Larson Electronics EPLC2-LB-45LED-RT-WLM User manual

EPLC2-LB-45LED-RT-WLM
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 2
45W Hazardous Location Low Bay LED Fixture
Paint Spray Booth Approved - 6,300 lms - Wall Mount - T5
Instruction Manual
The Larson Electronics EPLC2-LB-45LED-RT-WLM Hazardous Location Low Bay LED Light Fixture provides operators
with a powerful alternative to traditional hazardous location luminaries. Capable of replacing 250-watt metal halide lamps,
this 45-watt low bay LED unit emits 6,300 lumens, carries an IP67 waterproof rating and features an extended lifespan of
60,000+ hours. The factory sealed, hazardous location fixture is protected by a copper-free aluminum housing with an
epoxy powder coated finish.
WARNING
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE
REFERENCE. CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BE CONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OF FIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF LUMINAIRES ELECTRICAL
SYSTEMS. IF NOT QUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE RATED LUMINAIRE FIXTURES VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE EPLC2-LB-45LED-RT-WLM MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL
CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY ALICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
WIRING
Standard pigtail(flying leads) wiring
We strongly encourage a licensed electrician install this product,in all locations especially in outdoor areas
where weatherproofing may be required. Universal voltage driver permits operation at 100V -277V AC, 50 or 60Hz
except those factory ordered with low voltage 11V to 25V AC/DC.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light fixture wires as shown
in thediagram 
Secure each pair of wires according to the diagram. Utilize a junction box or
similar device and take precautionary steps for weatherproofing all
connections if installed in a location where water may come in contact with the
unit. Ensure the unit is properly grounded and that wiring is done according to
all local and national electrical/building codes.

EPLC2-LB-45LED-RT-WLM
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2 of 2
VOLTAGE
This light is universal voltage capable and can be operated with 100-277V AC, 50/60Hz. We also offer a low voltage version
of this LED fixture that operates on AC/DC voltages from 11-25 Volts.
MOUNTING
This hazardous location low bay LED light fixture comes standard with a wall-mount configuration. The mounting component
extends the fixture up to 6" from a flat, vertical mounting surface. Spacing between the mounting component and LED
fixture's fins, which are located at the back of the unit, streamline cool operation. This wall-mounting solution is ideal for
illumination directly above busy sections of facilities, work areas, doorways and more. Additionally, the mounting
configuration can facilitate accurate light placement over control stations, switchboards, panels and segregated sections of
work sites.
Several mounting options including pendant mounting, ceiling mounting and cable mounting can be ordered separately.
Compared to high bay lights, low bay fixtures are recommended for lower mounting heights ranging between 15' to 40'.
WIRING
The hazardous location low bay LED light fixture is equipped with an internal wiring junction box built into the mount of the
fixture. A total of four, 3/4" NPT threaded ports are available for running conduit (located at every corner of the unit).
Additionally, wiring can be passed through the junction box, reducing the need for additional junction boxes. Operators run
wiring directly to the fixture and terminate in the junction box mount. This fixture is factory sealed and does not require a seal
off.
WARNING: CHECK NAMEPLATE
FOR PROPER VOLTAGE. DAMAGE
FROM IMPROPER VOLTAGE WILL
VOID WARRANTY.
MAINTENANCE
Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool down before
performing maintenance.
Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will void
the warranty.
1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend routine
checks to be made on a yearly basis. Frequency of use and environment should determine this. It is
recommended to follow an Electrical Preventive Maintenance Program as described in NFPA 70B:
Recommended practice for Electrical Equipment.
2. The lens should be cleaned periodically as needed to ensure continued photometric performance.
Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use mild soap or a liquid
cleaner.
3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or
contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.
4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

EPLC2-LB-45LED-RT-WLM
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
3 of 3
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The EPLC2-LB-45LED-RT-WLM is designed to provide years of reliable performance. Should the need for replacement
parts arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
[e-mail] OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.