends, or services from your contacts and issue
them keys in seconds. Simply send each guest an invitation to download the app. After doing so, they
will have instant access to your home based on the access levels you set.
To add a guest you will first need to send them an invite. Please note that invitations to guests will
only work if the guest has a compatible smart phone.
1)Tap Home.
2)Select a house.
3)Select a lock.
○
1○
2○
3
20
20
Send an invite 2
4、Select the sharing Icon on the lower right. Select Invite to add a guest.
5、Invite Your Guest By Entering Their Phone Number, or Their Email, or Selecting Them From Your Contact List.
6、Press Send Invite after selecting your invite option.
7、Your guest will now be listed in your Guest List. They will see your lock in their home.
○
4○
5○
6○
7
Table of contents
